lock KIA Magnetis 2006 2.G Manual PDF

7-23
1. Raise the wiper arm and turn the
wiper blade assembly to expose the
plastic locking clip.
Compress the clip and slide the blade
assembly toward the windshield, then
slide it off the arm.2. Firmly grasp the end of the rubber
blade and pull until the tabs are free
of the metal support.
3. Remove the metal retainers from the
rubber blade and install them in the
new rubber blade.
4. Carefully insert a new rubber blade
and re-install the blade assembly in
the reverse order of removal.
Install the blade with the tabs facing
towards the bottom of the wiper arm.
BATTERY
MMSA7014
MMSA7017
✻
NOTICE
Do not allow the wiper arm to fall
against the windshield.
✻
NOTICE
Do not bend the metal retainers.
WARNING
- Battery
dangers
Always read the following
instructions carefully
when handling a battery.Keep lighted cigarettes and
all other flames or sparks
away from the battery.Hydrogen, which is a
highly combustible gas, is
always present in battery
cells and may explode if ignited.If any electrolyte gets
into your eyes, flush
your eyes with clean
water for at least 15 minutes
and get immediate medical
attention. If possible, continue
to apply water with a sponge or
cloth until medical attention is
received. If electrolyte gets on
your skin, thoroughly wash the
contacted area. If you feel a
pain or a burning sensation, get
medical attention immediately.
(Continued)
MS-CNA-Eng 7.QXD 7/25/2005 5:09 PM Page 23

MAINTENANCE
7-32WHEEL REPLACEMENTWhen replacing the metal wheels for any
reason, make sure the new wheels are
equivalent to the original factory units in
diameter, rim width and offset.
BULB REPLACEMENTHEADLIGHT BULB
REPLACEMENT
1. Remove the headlight bulb cover by
turning it counterclockwise.
2. Disconnect the headlight bulb
electrical connector.
MMSA7024
CAUTION
A wheel that is not the correct size
may adversely affect wheel and
bearing life, braking and stopping
abilities, handling characteristics,
ground clearance, body-to-tire
clearance, snow chain clearance,
speedometer calibration, headlight
aim and bumper height.
WARNING - Halogen
Bulbs

Wear eye protection when
changing a bulb. Allow the
bulb to cool before handling it.
Halogen bulbs contain
pressurized gas. If broken, a
halogen bulb will explode and
will produce flying pieces of
glass.
Always handle halogen bulbs
carefully to avoid scratches
and abrasions. If the bulbs
are lit, avoid contact with
liquids. Never touch the
glass with bare hands.
Residual oil may cause the
bulb to overheat and burst
when lit. A bulb should be
operated only when installed
in the headlight assembly.
If a bulb becomes damaged
or cracked, replace it
immediately and carefully
dispose it.
MS-CNA-Eng 7.QXD 7/25/2005 5:09 PM Page 32

7-33
3. Unsnap the headlight bulb retaining
wire.
4. Remove the bulb from the three (3)
slots on the headlight assembly.
5. Install a new headlight bulb in the
three (3) slots on the headlight
assembly and snap the headlight bulb
retaining wire into position.
6. Connect the headlight bulb electrical
connector.
7. Install the headlight bulb cover by
turning it clockwise.
FRONT TURN SIGNAL / POSITION
LIGHT BULB REPLACEMENT1. Remove the bolts from the headlight
assembly.
2. Remove the dust cover.
3. Disconnect the light connector.
4. Remove the light bulb.
5. Insert a new bulb and then connect
the light connector.
6. Install the dust cover and then re-
install the headlight assembly.
FRONT FOG LIGHT
REPLACEMENT (IF EQUIPPED)1. Turn the bulb socket counter-
clockwise and remove the bulb
socket.
2. Insert a new bulb in socket.
3. Install the bulb socket.
MMSA7025
MMSA7026
1. Position light/Turn signal light
2. Headlight
3. Headlight
MMSA7027
1
2
3
MS-CNA-Eng 7.QXD 7/25/2005 5:09 PM Page 33

MAINTENANCE
7-34REAR COMBINATION LIGHT
BULB REPLACEMENT 1. Using a cross-tip screwdriver,
remove the cover.
2. Turn the bulb socket counterclock-
wise and remove it from the housing.
3. Push the bulb in, then rotate it one-
quarter turn counterclockwise and
remove the bulb from the socket.4. Insert a new bulb in the socket, then
push the bulb in and rotate it one-
quarter turn clockwise to lock the
bulb in place.
5. Re-install the bulb socket into the
rear combination light assembly and
rotate it one-quarter turn clockwise to
lock the socket in place.
6. Re-install the cover.
DOME LIGHT BULB
REPLACEMENT1. Using a flat-blade screwdriver,
gently pry the lens from the dome
light housing.
2. Carefully pull the bulb out of the
socket.
3. Insert a new bulb in the socket.
4. Align the lens tabs with the dome
light housing notches and snap the
lens into place.
MMSA7028
O
F
FDOORON
MMSA7035
MS-CNA-Eng 7.QXD 7/25/2005 5:09 PM Page 34

7-35
LICENSE PLATE LIGHT
BULB REPLACEMENT1. Using a Phillips screwdriver, remove the
two (2) lens mounting screws and the lens.
2. Rotate socket one-quarter turn
counterclockwise and carefully pull
the socket from the housing.
3. Carefully pull the bulb out of the socket.
4. Insert a new bulb in the socket.
5. Carefully insert the socket into the
housing and rotate it one-quarter turn
clockwise.
6. Re-install the lens and the two (2)
mounting screws.
CENTER HIGH-MOUNTED
STOPLIGHT BULB
REPLACEMENT1. Remove the cover and turn the bulb
socket counterclockwise and remove
it from the housing.
2. Push the bulb in, then rotate it one-
quarter turn counterclockwise and
remove the bulb from the socket.
3. Insert a new bulb in the socket, then
push the bulb in and rotate it one-
quarter turn counterclockwise and
remove the bulb from the socket.4. Re-install the bulb socket into the
cover and rotate it one-quarter turn
clockwise to lock the socket in place.
5. Re-install the cover.
MMSA7029
MMSA7030
MS-CNA-Eng 7.QXD 7/25/2005 5:09 PM Page 35

9
INDEX
9-1
A
ir Bag - Supplemental Restraint System ................................3-42
Air Cleaner ..................................................................................7-21
Antenna .......................................................................................3-68
Automatic Heating and Cooling Control System .......................4-47
Automatic Transaxle ............................................................4-7, 7-19
B
attery.......................................................................................7-23
Before Driving ..............................................................................5-4
Brake System ..............................................................................4-12
Brakes and Clutch .......................................................................7-17
Bulb Replacement .......................................................................7-32
C
hanging tires ..........................................................................6-22
Climate Control System ..............................................................4-42
Cruise Control .............................................................................4-37
Cup Holders and Console Storage Compartment .......................3-63
D
oor Locks .................................................................................3-9
E
lectrical Circuit Protection .......................................................6-7
Emergency Starting .......................................................................6-3
Emission Control System ..............................................................5-3
Engine Compartment ..................................................................7-10
Engine Cooling System...............................................................7-14
Engine Oil and Oil Filter .............................................................7-12
Exterior Care ...............................................................................7-38
F
uel Filler Lid ...........................................................................3-55
Fuel Requirements ........................................................................5-2
G
auges ......................................................................................4-20
H
eadlight Aiming Adjustment .................................................7-42
Homelink® Wireless Control System.........................................5-12
Hood ............................................................................................3-54
How To Use This Manual .............................................................1-2
If You Have a Flat Tire .............................................................6-19
Ignition Switch ..............................................................................4-2
Immobilizer System ......................................................................3-6
Instrument Cluster .......................................................................4-19
Instrument Panel Overview ...........................................................2-3
Interior and Exterior Overview .....................................................2-2
Interior Care ................................................................................7-40
Interior Features ..........................................................................4-33
Interior Lights .............................................................................3-62K
eyless entry system .................................................................3-4
Keys ..............................................................................................3-3
L
abel Information .....................................................................5-11
Lightings .....................................................................................4-27
Lubricant Specifications .............................................................7-36
Lubricants and Fluids ..................................................................7-20
Luggage Net ................................................................................3-69
Ms-CNA-Eng-INDEX.qxd 7/25/2005 5:07 PM Page 1