ignition KIA OPTIMA PLUG-IN HYBRID 2017 Service Manual

Please note that the TPMS is not a
substitute for proper tire maintenance, and it is the driver’s responsibility to
maintain correct tire pressure, even if
under-inflation has not reached the level to trigger illumination of the TPMS
low tire pressure telltale.
Your vehicle has also been equipped
with a TPMS malfunction indicator to indicate when the system is not oper‐
ating properly. The TPMS malfunction
indicator is combined with the low tire pressure telltale. When the system de‐
tects a malfunction, the telltale will
flash for approximately 1 minute and then remain continuously illuminated.
This sequence will continue upon sub‐
sequent vehicle start-ups as long as the malfunction exists. When the TPMS
malfunction indicator remains illumina‐
ted after blinking for approximately 1 minute, the system may not be able to
detect or signal low tire pressure as in‐
tended. TPMS malfunctions may occur for a va‐
riety of reasons, including the installa‐
tion of replacement or alternate tires
or wheels on the vehicle that prevent the TPMS from functioning properly.
Always check the TPMS malfunction
telltale after replacing one or more tires or wheels on your vehicle to en‐
sure that the replacement or alternate
tires and wheels allow the TPMS to continue to function properly.
NOTICE
If any of the below happens, we rec‐
ommend that the system be
checked by an authorized Kia dealer.
1.The low tire pressure telltale/
TPMS malfunction indicator do
not illuminate for 3 seconds
when the ignition switch is
turned to the ON position or en‐
gine is running.
2.The TPMS malfunction indicator
remains illuminated after blink‐
ing for approximately 1 minute.
3.The Low tire pressure position
telltale remains illuminated.
Low tire pressure position
telltale
-PX
UJSF
QSFTTVSF
UFMMUBMF
8#)
0+'-#
¥
-PX
UJSF
QSFTTVSF
QPTJUJPO
JOGPSNBUJPO
What to do in an emergency
8-10

3. Ensure that button (9) on the com‐pressor is not pressed.
0+')
4. Unscrew the valve cap from thevalve of the flat tire and screw fill‐
ing hose (3) of the sealant bottle
onto the valve.
5. Insert the sealant bottle into the housing (5) of the compressor so
that the bottle is upright.
6. Ensure that the compressor is switched off, position 0.
WARNING
If sealant is dispersed when the in‐jection hose and tire air injectionvalve have not been fully connected,the sealant may overflow and clogthe valve.
0+'"
7. Connect between compressor andthe vehicle power outlet using the
cable and connectors (4).
8. With the engine start/stop button position on or ignition switch posi‐
tion on, switch on the compressor
and let it run for approximately 5~7
minutes to fill the sealant up to
proper pressure. (refer to L

WARNING
nCarbon monoxide
Carbon monoxide poisoning and suf‐focation is possible if the engine isleft running in a poorly ventilated orunventilated location (such as insidea building).
Distributing the sealant
11. Immediately drive approximately7~10 km (4~6 miles or, about 10
min) to evenly distribute the seal‐
ant in the tire.
CAUTION
Do not exceed a speed of 80 km/h(50 mph). If possible, do not fall be‐low a speed of 20 km/h (12 mph).While driving, if you experience anyunusual vibration, ride disturbanceor noise, reduce your speed anddrive with caution until you cansafely pull off of the side of theroad. Call for road side service ortowing.
(Continued)
(Continued)
When you use the Tire Mobility Kit,the tire pressure sensors and wheelmay be stained by sealant. There‐fore, remove the tire pressure sen‐sors and wheel stained by sealantand we recommend to have it in‐spected by an authorized Kia dealer.
Checking the tire inflation
pressure
0+')
1. After driving approximately 7~10 km (4~6 miles, or about 10
minutes), stop at a suitable loca‐
tion. 2. Connect connection hose (10) of
the compressor directly to the tire
valve.
3. Connect between compressor and the vehicle battery using the cable
and connectors.
4. Adjust the tire inflation pressure to 200 kPa (29 psi). With the ignition
switched on, proceed as follows. -
To increase the inflation pres‐sure: Switch on the compressor,
position I. To check the current
inflation pressure setting, briefly switch off the compressor.
WARNING
Do not let the compressor run formore than 10 minutes, otherwisethe device will overheat and may bedamaged.
-To reduce the inflation pressure:
Press the button (9) on the com‐
pressor.

8-19
8
What to do in an emergency

TOWING
Towing service
0+'-
If emergency towing is necessary, we
recommend having it done by an au‐ thorized Kia dealer or a commercial
tow-truck service. Proper lifting and
towing procedures are necessary to prevent damage to the vehicle. The use
of wheel dollies (1) or flatbed is recom‐
mended. It is acceptable to tow the vehicle with
the rear wheels on the ground (without
dollies) and the front wheels off the
ground.
If any of the loaded wheels or suspen‐ sion components are damaged or the
vehicle is being towed with the front
wheels on the ground, use a towing dolly under the front wheels.
When being towed by a commercial
tow truck and wheel dollies are not
used, the front of the vehicle should al‐ ways be lifted, not the rear.
NOTICE
If the EPB does not release normally,
we recommend that you contact an
authorized Kia dealer.
)9%
)9%
CAUTION
•Do not tow the vehicle backwardswith the front wheels on theground as this may cause damageto the vehicle.
•Do not tow with sling-type equip‐ment. Use wheel lift or flatbedequipment.
When towing your vehicle in an emer‐
gency without wheel dollies: 1. Set the ignition switch in the ACC position.

8-21
8
What to do in an emergency

• Use a towing strap less than 5 m(16 feet) long. Attach a white or red
cloth (about 30 cm (12 inches) wide) in the middle of the strap for easy
visibility.
• Drive carefully so that the towing strap is not loosened during towing.
Emergency towing precautions
• Turn the ignition switch to ACC so thesteering wheel isn’t locked.
• Place the transaxle shift lever in N (Neutral).
• Release the parking bake. • Press the brake pedal with more
force than normal since you will have
reduced brake performance.
• More steering effort will be required because the power steering system
will be disabled.
• If you are driving down a long hill, the brakes may overheat and brake per‐formance will be reduced. Stop often
and let the brakes cool off.
CAUTION
nAutomatic transaxle
•If the car is being towed with allfour wheels on the ground, it canbe towed only from the front. Besure that the transaxle is in neu‐tral. Be sure the steering is un‐locked by placing the ignitionswitch in the ACC position. A drivermust be in the towed vehicle tooperate the steering and brakes.
•To avoid serious damage to theautomatic transaxle, limit the ve‐hicle speed to 15 km/h (10 mph)and drive less than 1.5 km (1 mile)when towing.
(Continued)
(Continued)
•Before towing, check the auto‐matic transaxle for fluid leaks un‐der your vehicle. If the automatictransaxle fluid is leaking, flatbedequipment or a towing dolly mustbe used.
What to do in an emergency
8-24

Front windshield wiper blade
0+'
For your convenience, move the wind‐
shield wiper blades to the service posi‐ tion as follows;
After turning off the engine, move the
wiper switch to the single wiping (MIST)
position within 20 seconds and hold the switch more than 2 seconds until the
wiper blade is in the fully up position.
CAUTION
Do not allow the wiper arm to fallagainst the windshield, since it maychip or crack the windshield.
Type A
0).
0).
1. Raise the wiper arm. 2. Lift up the wiper blade clip. Then
pull down the blade assembly and
remove it.
3. Install the new blade assembly.
4. Return the wiper arm on the wind‐ shield.
5. Turn ignition to the ON position and wiper arms will return to the nor‐
mal operating position.
Type B
-%"
1. Raise the wiper arm and turn the wiper blade assembly to expose
the plastic locking clip.

9-37
9
Maintenance

+#"
+#"
2. Compress the clip and slide theblade assembly downward.
3. Lift it off the arm.
4. Install the new blade assembly. 5. Return the wiper arm on the wind‐
shield.
6. Turn ignition to the ON position and wiper arms will return to the nor‐
mal operating position.
Maintenance
9-38

(Continued)
If any electrolyte gets intoyour eyes, flush your eyeswith clean water for atleast 15 minutes and getimmediate medical atten‐tion.If electrolyte gets on yourskin, thoroughly wash thecontacted area. If you feelpain or burning sensation,get medical attention im‐mediately.
Wear eye protection whencharging or working near abattery. Always provideventilation when workingin an enclosed space.
An inappropriately dis‐posed battery can beharmful to the environ‐ment and human health.Dispose the battery ac‐cording to your local law(s)or regulation.
(Continued)
(Continued)
The battery contains lead.Do not dispose of it afteruse. We recommend thatyou contact an authorizedKia dealer.
•When lifting a plastic-cased bat‐tery, excessive pressure on thecase may cause battery acid toleak, resulting in personal injury.Lift with a battery carrier or withyour hands on opposite corners.
•Never attempt to recharge thebattery when the battery cablesare connected.
•The electrical ignition systemworks with high voltage. Nevertouch these components with theengine running or the ignitionswitched on.
Failure to follow the above warningscan result in serious bodily injury ordeath.
CAUTION
•When you don’t use the vehicle fora long time in the low temperaturearea, separate the battery andkeep it indoors.
•Always charge the battery fully toprevent battery case damage inlow temperature area.
•If you connect unauthorized elec‐tronic devices to the battery, thebattery may be discharged. Neveruse unauthorized devices.
Battery capacity label
&YBNQMF
06.-
Maintenance
9-40

NOTICE
The actual fuse/relay panel label
may differ from equipped items.
CAUTION
•When replacing a blown fuse or re‐lay with a new one, make sure thenew fuse or relay fits tightly intothe clips. The incomplete fasteningfuse or relay may cause the vehi‐cle wiring and electric systemsdamage and a possible fire.
•Do not remove fuses, relays andterminals fastened with bolts ornuts. The fuses, relays and termi‐nals may be fastened incomplete‐ly, and it may cause a possible fire.If fuses, relays and terminals fas‐tened with bolts or nuts are blown,we recommend that you consultan authorized Kia dealer.
(Continued)
(Continued)
•Do not input any other objects ex‐cept fuses or relays into fuse/relayterminals such as a driver or wir‐ing. It may cause contact failureand system malfunction.
•Do not plug in screwdrivers or af‐termarket wiring into the terminaloriginally designed for fuse and re‐lays only. The electrical systemand wiring of the vehicle interiormay be damaged or burned due tocontact failure.
Inner panel fuse replacement
0+'
1. Turn the ignition switch and all oth‐er switches off. 2. Open the fuse panel cover.
If the switch is located in the L

If it fits loosely, we recommend that
you consult an authorized Kia dealer.
If you do not have a spare, use a fuse of the same rating from a circuit you
may not need for operating the vehicle,
such as the cigarette lighter fuse.
If the headlights or taillights, stop lights, courtesy lamp, day time running
lights (D.R.L) do not work and the fuses
are OK, check the fuse panel in the en‐ gine compartment. If a fuse is blown, it
must be replaced.
Fuse switch
0+'
Always, put the fuse switch at the ON
position. If you move the switch to the OFF posi‐
tion, some items such as audio and dig‐
ital clock must be reset and transmitter
(or smart key) may not work properly.
If the fuse switch is in OFF, a warning sign will illuminate on the dashboard.
CAUTION
•Put all switches in ON when driv‐ing.
•If the vehicle remains idle for over1 month, put all switches in OFF toprevent the batteries from beingdischarged.
•Excluding long-term parking forover 1 month, the contact pointsof switches may wear out uponextensive use. Please refrain fromexcessive use of switches.
Engine compartment fuse
replacement
1. Turn the ignition switch and all oth‐ er switches off.
2. Remove the fuse panel cover by pressing the tab and pulling the
cover up. When the blade type fuse
is disconnected, remove it by using
the clip designed for changing fuses
located in the engine room fuse
box. Upon removal, securely insert
reserve fuse of equal quantity.
3. Check the removed fuse; replace it if it is blown. To remove or insert
the fuse, use the fuse puller in the
engine compartment fuse panel.
Maintenance
9-54