ignition KIA Sorento 2006 1.G User Guide

Safety Belt Restraint System
KNOWING YOUR VEHICLE3-26
CAUTION
 When the pre-tensioner safety
belts are activated, a loud
noise may be heard and fine
powder, which may appear to
be smoke, may be visible in the
passenger compartment. The
powder is not toxic.
 The powder may cause skin
irritation and should not be
breathed for prolonged peri-
ods. Wash your hands and face
thoroughly after an accident in
which such powder has been
released.
 If the pre-tensioner seat belt is
not working properly, the airbag
warning light will illuminate,
since both devices are on the
same electrical circuit. If the
SRS airbag warning light does
not blink when the ignition key
is turned to “ON” or “ACC”, or if
it remains illuminated for more
than 6 seconds, or if it illumi-
nates while the vehicle is being
driven, please have an author-
ized Kia dealer inspect the sys-
tem as soon as possible.
WARNING- Pretentioner Repair or
Replacement
 Pre-tensioners are designed
to operate once. After activa-
tion, pre-tensioner safety
belts must be replaced.
 Do not attempt to inspect,
repair or replace the pre-ten-
sioner safety belts yourself.
You can permanently damage
the system.
WARNING
- Safety Belts
To minimize the risk of serious
or fatal injury in an accident, the
driver and all passengers
should use the appropriate
safety restraints for their age
and size. The presence of
airbags does not change the
need to be properly restrained
by a safety belt or size-appro-
priate child restraint. In fact,
airbags can work properly when
passengers are correctly
restrained in the vehicle. Be
sure you are familiar with the
information in this section,
including the information on
infant and child restraints.
Read the safety warnings on the
sun visors.
BL-ENG (CAN)-3.qxd 7/28/05 5:52 PM Page 26

Safety Belt Warning Light and
Chime
Type A
As a reminder to the driver and pas-
senger, safety belt warning light will
illuminate for approximately 6 sec-
onds each time you turn the ignition
switch ON regardless of belt fasten-
ing.
If the driver's safety belt is not fas-
tened when the ignition key is turned
ON, the safety belt warning chime will
sound for approximately 6 seconds.
KNOWING YOUR VEHICLE
3-29
(Continued)
 Wear the lap portion as low as
possible. Be sure that the lap
belt fits snugly around the
hips. never wear a lap belt or
lap portion of a lap/shoulder
belt over your waist; it should
always go over the stronger
area of your hips.
 Never use a single safety belt
for more than one person.
 The seatbacks should always
remain in a comfortable,
upright position when the
vehicle is moving.
(Continued)
 Inspect the safety belts peri-
odically for excessive wear or
damage. Pull out each belt
fully and look for fraying, cuts,
burns or other damage. Pull
the safety belt out and let it
retract a number of times.
Make sure that the lap/shoul-
der belts return smoothly and
easily into the retractor.
 Check the latches to make
sure they latch and release
without interference or delay.
 Never close the doors on any
part of the lap or shoulder
belt.
 Any belt not in good condition
or in good working order
should be promptly replaced.
CAUTION
Never close the doors on any part
of the lap or shoulder belt. It can
damage the safety belt or buckle
which could increase the risk of
injury in case of an accident.
WARNING- Safety Belt Care
 A damaged belt may not give
you the protection you need in
an accident.
(Continued)
W-29
BL-ENG (CAN)-3.qxd 7/28/05 5:52 PM Page 29

Type B
As a reminder to the driver and pas-
senger, safety belt warning light will
blink for approximately 6 seconds
each time you turn the ignition switch
ON regardless of belt fastening.
If the driver's safety belt is unfastened
after the ignition switch is ON, the
safety belt warning light will blink for
approximately 6 seconds.
If the driver's safety belt is not fas-
tened when the ignition key is turned
ON, the safety belt warning chime will
sound for approximately 6 seconds.Front and Rear Outboard
Lap/Shoulder Belt
To fasten the lap/shoulder belt:
1. Grasp the buckle and tongue plate.
2. Slowly pull the lap/shoulder belt
out from the retractor.3. Insert the tongue plate into the
open end of the buckle until an
audible “click”is heard, indicating
the belt is locked in the buckle.KNOWING YOUR VEHICLE3-30
S2BLA371
S2BLA372
BL-ENG (CAN)-3.qxd 7/28/05 5:52 PM Page 30

Airbag system components
The main components of your SRS
are:
To indicate that your vehicle is
equipped with airbags, the corre-
sponding airbag covers are marked
with “SRS AIRBAG”.
- Driver’s airbag (see page 3- 48)
- Passenger’s airbag(see page 3- 49)
- Curtain airbag (see page 3- 55)
A diagnostic system that continual-
ly monitors the system operation.
An indicator light to warn you of a
possible problem with the system.
Emergency power backup in case
your car’s electrical system is dis-
connected in a crash.The SRS uses a collection of sensors
to gather information about the dri-
ver’s and front passenger’s safety
belt usage and impact severity.
The safety belt usage sensors deter-
mine if the driver and front passen-
ger’s safety belts are fastened. These
sensors provide the ability to control
the SRS deployment based on
whether or not the safety belts are
fastened, and how severe is the
impact.
KNOWING YOUR VEHICLE
3-47
(Continued)
 If your vehicle has been sub-
jected to flood conditions
(e.g. soaked carpeting/stand-
ing water on the floor of the
vehicle, etc.) or if your vehicle
has become flood damaged in
any way, do not attempt to
start the vehicle or put the key
in the ignition before discon-
necting the battery. This may
cause airbag deployment,
which could result in serious
personal injury or death. If
flooded conditions are sub-
jected to your vehicle, before
starting the vehicle, have the
vehicle towed to an author-
ized Kia dealer for inspection
and necessary repairs.
BL-ENG (CAN)-3.qxd 7/28/05 5:52 PM Page 47

The advanced SRS offers the ability
to control the airbag inflation with two
levels. A first stage level is provided
for moderate-severity impacts. A sec-
ond stage level is provided for more
severe impacts.
According to the impact severity and
safety belt usage, the SRSCM (SRS
Control Module) controls the airbag
inflation. Failure to properly wear
safety belts can increase the risk or
severity of injury in an accident.
Additionally, your SRS is equipped
with an occupant classification sys-
tem in the front passenger’s seat. The
occupant classification system
detects the presence of a passenger
in the front passenger’s seat and will
turn off the front passenger’s airbag
under certain conditions. For more
detail, see “Occupant Classification
System”later in this section.
Driver’s airbag
The driver’s airbag is stored in the
center of the steering wheel.KNOWING YOUR VEHICLE3-48
WARNING
 Ignoring the SRS indictor light
(airbag indicator and passen-
ger airbag off indicator) can
result in serious or fatal injury
if the airbags occupant classi-
fication system or pretension-
ers do not work properly. Have
your car checked by a dealer
as soon as possible if the SRS
warning light alerts you to a
potential problem.
 Sitting improperly or out of
position can result in serious
or fatal injury in a crash. All
occupants should sit upright
in their seats with their feet on
the floor until the vehicle is
parked and the ignition key is
removed.
SRSAIRBAG
R
E
S
A
C
C
E
LCOAST
SET
P
W
RSEEK
C
A
N
C
E
L
5BLA422HLZ206
BL-ENG (CAN)-3.qxd 7/28/05 5:52 PM Page 48

KNOWING YOUR VEHICLE3-52
WARNING
If the front passenger seat
should be modified for persons
with disabilities that may affect
the operation of the occupant
classification system, contact
an authorized Kia dealer.
WARNING
 Even though your vehicle is
equipped with the occupant
classification system, do not
install a child restraint system
in the front passenger seat.
The child could be severely
injured or killed if the airbag
deploys. Children are afford-
ed the most protection in the
event of an accident when
they are restrained by the
proper restraint system in the
rear seat.
(Continued)
(Continued)
 If the "PASSENGER AIRBAG
OFF" indicator is illuminated
when the front passenger's
seat is occupied by a person of
adult size who is seated prop-
erly, or if the "PASSENGER
AIRBAG OFF" indicator is not
illuminated when the front pas-
senger's seat is unoccupied or
occupied by a very small per-
son, the occupant classifica-
tion system is not working
properly. Have your vehicle
immediately inspected by your
Kia dealer if the occupant clas-
sification system is not work-
ing properly.
(Continued)
CAUTION
If the occupant classification
system is not working properly,
the airbag warning light ( ) on
the instrument panel will illumi-
nate. If there is a malfunction of
the occupant classification sys-
tem, the "PASSENGER AIRBAG
OFF" indicator will illuminate
and the front passenger's
airbag will not deploy in frontal
crashes even if there is an adult
sized occupant in the front pas-
senger seat. If the SRS airbag
warning light does not illumi-
nate when the ignition key is
turned to "ON" position, if it
remains illuminated after blink-
ing for approximately six sec-
onds, or if it illuminates while
the vehicle is being driven, have
an authorized Kia dealer
inspect the occupant classifica-
tion system with the SRS airbag
system as soon as possible.
BL-ENG (CAN)-3.qxd 7/28/05 5:52 PM Page 52

Noise and smoke
When the airbags inflate, they make
a loud noise and they leave smoke
and powder in the air inside of the
vehicle. This is normal and is a result
of the ignition of the airbag inflator.
After the airbag inflates, you may feel
substantial discomfort in breathing
due to the contact of your chest to
both the safety belt and the airbag, as
well as from breathing the smoke and
powder.We strongly urge you to
open your doors and/or windows
as soon as possible after impact in
order to reduce discomfort and
prevent prolonged exposure to the
smoke and powder.
Though smoke and powder are non-
toxic, it may cause irritation to the
skin (eyes, nose and throat etc). If
this is the case, wash and rinse with
the cold water immediately and con-
sult the doctor if the symptom per-
sists.Installing a child restraint on a
front passenger seat is forbidden.
Never place a rear-facing child
restraint in the front passenger seat.
If the airbag deploys, it would impact
the rear-facing child restraint, caus-
ing serious or fatal injury.
In addition, do not place front-facing
child restraint in the front passenger
seat either. If the front passenger
airbag inflates, it would cause serious
or fatal injuries to the improperly posi-
tioned or improperly restrained child.
KNOWING YOUR VEHICLE
3-63
WARNING
When the airbags deploy, the
airbag related parts in steering
wheel and/or instrument panel
and/or in both sides of the roof
rails above the front and rear
doors are very hot. To prevent
injury, do not touch the airbag
storage areas internal compo-
nents immediately after an
airbag has inflated.
ADAIRBAG
BL-ENG (CAN)-3.qxd 7/28/05 5:52 PM Page 63

Airbag warning light
The purpose of airbag warning light
in your instrument panel is to alert
you of a potential problem with your
airbag - Supplemental Restraint
System (SRS).
When the ignition switch is turned
ON, the indicator light should blink or
illuminate for approximately 6 sec-
onds, then go off.
Have the system checked if:
The light does not turn on briefly
when you turn the ignition ON.
The light stays on after the engine
starts.
The light comes on while the vehi-
cle is in motion.Airbag (Supplemental Restraint
System) service
Your Supplemental Restraint System
is virtually maintenance-free. There
are no parts which you can service.
You must have the system serviced
under the following circumstances:
If an airbag ever inflates, the airbag
must be replaced. Do not try to
remove or discard the airbag by
yourself. This must be done by an
authorized Kia dealer.
If the airbag warning indicator light
alerts you to a problem, have the
airbag system checked as soon as
possible. Otherwise, your airbag
system may be ineffective.
KNOWING YOUR VEHICLE3-64
A-BAG-W
WARNING
 Never put child restraint in the
front passenger seat. If the
front passenger airbag
inflates, it would cause seri-
ous or fatal injuries.
 When children are seated in
the rear outboard seats in
which curtain airbags are
equipped, be sure to put the
child restraint system as far
away from the door side as
possible, and secure the child
restraint system to be locked
in position.
Inflation of curtain airbag
could cause serious injury or
death due to the expansion
impact.
BL-ENG (CAN)-3.qxd 7/28/05 5:52 PM Page 64

SUNROOF (IF EQUIPPED)If your vehicle is equipped with this
feature, you can slide or tilt your sun-
roof with the sunroof switches located
on the overhead console.
Sliding the Sunroof
The sunroof can be opened or closed
when the ignition switch is in the “ON”
position. To slide the sunroof,
momentarily press “OPEN”() on
the SLIDE switch. The sunroof will
slide all the way open. To stop the
sunroof sliding at any point, press
any sunroof switch. To close the sun-
roof, press “CLOSE”( ) on the
SLIDE switch and hold it until it is
closed completely.Tilting the Sunroof
To tilt the sunroof, momentarily press
“UP”( ) on the TILT switch. The
sunroof will tilt all the way up. To stop
the sunroof tilting at any point, press
any sunroof switches.
To close it, press “DOWN”() on
the TILT switch and hold it until it is
closed completely.
KNOWING YOUR VEHICLE
3-83
PUSHTILTSLIDE
S2BLA430C
PUSHTILTSLIDE
S2BLA430G
✽ ✽
NOTICEThe sunroof cannot slide when it is
in the tilt position nor can it be tilt-
ed while in an open or slide posi-
tion.
BL-ENG (CAN)-3.qxd 7/28/05 5:52 PM Page 83

Resetting the Sunroof
When your battery happens to be dis-
connected or discharged, or you use
the emergency handle to operate the
sunroof, you have to reset your sun-
roof system as follows:
1. Turn the ignition key to the ON
position
2. Tilt the sunroof up fully as follows:
Case A :When the sunroof has
closed completely or
been tilted:
Press the TILT UP but-
ton for 1 second then
release it.
Case B :When the sunroof has
slid open:
Press and hold the
close button for more
than 5 seconds until the
sunroof has closed com-
pletely, then press the
TILT UP button for 1
second and release it.3. Press and hold the TILT UP button
once again until the sunroof
moves slightly and returns to the
original TILT UP position.
4. Release the TILT Up button when
the procedure is finished. The
sunroof system is reset.
KNOWING YOUR VEHICLE
3-85
PUSHTILTSLIDE
S2BLA738BS2BLA329
BL-ENG (CAN)-3.qxd 7/28/05 5:52 PM Page 85