ignition KIA Sorento 2006 1.G Workshop Manual

Fan Speed Control Knob
Four (4) adjustable fan speeds are
provided which increase as the num-
ber increases. The ignition switch
must be in the ON position for fan
operation.
0 - Fan off
1 - Low speed
2 - Medium speed
3 - High speed
4 - Maximum speed Temperature Control Knob
The temperature control knob allows
you to control the temperature of the
air flowing from the ventilation sys-
tem. To change the air temperature in
the passenger compartment turn the
knob to the right for warm and hot air
or left for cooler air.Mode Selection Knob
The mode selection knob controls the
direction of the air flow through the
ventilation system. The air from outlet
port D flows at any mode. Close the
ventilation outlets using the knob to
block the air flow if you do not want
the air.DRIVING YOUR VEHICLE4-72
012
3
4
S1BLA210
PUSHA/C
S1BLA209
PUSH
MAX
A/C
S4BLA472
BL-ENG (CAN)-4.qxd 7/28/05 5:55 PM Page 72

Recirculated air position
If you press the air intake
control button once (recir-
culate), almost all outside
air flow into the vehicle is
shut off, and air within the
vehicle will be recirculated.
This position can be used
temporarily for maximum
heating or cooling (if
equipped with an air condi-
tioning) and to help pre-
vent undesirable outside
air flow into the vehicle.Outside (fresh) air position
If you press the air intake
control button again, the
air position will be changed
to outside (fresh) air and
air will enter the ventilation
system from outside the
vehicle. Use this position
for normal ventilation and
heating.
To reduce the probability of fogging
up the inside of the windshield, the air
intake control is set to the outside
(fresh) air position automatically if
any of following occur.
The mode is selected to the,
or while the system is activated.
The ignition switch is turned off.
The fan is off.
Press the air intake control button to
select the recirculated air position
while the ignition switch is on.
DRIVING YOUR VEHICLE
4-75
CAUTION
Continued climate control sys-
tem operation in the recirculat-
ed air position may allow
humidity to increase inside the
vehicle which may fog the glass
and obscure visibility.
WARNING
Don’t sleep in a vehicle with air
conditioning system or heating
system on. It may cause serious
harm or death to passengers
due to a drop in the oxygen
level and/or body temperature.
BL-ENG (CAN)-4.qxd 7/28/05 5:55 PM Page 75

Fan Speed Control
Button
The fan speed can be set to the
desired speed by pressing the appro-
priate fan speed control button.
The higher the fan speed is, the more
air is delivered.
Pressing the “OFF”button turns off
the fan.
- Fan off
- Low speed
- Medium speed
- High speed
- Maximum speed Air Flow Control Button
This is used to select outside (fresh)
air position or recirculated air posi-
tion.
To change the air intake control posi-
tion, push the control button.
Recirculated air position
The indicator light is illuminated when
the air intake control is in recirculated
air position.
With the recirculated air position
selected, air from passenger com-
partment will be drawn through the
heating system and heated or cooled
according to the function selected.Outside (fresh) air posi-
tion
The indicator light on the button is
illuminated when the air intake con-
trol is set to the outside (fresh) air
position.
With the outside (fresh) air position
selected, air enters the vehicle from
outside and is heated or cooled
according to the function selected.
The system will automatically switch
to the outside (fresh) air position
whenever the ignition is turned ON.
To cancel the automatic outside
(fresh) air selection, refer to the can-
cel procedure in the windshield
defrosting and defogging section.DRIVING YOUR VEHICLE4-82
BL-ENG (CAN)-4.qxd 7/28/05 5:56 PM Page 82

For maximum defrosting, set the
temperature control knob to the
extreme right/hot position and the
fan speed control knob to the high-
est speed.
If warm air to the floor is desired
while defrosting or defogging, set
the mode selection knob to the
floor- defrost position.
Before driving, clear all snow and
ice from the windshield, rear win-
dow, outside rear view mirrors, and
all side windows.
Clear all snow and ice from the
hood and air inlet in the cowl grill to
improve heater and defroster effi-
ciency and to reduce the probabili-
ty of fogging up inside of the wind-
shield.How to cancel automatic outside
(fresh) air position in the Floor,
Floor-Defrost and Defrost posi-
tion:
When you select the Floor, Floor-
Defrost or Defrost position, the out-
side (fresh) air position will be select-
ed automatically.
If you don’t want the outside (fresh)
air position when operating in either
of these modes, you can turn off the
automatic outside (fresh) air position
by performing the following:1. Make sure the engine is running or
the ignition switch is in the ON
position.
2. Turn the fan speed control knob to
the “0”position.
3. Turn the mode selection knob to
the defrost ( ) position.
4. Push the air intake control button
( ) at least 5 times within 3 sec-
onds.
Then the indicator light on the air
intake control button will blink 3
times with 0.5 second intervals
between blinks.
If you want to return to the automatic
outside (fresh) air position, repeat the
procedure above.
DRIVING YOUR VEHICLE
4-87
PUSHMAX
A/C
PUSHMAX
A/C
S4BLA475
BL-ENG (CAN)-4.qxd 7/28/05 5:56 PM Page 87

How to cancel forced air-condition-
ing operation and outside (fresh)
air position in floor-defrost and
defrost position ;
When you select the Floor-Defrost or
Defrost position, the system automat-
ically turns on the air-conditioning
system and the outside (fresh) air
position will be selected.
If you don’t want air-conditioning and
the outside (fresh) air position when
operating in either of these modes,
you can turn off the air-conditioning
system operation by performing the
following:1. Make sure the engine is running or
the ignition switch is in the ON
position.
2. Select the defrost position press-
ing the defrost ( ) button.
3. While holding the air conditioning
button A/C depressed, depress the
recirculated air position button
( ) at least 5 times within 3 sec-
onds.
The indicator light in the recirculat-
ed air position button ( ) will
blink 3 times with 0.5 second of
interval.
If you want to return to the automatic
air conditioning system and outside
(fresh) air position, repeat the proce-
dure above.
Follow the same procedure if you
want to cancel or return to the forced
outside (fresh) air position when you
start the engine with recirculated air
position selected manually before the
engine off.
DRIVING YOUR VEHICLE
4-89
S2BLA478
BL-ENG (CAN)-4.qxd 7/28/05 5:56 PM Page 89

Operating Precautions for
Catalytic Converters
Your vehicle is equipped with a cat-
alytic converter emission control
device.
Therefore, the following precautions
must be observed:
 Use only UNLEADED FUEL.
 Do not operate the vehicle when
there are signs of engine malfunc-
tion, such as misfire or a noticeable
loss of performance.
 Do not misuse or abuse the engine.
Examples of misuse are coasting
with the ignition off and descending
steep grades in gear with the igni-
tion off. Do not operate the engine at high
idle speed for extended periods (5
minutes or more).
 Do not modify or tamper with any
part of the engine or emission con-
trol system. All inspections and
adjustments must be made by a
qualified technician.
Failure to observe these precautions
could result in damage to the catalyt-
ic converter and to your vehicle.
Additionally, such actions could void
your warranties.DRIVING TIPS5-4
WARNING
Your Full-time Four-Wheel Drive
vehicle must never be tested on
a two-wheel dynamometer.
Serious transmission damage
and uncontrolled vehicle move-
ment could result.
WARNING
- Fire
A hot exhaust system can ignite
flammable items under your
vehicle. Do not park the vehicle
over or near flammable objects,
such as dry grass, paper,
leaves, etc.
BL-ENG (CAN)-5.qxd 7/28/05 5:56 PM Page 4

TIPS ON DRIVING YOUR
VEHICLEBefore Entering Vehicle:
 Be sure that all windows, outside
mirror(s), and outside lights are
clean.
 Check the condition of the tires.
 Check under the vehicle for any
sign of leaks.
 Be sure there are no obstacles
behind you if you intend to back up.
Necessary Inspections
Fluid levels, such as engine oil,
engine coolant, brake/clutch fluid,
and washer fluid should be checked
on a regular basis, with the exact
interval depending on the fluid.
Further details are provided in the
“Maintenance” section.Before Starting
 Close and lock all doors.
 Position the seat so that all controls
are easily reached.
 Adjust the inside and outside
rearview mirrors.
 Be sure that all lights work.
 Check all gauges.
 Check the operation of warning
lights when the ignition switch is
turned to the ON position.
 Release the parking brake and
make sure the brake warning light
goes out.
For safe operation, be sure you are
familiar with your vehicle and its
equipment.
DRIVING TIPS
5-5
WARNING- Driving Under the
Influence of Alcohol or
Drugs
Drinking and driving is danger-
ous. Drunk driving is the num-
ber one contributor to the high-
way death toll each year. Even
a small amount of alcohol will
affect your reflexes, percep-
tions and judgement.
You are much more likely to
have a serious accident if you
drink and drive.
If you are drinking or taking
drugs, don’t drive. Do not ride
with a driver who has been
drinking or taking drugs.
Choose a designated driver or
call a cab.
Driving while under the influ-
ence of drugs is as dangerous
or more dangerous than driving
drunk.
BL-ENG (CAN)-5.qxd 7/28/05 5:56 PM Page 5

Driving in the Rain
Rain and wet roads can make driving
dangerous, especially if you’re not
prepared for the slick pavement. Here
are a few things to consider when
driving in the rain:
 A heavy rainfall will make it harder
to see and will increase the dis-
tance needed to stop your vehicle,
so slow down.
 Keep your windshield wiping equip-
ment in good shape. Replace your
windshield wiper blades when they
show signs of streaking or missing
areas on the windshield.
 If your tires are not in good condi-
tion, making a quick stop on wet
pavement can cause a skid and
possibly lead to an accident. Be
sure your tires are in good shape. Turn on your headlights to make it
easier for others to see you.
 Driving too fast through large pud-
dles can affect your brakes. If you
must go through puddles, try to
drive through them slowly.
 If you believe your brakes may have
become wet, apply them lightly
while driving until normal braking
operation returns.Winter Driving
 We recommend that you carry
emergency equipment, including
tire chains, a window scraper, wind-
shield de-icer, a bag of sand or salt,
flares, a small shovel and jumper
cables.
 Make sure you have sufficient eth-
ylene-glycol coolant in the radiator.
 Check the battery condition and
cables. Cold temperatures reduce
the capacity of any battery, so it
must be in excellent condition to
provide enough winter starting
power.
 Make sure the engine oil viscosity
is suitable for cold weather.
 Check the ignition system for loose
connections and damage.DRIVING TIPS5-10
BL-ENG (CAN)-5.qxd 7/28/05 5:56 PM Page 10

Driving in Water
Light rain causes no special off-road
driving problems. However, heavy
rain can cause flash flooding, and
flood waters demand extreme cau-
tion.
Find out how deep the water is before
you drive through it. If it’s deep
enough to cover your wheel bearing
hubs, axles, or exhaust pipe, don’t try
it. You probably won’t get through.
Also, water that deep can damage
your axle and other vehicle parts.If the water isn’t too deep, then drive
through slowly. At fast speeds, water
can splash on your ignition system
and your vehicle can stall. Stalling
can also occur if your tailpipe goes
underwater. As long as your tailpipe
is underwater, you will not be able to
start your engine. When you go
through water, remember that it may
take you longer to stop when your
brakes are wet.
If you have driven through water that
was deep enough to cover your
wheel bearing hubs, it may be a good
idea to have an authorized Kia dealer
repack your front wheel bearings and
examine your rear-end fluid for evi-
dence of water.After Off-Road Driving
Remove any brush or debris that has
collected on the underbody, chassis
or under the hood. These accumula-
tions can be a fire hazard.
After driving in mud or sand, clean
and check the brake linings.
Accumulation of mud or sand can
cause glazing and uneven braking.
Check the body structure, steering,
suspension, wheels, tires, and
exhaust system for damage. Also,
check the fuel lines and cooling sys-
tem for any leakage. Your vehicle will
also require more frequent service
due to off-road use.DRIVING TIPS5-30
BL-ENG (CAN)-5.qxd 7/28/05 5:56 PM Page 30

EMERGENCY STARTINGJump Starting
Jump starting can be dangerous if
done incorrectly. Therefore, to avoid
harm to yourself or damage to your
vehicle or battery, follow the jump
starting procedures on this page. If in
doubt, we strongly recommend that
you have a competent technician or
towing service jump start your vehi-
cle.Jump starting procedure
1. Make sure the booster battery is
12-volt and that its negative termi-
nal is grounded.
2. If the booster battery is in another
vehicle, do not allow the vehicles to
touch.IN CASE OF AN EMERGENCY6-4✽ ✽
NOTICEUse only a 12-volt jumper system.
You can damage a 12-volt starting
motor, ignition system, and other
electrical parts beyond repair by
use of a 24-volt power supply
(either two 12-volt batteries in
series or a 24-volt motor generator
set).
WARNING
- Battery
Never attempt to check the elec-
trolyte level of the battery as
this may cause the battery to
rupture or explode causing seri-
ous injury.
WARNING
- Battery
• Keep all flames or sparks
away from the battery. The
battery produces hydrogen
gas which may explode if
exposed to flame or sparks.
 Do not attempt to jump start
the vehicle if the discharged
battery is frozen or if the elec-
trolyte level is low; the battery
may rupture or explode.
BL-ENG (CAN)-6.qxd 7/28/05 5:57 PM Page 4