ABS KIA Rio 2005 2.G Owner's Manual

4-15
3. Press the brake pedal.
4. Depress the lock release button and move the shift
lever.
5. Have your vehicle inspected by an Authorized Kia
Dealership immediately.
AS2B04006A
Brake SystemPower BrakesYour vehicle has power-assisted brakes that adjust
automatically through normal usage.
In the event that brake system power assist is lost
because of a stalled engine or some other reason, you
can still stop your vehicle by applying greater force to
the brake pedal than you normally would. The stopping
distance, however, will be longer.
When the engine is not running, the reserve brake
power is partially depleted each time the brake pedal is
depressed. Do not pump the brake pedal when the
power assist has been interrupted, except when neces-
sary to maintain steering control on slippery surfaces.Anti Lock Brakes (ABS) (if equipped)The anti-lock brake system is designed to prevent lock-
up of the wheels during sudden braking or braking on
slippery surfaces. Compared to a conventional brake
system, the anti-lock brake system provides greater
steering control during braking in such situations.
RIO ENG CNA 4.qxd 7/29/05 5:06 PM Page 15

Driving Your Vehicle4-16
When driving a vehicle equipped with anti-lock brakes,
adjust your driving according to the road and traffic
conditions and keep the following in mind.
 Do not pump the brakes as you would when driving
a vehicle not equipped with an anti-lock brake sys-
tem (ABS). In order for the ABS to function nor-
mally, press the brake pedal firmly, without pump-
ing the pedal.
 Even with the anti-lock brake system, your vehicle
still requires a sufficient stopping distance. Always
maintain a safe distance from the vehicle in front of
you.
 Always slow down when cornering. The anti-lock
brake system cannot prevent accidents resulting
from excessive speeds.
 On loose or uneven road surfaces, operation of the
anti-lock brake system may result in a longer stop-
ping distance than for vehicles equipped with a con-
ventional brake system.
 Avoid high speeds on wet roads. The anti-lock brake
system cannot eliminate the risk of hydroplaning.
If the anti-lock brake system should fail, the brake sys-
tem will function as a conventional brake system. Have
your vehicle checked by an authorized Kia dealer as
soon as possible. During normal driving conditions, the anti-lock brake
system operates the same as a conventional brake sys-
tem. When the anti-lock brake system is engaged due
to imminent loss of traction, a pulsation of the brake
pedal will result and you may hear or feel “chattering”.
This is a normal condition and indicates the system is
functioning properly.
WARNING - ABS Brakes
 The anti-lock brake system (ABS) cannot
compensate for bad road conditions, for
unsafe or reckless driving or for bad judge-
ment.
 The ABS is designed to improve maximum
braking effectiveness on typical highways
and roads in good condition. On road sur-
faces which are in poor condition, the ABS
may actually reduce braking effectiveness.
 Always operate your vehicle at reasonable
speeds that are safe for weather and traffic
conditions.
RIO ENG CNA 4.qxd 7/29/05 5:06 PM Page 16

4-17
✽
NOTICE
 If the ABS warning light is ON and stays ON,
you may have a problem with the ABS system.
In this case, however, your regular brakes will
work normally.
 The ABS warning light will stay ON for 2~3
seconds after the engine starts. During that
time, the ABS will go through self-diagnosis
and the light will go OFF if everything is nor-
mal. If the light stays ON you may have a
problem with your ABS system. Contact an
authorized Kia dealer for service as soon as
possible.✽
NOTICE
 If the battery is discharged and the engine is
jump started, the ABS warning light may come
ON. This condition occurs because of a dis-
charged battery and not because there is an
anti-lock brake system malfunction.
 Have the battery recharged before driving the
vehicle.
AN7B04015
RIO ENG CNA 4.qxd 7/29/05 5:06 PM Page 17

4-33 Door Ajar Warning
This warning light comes on when a door is not closed
securely with the ignition switch in any position.Anti-Lock Brake System (ABS)
Warning Light (if equipped)This light illuminates when you start the engine. The
light will go off if the ABS system is operating nor-
mally. Also, this light comes on if the key is turned to
ON, and then goes off in 2-3 seconds if the system is
operating normally.
If this warning light illuminates while the vehicle is
being driven, have the vehicle checked by an autho-
rized Kia Dealer as soon as possible.Rear Window Defroster Indicator This light comes on when the rear defroster is ON.Rear Hatch Warning Light
(5 door-if equipped)This warning light comes on when a rear hatch is not
closed securely with the ignition switch in any posi-
tion.
AS2B04020
LightingLighting ControlTo turn the lights on, twist the knob on the end of the
control lever which is located on the steering column
to the left of the steering wheel.
First position
Tail, parking, license and sidemarker lights and instru-
ment panel lights ON.
Second position
Head, tail, parking, license and sidemarker lights and
instrument panel lights ON.
ABS
RIO ENG CNA 4.qxd 7/29/05 5:06 PM Page 33

Keeping a vehicle in good operating condition is
important both for economy and safety. Therefore,
have an Authorized Kia Dealer perform scheduled
inspections and maintenance.
Special Driving ConditionsHazardous DrivingWhen hazardous driving is encountered because of
water, snow, ice, mud, sand, or similar hazard, follow
these suggestions:
 Drive cautiously and allow extra distance for
braking.
 Avoid sudden movements in braking or steering.
 When braking in vehicles without anti-lock brakes,
depress the brake pedal with a controlled up-and-
down motion until the vehicle is stopped.
5-7
WARNING - Engine OFF Motion
Never turn the engine OFF to coast down hills
or anytime the vehicle is in motion. The power
steering and power brakes will not function
without the engine running. Instead, downshift
to any appropriate gear for engine braking
effect.
✽
NOTICE
Do not pump the brake pedal on ABS equipped
vehicle.
RIO ENG CNA 5.qxd 7/29/05 5:07 PM Page 7

In Case Of An Emergency6-10Fuse Panel DescriptionDriver’s side kick panel
DESCRIPTION FUSE PROTECTED
RATING COMPONENT
Drive’rs side kick panel
(A/BAG) 10A Airbag
TURN LAMP 10A Turn signal lamp
METER 10A Meterset, Backup lamp,
Warning sound
ILLUMI 10A Illumination
POWER SOCKET 15A Trunk room lamp, Power socket
HAZARD 10A Hazard lamp
STOP 15A Stop lamp, ABS
TAIL(RH) 10A Tail lamp
(Right-Rear/Left-Front),
Switch illumination
TAIL(LH) 10A Tail lamp
(Left-Rear/Right-Front)
CIGAR 15A Cigarette lighter
AUDIO 10A Audio, Electric rearview mirror
WIPER(FRT) 15A Wiper(front), Washer(front),
Sunroof
WIPER(RR) 15A Wiper(Rear), Washer(Rear)
(WARMER) 15A Seatwarmer
MIRROR DEF 10A Mirror defroster
START 10A Engine control unit,
ECAT unit
*( ):Optional
RIO ENG CNA 6.qxd 7/29/05 5:15 PM Page 10

6-11
Engine compartment
DESCRIPTION FUSE PROTECTED
RATING COMPONENT
Engine Compartment
(ABS) 15A ABS
RR FOG 10A Rear fog light (if equipped)
(F/FOG) 15A Front fog light (if equipped)
MAIN 80A Battery is not rechargeable
IG 1 30A (It will be automatically connect
ed to the secondary fuse.) CIGAR
10A, AUDIO 10A, IG COIL 15A,
TURN LAMP 10A, A/BAG 10A,
WIPER(RR) 15A, WIPER(FRT)
15A, RELAY 10A, START 10A
BLOWER 30A Heater
COOLING 30A Cooling fan
(ABS 1) 30A ABS
COND. FAN 20A Condenser fan
HEAD-HI 15A Head lamp high
HEAD-LOW 15A Head lamp low
EMS 10A Engine sensors
INJECTOR 15A Injector, 0
2sensor
F/PUMP 10A Fuel pump
ECU 10A Engine control unit, ECAT unit,
Main relay
RELAY 10A Blower motor, Power window,
Rear window defroster, Head
lamp(Airbag equipped vehicle)
(HLLD) 10A
-
*( ):Optional
STARTWINDOW
POWERFUEL
PUMPFRONT
FOGA/CON
HEAD
LAMPCOOL.FANHORN
TNS MAIN
IG 1 BLOWER
COOL ING(ABS 1) IG 2 COND.F
( )( ) ( )
( )
( )
COND.FAN
ROOM 15A
IG COIL
(ABS)
D/LOCK
BTN
P/WIN
(ABS 2)
RR DEF
HORN
TNS
RR FOG
(HLLD)(F/FOG)
HEAD
S/ROOF
MAIN
RELAY
RELAY
ECU
F/PUMP
INJECT
EMS
HEAD
LOW
HEAD
HI 15A
15A
25A
30A
30A
30A
25A
10A
15A
10A
10A
80A15A
25A
15A
25A
10A
10A
10A
15A
10A
15A
15A
MAIN
30A 30A 30A 30A 30A 20A
* USE THE DESIGNATED FUSE AND RELAY ONLY.
* REFER TO OWNER'S MANUAL FOR FUSE AND RELAY SERVICE.
* ( ) : OPTION
RIO ENG CNA 6.qxd 7/29/05 5:15 PM Page 11

In Case Of An Emergency6-12DESCRIPTION FUSE PROTECTED
RATING COMPONENT
Engine compartment (continued)
MAIN RELAY 25A (It will be automatically connected
to the secondary fuse.)
EMS 10A, INJECTOR 15A,
F/PUMP 10A, ECU 10A
S/ROOF 15A Sunroof
HEAD 25A (It will be automatically connect
ed to the secondary fuse.)
HEAD-HI 15A, HEAD-LOW
15A, FOG LAMP(RR) 10A
IG 2 30A
TNS 15A (It will be automatically connect
ed to the secondary fuse.)
TAIL (LH) 10A, TAIL(RH) 10A
HORN 10A Horn
RR DEF 25A Rear window defroster
(ABS 2) 20A ABS
P/WIN 30A Power window
BTN 30A (It will be automatically connect
ed to the secondary fuse.)
MEMORY/ROOM 10A,
STOP 15A, HAZARD 15A
D/LOCK 25A Power door lock
IG COIL 15A Ignition coil
ROOM 15A Room LAMP, Audio,
Meterset, Warning sound
*( ): Optional
RIO ENG CNA 6.qxd 7/29/05 5:15 PM Page 12

6-13 Memory Fuse (If Equipped)
Your vehicle is equipped with a “Memory Fuse” to
prevent battery discharge if the vehicle is parked for
prolonged periods without being operated. Use the
following procedures before parking the vehicle for a
prolonged period.
1. Turn off the engine.
2. Turn off the headlights and tail lights.
3. Open the main fuse box cover in the engine compartment
and pull up the “ROOM FUSE 15A” using the fuse
puller; push the fuse to the side. This will change the
MEMORY FUSE mode to prevent battery discharge.
FUEL
PUMPFRONT
FOGA/CON
HEAD
LAMPCOOL.FANHORN
TNS MAIN
COND.F( ) ( )
( )
( )
COND.FAN
ROOM 15A
IG COIL
(ABS)(F/FOG)
HEAD 15A
15A15A
25A
20A
* REFER TO OWNER'S MANUAL FOR FUSE AND RELAY SERVICE.
* ( ) : OPTION
RIOMEMORY
CAUTION
•If the memory fuse is pulled up from the fuse
box housing, the radio and dome light will not
operate. After reinstalling the “Memory Fuse”,
the radio “anti-theft”code (Optional) must be
entered again and the preset radio stations
must be reselected.
Even though the memory fuse is pulled up, the
battery can still be discharged by operation of
the headlights or other electrical devices.
RIO ENG CNA 6.qxd 7/29/05 5:15 PM Page 13

1. Raise the wiper arm and turn the wiper blade
assembly to expose the plastic locking clip.
Compress the clip and slide the blade assembly
toward the windshield, then slide it off the arm.
7-29
2. Firmly grasp the end of the rubber blade and pull
until the tabs are free of the metal support.
✻ ✻
NOTICE
Do not allow the wiper arm to fall against the
windshield.
AN7B07016AN7B07017
Plastic locking
clip Push
Metal support
TabsPull out
RIO ENG CNA 7-2.qxd 7/29/05 5:18 PM Page 29