ECU KIA CARNIVAL 2007 Manual PDF

3.Remove the hood latch (A) mounting bolts.
4. Remove the latch (A).
5.Disconnect the hood latch cable (A) and Remove the latch (B).
6.Installation is the reverse of removal.
a.Make sure the hood latch cable is connected properly.
b. Make sure the hood locks securely.
COWL TOP COVER REPLACEMENT

2.Installation is the reverse of removal.
LATCH ASSEMBLY REPLACEMENT
1.Remove the tailgate trim.
2. Disconnect the outside handle rod (A), connector (B).
3.After loosening the mounting screws, then remove the latch assembly (A).
4.Installation is the reverse of removal.
a. Make sure the connector is connected properly and the connecting rod is connected properly.
b. Make sure the tailgate opens properly and locks securely.
ACTUATOR ASSEMBLY REPLACEMENT
1.Remove the tailgate trim.
2. Disconnect the outside handle rod (A), actuator rod (B), key cylinder rod (C) and connector.
3. After loosening the mounting bolt and nuts, then remove the actuator assembly (D).

4.Installation is the reverse of removal.
a.Make sure the connector is connected properly and the connecting rod is connected properly.
b. Make sure the tailgate opens properly and locks securely.
OUTSIDE HANDLE REPLACEMENT
1.Remove the tailgate trim.
2. After loosening the mounting bolt and nuts, then remove the tailgate garnish (A).
3.Disconnect the outside handle rod (A).
4. Loosen the outside handle (B) mounting bolts.

5.Installation is the reverse of removal.
a.Make sure the tailgate opens properly and locks securely.
LIFTER REPLACEMENT
1.Using a screwdriver (A), lift up slightly the socket clips (B) of both ends on the lifter (D), and then remove the lifter
from the bracket (C).

5.Installation is the reverse of removal.
a.Make sure the tailgate opens properly and locks securely.
POWER TAILGATE MOTER ASSEMBLY REPLACEMENT
1.Remove the rear seat assembly.
2. Remove the luggage trim.
3. Disconnect the clip (A), remove the tailgate lifter (B).
4.Disconnect the connector.
5. After loosening the mounting bolts, then remove the tailgate motor assembly (A).
6.Installation is the reverse of removal.

a.Make sure the connector is plugged in properly.
b. Make sure the tailgate opens properly and locks securely.
REAR WIPER REPLACEMENT
1.Using a screwdriver, detach cover (A).
2.Remover the rear wiper (A).
3.Installation is the reverse of removal.
REAR WIPER MOTER ASSEMBLY REPLACEMENT
1.Remove the tailgate trim.
2. Remove the rear wiper.

2.Loosen the bolts, then remove the fuel fill door (A).
3.Remove the fuel fill door (B).
4.Installation is the reverse of removal.
a.Make sure the fuel fill door opens properly and locks securely.
5. Check that the fuel fill door (A) fits flush against the body. If necessary, adjust it.

[RHD]
4.Installation is the reverse of removal.
a.Make sure of connectors is plugged in properly and each rod is connected securely.
b. Make sure the door locks and opens properly.
GLASS REPLACEMENT
1.Remove the front door trim.
2. Remove the door trim seal (A).
3.Carefully move the glass (A) until you can see the bolts, then loosen them. Carefully pull the glass out through the
window slot (B).
4.Installation is the reverse of removal.

5.Installation is the reverse of removal.
a.Make sure the connector is plugged in properly and each rod is connected securely.
b. Make sure the door locks and opens properly.
OUTSIDE HANDLE REPLACEMENT
1.Remove the door trim.
2. Remove the door trim seal.
3. Disconnect the connector (A).
4.Disconnect the lock rod (A) and outside handle rod (B).
5.Loosen the outside handle mounting bolts, remove the outside handle bracket (A).

b.Loosen the hinge mounting bolts (C) slightly, and move the door BACKWARD or FORWARD, UP or DOWN as
necessary to equalize the gaps.
c. Place a shop towel (D) on the jack (E) to prevent damage to the door when adjusting the door.
3.Check that the door and body edges are parallel.
4.Grease the pivot portions of the hinges indicated by the arrows.
5.Check for water leaks.
DOOR STRIKER ADJUSTMENT
Make sure the door latches securely without slamming It.
If necessary, adjust the striker (A): The striker nuts Are fixed. The strike can be fine adjusted up or down, and in or
out. striker ceater to be adjusted max ± 1.5mm
1. Loosen the screws (B), then insert a shop towel between the body and striker(A).