sensor KIA SORENTO 2015 Features and Functions Guide

77
Electronic Stability Control (ESC)
The ESC system is designed to help stabilize the
vehicle during cornering maneuvers It is a good
idea to keep the ESC turned on for daily driving
whenever possible
Press ESC button A to turn ESC OFF/ON
REMINDER: ESC is turned ON at vehicle start-up
REMINDER: The ESC Indicator Light in the instrument cluster will be lit momentarily whenever the ESC is active
Hill-Start Assist Control (HAC)
HAC helps prevent the vehicle from rolling
backwards when accelerating from a stop
while on a steep incline
The HAC automatically activates whether
the ESC is OFF or ON but does NOT activate
when the ESC has malfunctioned
REMINDER: The HAC does not operate when the gear shift is in the P (Park) or the N (Neutral) position
• When HAC is active (e g , during initial acceleration from a stop on an incline), you may notice that the brakes will momentarily remain engaged after you depress the accelerator
• HAC provides a 2-second delay before the vehicle may start rolling backwards
QUICK TIPS
Blind Spot Detection
(BS D) System*
The system uses a radar sensor to help
alert the driver while driving The BSD
indicator on the button B will illuminate
when turned ON
The system will become active when
the vehicle is traveling more than 19
mph and will alert the driver when
another vehicle is detected by the
radar sensor
1st stage alert: When another vehicle
is detected within the BSD System
boundary, a yellow light will illuminate on
the outside rearview mirrors
2nd stage alert: When 1st stage alert
is on and a turn signal is turned on, the
2nd-stage alert will sound
X
X
X
AB
(Button panel located lef t of Steering Wheel)
Blind Spot Detection Video To view a video on your mobile device, snap this QR Code or visit the listed website
Refer to page 2 for more information
w w w. KuTechVideos .com/xm13/2015
REMINDER: The Blind Spot Detection System is not a substitute for proper and safe driving practices Always drive safely and use caution when changing lanes or backing up The system may not detect every object alongside the vehicle
QR Code
ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPERATING INFORMATION AND SAFET Y WARNINGS. *IF EQUIPPED
DRIVER’S PANELDRIVER’S PANELDRIVER’S PANEL

30
•
• You can reprogram a single HomeLink ® button by repeating Step 2
• Erasing programmed buttons will delete all trained transmitters
QUICK TIPS
The Auto-Dimming Rearview Mirror is designed to help
reduce glare from a vehicle’s headlights located in the
rear and also connect up to three electronic transmitters
in one location
To turn automatic dimming ON or OFF, press button F
HomeLink® with Auto-Dimming
Rearview Mirror*
How to Sync Transmitter with HomeLink®*
Erasing programmed buttons:
A HomeLink® button
B HomeLink® button
C Indicator light
D HomeLink® button
E Glare detection sensor
F Automatic dimming ON/OFF
G Compass control button
If programming for the first time, begin with Step 1
(repeating this step will delete all information)
To program non-rolling and rolling code garage door
openers and other devices:
1 Press and hold the left A and center D buttons
simultaneously until the indicator light C begins to
flash (to reprogram buttons, skip this step)
2 Press and hold the desired button A B D and hold
the button on the transmitter while it is approximately
1 to 3 inches away from the mirror The HomeLink®
Indicator light C will flash rapidly once the frequency
signal has been successfully programmed
To finish programming rolling code garage door openers,
complete these steps:
3 Locate the “learn” or “smart ” button on the garage
door’s motor head unit Press and release the button
and complete Step 4 within 30 seconds
4 Firmly press and release the programmed HomeLink®
button up to three times
Press and hold the left A and center D buttons
simultaneously for approximately 20 seconds,
and then release both buttons within 30 seconds
Operating HomeLink®:
Press one of the programmed HomeLink® buttons REMINDER: Mirror indicator light C will illuminate when automatic dimming is ON
If your garage door opener was manufactured in 2011 or later, and you’re unable to program your vehicle’s HomeLink® system, you may need to purchase a HomeLink® Repeater Kit. For more information, go to www.HomeLink.com or call (800) 355-3515 .
ABCDEFG
SORENTO FEATURES & FUNCTIONS GUIDE
*IF EQUIPPED
OTHER KEY FEATURES