service KIA Magnetis 2006 2.G User Guide
[x] Cancel search | Manufacturer: KIA, Model Year: 2006, Model line: Magnetis, Model: KIA Magnetis 2006 2.GPages: 225, PDF Size: 3.77 MB
Page 95 of 225

REAR DRUM BRAKES
(IF EQUIPPED)Your rear drum brakes don’t have wear
indicators. Have the rear brake linings
inspected if you hear a rear brake
rubbing noise. Also, have your rear
brakes inspected each time you change
or rotate your tires and when you have
the front brakes replaced.
PARKING BRAKE• To set the parking brake, pull the
parking brake handle fully and firmly
upward while applying the service
brake.DRIVING YOUR VEHICLE
4-16
MMSA4012
MMSA4011
CAUTION
Always replace brake linings or
front pads as complete front or
rear axle sets.
CAUTION
Driving with the parking brake on
will cause excessive wear of the
brake linings and pads.
MS-CNA-Eng 4(~39).QXD 7/25/2005 5:16 PM Page 16
Page 154 of 225

assistance. If coolant is not boiling
out, allow the engine to idle and open
the hood to permit the engine to cool
gradually. If the temperature does not
go down with the engine idling, stop
the engine and allow sufficient time
for it to cool.
4. The coolant level should then be
checked. If the level in the reservoir
is low, look for leaks at the radiator
hoses and connections, heater hoses
and connections, radiator, and water
pump. If you find a major leak or
another problem that may have
caused the engine to overheat, do not
operate the engine until the problem
has been corrected. Call an
Authorized Kia Dealer for assistance.
If you do not find a leak or other
problem, carefully add coolant to the
reservoir.If the engine frequently overheats, have
the cooling system checked and repaired.
EMERGENCY STARTINGJUMP STARTINGJump starting can be dangerous if done
incorrectly. Therefore, to avoid harm to
yourself or damage to your vehicle or
battery, follow the jump starting
procedures on the next page. If in doubt,
we strongly recommend that you have a
competent technician or towing service
jump start your vehicle.
6-3
WARNING - Removing
Radiator Cap
Do not remove the radiator cap
when the engine and radiator
are hot. Scalding hot coolant
and steam may blow out under
pressure. This could cause
serious injury.
✻
NOTICE
Use only a 12volt jumper system.
You can damage a 12volt starting
motor, ignition system, and other
electrical parts by using a 24-volt
power supply (two 12-volt batteries
in series or a 24-volt motor
generator set).
MS-CNA-Eng 6.QXD 7/25/2005 5:13 PM Page 3
Page 165 of 225

TOWINGIf emergency towing is necessary, we
recommend having it done by an
Authorized Kia Dealer or a competent
tow-truck service. Proper lifting and
towing procedures are necessary to
prevent damage to the vehicle. State and
local laws applicable to towing vehicles
must be followed.
IN CASE OF EMERGENCY
6-14
MMSA6007A
Wheel dolly
HORN10A Horn
HEAD LP HI15A Headlights (HI)
HEAD LP WASH20A -
DRL15A DRL
FR FOG15A Front fog lights
DIODE-1- Diode 1
SPARE30A Spare fuse
SPARE20A Spare fuse
SPARE15A Spare fuse
SPARE10A Spare fuse
DIODE-2- Diode 2
BLOWER30A Blower
PWR FUSE-230A Power fuse 2
PWR AMP20A Power amp
SUNROOF15A Sunroof
TAIL LP20A Tail lights
PWR FUSE-130A Power fuse 1
ECU10A ECU
RR HTD30A Rear window defroster
MS-CNA-Eng 6.QXD 7/25/2005 5:13 PM Page 14
Page 167 of 225

TOWING WITH A VEHICLE
OTHER THAN A TOW TRUCK
If towing is necessary, we recommend
you to have it done by an Authorized Kia
dealer or a commercial tow truck service.
If towing service is not available in an
emergency, your vehicle may be
temporarily towed using a cable or chain
secured to the emergency towing hook.
Use extreme caution when towing the
vehicle.
A driver must be in the vehicle to steer it
and operate the brakes.
Towing in this manner may be done only
on hard-surfaced roads for a short
distance and at low speeds. Also, the
wheels, axles, power train, steering and
brakes must all be in good condition. Do not try to tow your vehicle when
the wheels are stuck in mud, sand or
similar substances that prevent the
vehicle from being driven out under
its own power.
Avoid towing a vehicle heavier than
the vehicle doing the towing.
The drivers of both vehicles should
communicate with each other
frequently.
IN CASE OF EMERGENCY
6-16Front
MMSA6009A/MMSA6010
Rear
MS-CNA-Eng 6.QXD 7/25/2005 5:13 PM Page 16
Page 168 of 225

Before emergency towing, check that
the hook is not broken or damaged.
Fasten the towing cable or chain
securely to the hook.
Do not jerk the hook. Apply steady
and even force.
To avoid damaging the hook, do not
pull from the side or at a vertical
angle. Always pull straight ahead. Use a towing strap less than 5 m (16
feet) long. Attach a white or red cloth
(about 30 cm (12 inches) wide) in the
middle of the strap for easy visibility.
Drive carefully so that the towing
strap is not loosened during towing.
6-17
✻
NOTICE
• Attach a towing strap to the tow
hook.
Using a portion of the vehicle
other than the tow hooks for
towing may damage the body of
your vehicle.
Use only a cable or chain
specifically intended for use in
towing vehicles. Securely fasten
the cable or chain to the towing
hook provided.
CAUTION
Use extreme caution when towing
the vehicle.
Avoid sudden starts or erratic
driving maneuvers which would
place excessive stress on the
emergency towing hook and
towing cable or chain. The hook
and towing cable or chain may
break and cause serious injury
or damage.
If the towing vehicle can hardly
move, do not forcibly continue
the towing. Contact an
Authorized Kia dealer or a
commercial tow truck service
for assistance.
Tow the vehicle as straight
ahead as possible.
Keep away from the vehicle
during towing.
MMSA6011
MS-CNA-Eng 6.QXD 7/25/2005 5:13 PM Page 17
Page 173 of 225

CHANGING TIRESJACKING INSTRUCTIONSThe jack is provided for emergency tire
changing only. Follow jacking
instructions to reduce the possibility of
personal injury.
TIRE REPLACEMENT1. Park on a level surface and set the
parking brake firmly.
2. Set the automatic transaxle in P
(Park), or shift the manual transaxle
into R (Reverse).
3. Activate the hazard warning flasher.
4. Remove the wheel lug nut wrench,
jack, jack handle, and spare tire from
the vehicle.
5. Block both the front and rear of the
wheel that is diagonally opposite the
jack position.
IN CASE OF EMERGENCY
6-22
MMSA6015Flat tire
Wheel block
WARNING - Changing
Tires
Never attempt vehicle repairs
or a tire change in the traffic
lanes of a public road or
highway. Always move the
vehicle completely off the
road and onto the shoulder
before trying to change a tire.
If you cannot find a firm, level
place off the road, call a
towing service company for
assistance.
Be sure to use the correct
front or rear jacking
positions on the vehicle;
never use the bumpers or
any other part of the vehicle
for jack support.
Never allow any portion of
your body to get beneath the
vehicle while using the jack.
Do not start or run the engine
while the vehicle is
supported by the jack.
MS-CNA-Eng 6.QXD 7/25/2005 5:13 PM Page 22
Page 175 of 225

10. Remove the lug nuts by turning them
counterclockwise, then remove the
wheel.
11. Mount the spare tire into position and
tighten the nuts by hand. Install the
lug nuts with the beveled edge
inward.
12. Turn the jack handle counterclockwise
and lower the vehicle until it touches
the ground.
Tighten the lug nuts firmly in an “X”
pattern.Once the lug nuts have been tightened,
lower the vehicle fully to the ground and
continue to tighten the lug nuts until they
are completely secured.
If you are unsure of the tightness of the
wheel lug nuts, have them checked at the
nearest service station. The specified
tightening torque is 76 ft. lb (103 N·m).
IN CASE OF EMERGENCY
6-24
1
3
2
4
MMSA6019
MMSA6018
Jack handle
CAUTION
Your vehicle has metric threads on
the wheel studs and nuts. During
wheel removal, make certain that
the same nuts removed are
reinstalled - or, if replaced, that
nuts with metric threads and the
same configuration are used.
Installation of a non-metric thread
nut on a metric stud or vice-versa
will not secure the wheel to the hub
properly and will damage the stud
so that it must be replaced. Note
that most U.S. lug nuts do not have
metric threads. Be sure to use
extreme care in checking for thread
style before installing aftermarket
lug nuts or wheels. If in doubt,
consult an Authorized Kia Dealer.
Damaged studs may result in wheel
loss and personal injury.
MS-CNA-Eng 6.QXD 7/25/2005 5:13 PM Page 24
Page 177 of 225

MAINTENANCE
7-1
MAINTENANCEMaintenance Services . . . . . . . . . . . . . . . . . . . . . . . . . . .7-2
Maintenance Schedule . . . . . . . . . . . . . . . . . . . . . . . . . .7-3
Owner Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-8
Engine Compartment . . . . . . . . . . . . . . . . . . . . . . . . . .7-10
Engine Oil and Oil Filter . . . . . . . . . . . . . . . . . . . . . . . .7-12
Engine Cooling System . . . . . . . . . . . . . . . . . . . . . . . . .7-14
Brakes and Clutch . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-17
Parking Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-18
Power Steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-18
Automatic Transaxle . . . . . . . . . . . . . . . . . . . . . . . . . . .7-19
Lubricants and Fluids . . . . . . . . . . . . . . . . . . . . . . . . . .7-20
Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-21
Wiper Blades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-22
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-23
Tires and Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-25
Bulb Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-32
Lubricant Specifications . . . . . . . . . . . . . . . . . . . . . . . .7-36
Exterior Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-38
Interior Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-40
Headlight Aiming Adjustment . . . . . . . . . . . . . . . . . . .7-42
7
MS-CNA-Eng 7.QXD 7/25/2005 5:09 PM Page 1
Page 178 of 225

MAINTENANCE
7-2MAINTENANCE SERVICESYou should exercise the utmost care to
prevent damage to your vehicle and/or
injury to yourself whenever performing
any maintenance or inspection procedures.
Should you have any doubts concerning
the inspection or servicing of your vehicle,
we strongly recommend that you have an
Authorized Kia Dealer this work.
An Authorized Kia Dealer has factory-
trained technicians and genuine Kia parts
to service your vehicle properly. For
expert advice and quality service, see an
Authorized Kia Dealer.
Inadequate, incomplete or insufficient
servicing may result in operational
problems with your vehicle that could lead
to vehicle damage, an accident or personal
injury.
OWNER’S RESPONSIBILITYMAINTENANCE SERVICE AND
RECORD RETENTION ARE THE
OWNER’S RESPONSIBILITY.You should retain documents to show that
proper maintenance has been performed
on your vehicle in accordance with the
scheduled maintenance service charts
shown on the following pages. You need
this information to be able to establish
your compliance with the servicing and
maintenance requirements of your Kia
warranties.
Detailed warranty information is provided
in your Warranty Information Manual.
Repairs and adjustments required as a
result of improper maintenance or a lack
of required maintenance are not covered.We recommend that such maintenance be
performed by an Authorized Kia Dealer
using genuine Kia parts. However, such
maintenance may be performed by any
competent automotive repair
establishment using automotive parts
equivalent to those with which your
vehicle or engine was originally equipped.
Whenever we recommend that you have
service or maintenance performed by an
Authorized Kia Dealer, you may have a
competent automotive repair est-
ablishment using proper parts perform
that work as well.
MS-CNA-Eng 7.QXD 7/25/2005 5:09 PM Page 2
Page 184 of 225

MAINTENANCE
7-8OWNER MAINTENANCEOWNER MAINTENANCE
SCHEDULEA qualified service technician should
perform these vehicle inspections at the
indicated intervals to ensure safe and
dependable operation.
Bring any problem to the attention of an
Authorized Kia Dealer as soon as
possible.WHEN REFUELING, CHECK:• Engine oil level
• Engine coolant level
• Brake and clutch fluid level
• Washer fluid level
AT LEAST MONTHLY• Tire inflation pressuresEVERY 6 MONTHS, CHECK:• Power steering fluid level
• Automatic transaxle fluid level
You can do the following scheduled
maintenance items if you have some
mechanical ability, a few basic tools and
if you closely follow the directions in
this manual.OWNER MAINTENANCE
PRECAUTIONSImproper or incomplete service may
result in problems. This section gives
instructions only for the maintenance
items that are easy to perform.As explained earlier in this section, several
procedures can be done only by a qualified
service technician with special tools.
Improper owner maintenance during the
warranty period may affect warranty
coverage. For details, read the separate
Kia Warranty and Consumer Information
Manual provided with the vehicle. If
you’re unsure about any servicing or
maintenance procedure, have it done by
an Authorized Kia Dealer.
CAUTION
Be careful when checking your
engine coolant level. The engine
compartment will be hot and you
could be burned.
WARNING - Maintenance
Work
Performing maintenance work
on a vehicle can be dangerous.
You can be seriously injured
while performing some
maintenance procedures. If you
lack sufficient knowledge,
experience or the proper tools
and equipment to do the work,
have it done by a qualified
technician.
MS-CNA-Eng 7.QXD 7/25/2005 5:09 PM Page 8