oil KIA STONIC 2018 Service Manual

FUSES
¥
#MBEF
UZQF
¥
$BSUSJEHF
UZQF
¥
.VMUJ


GVTF ¥
#'5
❈Left side : Normal Right side : Blown
A vehicle’s electrical system is protec‐
ted from electrical overload damage by fuses.
This vehicle has 2 (or 3) fuse panels,
one located in the driver’s side panel
bolster, the others in the engine com‐ partment near the battery.
If any of your vehicle’s lights, accesso‐
ries, or controls do not work, check the
appropriate circuit fuse. If a fuse has blown, the element inside the fuse will
melt.
If the electrical system does not work,
first check the driver’s side fuse panel.
Before replacing a blown fuse, discon‐ nect the negative battery cable.
Always replace a blown fuse with one
of the same rating.
If the replacement fuse blows, this indi‐
cates an electrical problem. Avoid using the system involved and immediately
consult a professional workshop. Kia
recommends to consult an authorized Kia dealer/service partner.
Three kinds of fuses are used: blade
type for lower amperage rating, car‐
tridge type, and multi fuse for higher amperage ratings.
WARNING
nFuse replacement
•Never replace a fuse with anythingbut another fuse of the same rat‐ing.
•A higher capacity fuse could causedamage and possibly a fire.
•Never install a wire or aluminumfoil instead of the proper fuseeven as a temporary repair. It maycause extensive wiring damageand a possible fire.
•Do not arbitrarily modify or add-on electric wiring of the vehicle.
CAUTION
Do not use a screwdriver or any oth‐er metal object to remove fuses be‐cause it may cause a short circuitand damage the system.

8-77
8
Maintenance

SymbolFuse rat‐ingCircuit Protected
S10A Glow Plug Relay Unit, Fuel Filter Heater, Oil Level Sensor
E10AECM (Engine Control Module)/PCM (Power train Control Module), Immobilizer Module, Smart Key
Control Module
15A Sunroof Motor
10A Immobilizer Module
10A Key Interlock, Center Facia Switch
SPARE10A Spare
7.5A SLM Unit, BCM (Body Control Module), Smart Key Control Module
SPARE10A Spare
10A SRS (Supplemental Restraint System) Control Module
MODULE17.5A SBR Unit, BCM (Body Control Module), SLM Unit
25A Smart Key Control Module
7.5A Air Conditioner Control Module
15A Multifunction Switch, Rear Wiper Motor, Rear Wiper Relay
20A Multifunction Switch, Wiper Motor, Engine Room Junction Block(Wiper LO Relay)
10APower Outlet Relay, DC-DC Converter, Audio, Audio / Video & Navigation Head Unit, USB Charger,
SLM UNIT, BCM (Body Control Module), Smart Key Control Module, Power Outside Mirror Switch
SPARE20A Spare
7.5A Instrument Cluster
7.5A Instrument Cluster
Maintenance

8-86

Engine room compartment fuse panel (Kappa 1.0L T-GDI Engine (Gasoline))
SymbolFuse ratingCircuit Protected
80A MDPS Unit
ALT150A Fuse - RR DEFOG, ABS1, ABS2, BLOWER
40A Rear Defogger Relay
140A ABS/ESC (Electronic Stability Control) Control
40A ABS/ESC (Electronic Stability Control) Control, Multipurpose Check Connector
40A Air Conditioner Blower Relay
10A Wiper Motor, Multifunction Switch, Wiper LO Relay
10A Cooling Fan Relay
10A Oxygen Sensor (Up), Oxygen Sensor (Down), RCV Control Solenoid Valve
15AECM (Engine Control Module), Oil Control Valve #1, #2, Purge Control Solenoid Valve, Air Condi‐
tioner Clutch Type ECV Relay
10A Head Lamp RH
10A Head Lamp LH
E315A ECM (Engine Control Module)
E415A ECM (Engine Control Module)


8-91
8
Maintenance

SymbolFuse ratingCircuit Protected
IGN
COIL20A Ignition Coil #1~#4
INJECTOR15A Fuel Pump Relay, ECM (Engine Control Module)
10A Back-Up Lamp Switch
40A Instrument Panel Junction Block
50A Instrument Panel Junction Block (Power Window Relay)
40A Ignition Switch, PDM Relay Box (IG2 Relay)
60A Cooling Fan Relay
30A Fuse - ENG E3, ENG E4, Main Relay
10A Air Conditioner Clutch Type ECV Relay
20A Head Lamp Relay
20A Head Lamp High Relay
FUEL
PUMP20A Fuel Pump Relay
15A Horn Relay, Burglar Alarm Horn Relay
AMS10A Battery Sensor
40A Instrument Panel Junction Block (Tail Lamp Relay)
40A Ignition Switch, PDM Relay Box (IG1 Relay, ACC Relay)
Maintenance
8-92

Engine room compartment fuse panel
(Kappa 1.2L MPI Engine (Gasoline))
SymbolFuse ratingCircuit Protected
80A MDPS Unit
ALT150A 125AFuse - RR DEFOG, ABS1, ABS2, BLOWER
40A Rear Defogger Relay
140A ABS/ESC (Electronic Stability Control) Control
40A ABS/ESC (Electronic Stability Control) Control, Multipurpose Check Connector
40A Air Conditioner Blower Relay
10A Wiper Motor, Multifunction Switch, Wiper LO Relay
10A Cooling Fan1 Relay, Cooling Fan2 Relay
10A Oxygen Sensor (Up), Oxygen Sensor (Down), Front Wheel Sensor RH, Engine Coolant Stop Valve
15AECM (Engine Control Module), Oil Control Valve #1, #2, Purge Control Solenoid Valve, Air Condi‐
tioner Clutch Type ECV Relay
10A Head Lamp RH
10A Head Lamp LH
IGN
COIL20A Ignition Coil #1~#4, Condenser
INJECTOR15A Fuel Pump Relay, ECM, Injector #1~#4
Maintenance
8-94

Engine room compartment fuse panel
(Kappa 1.4L MPI Engine (Gasoline))
SymbolFuse ratingCircuit Protected
80A MDPS Unit
ALT150A 125AFuse - RR DEFOG, ABS1, ABS2, BLOWER
40A Rear Defogger Relay
140A ABS/ESC (Electronic Stability Control) Control
40A ABS/ESC (Electronic Stability Control) Control, Multipurpose Check Connector
40A Air Conditioner Blower Relay
10A Wiper Motor, Multifunction Switch, Wiper LO Relay
10A Cooling Fan1 Relay, Cooling Fan2 Relay
10AOxygen Sensor (Up), Oxygen Sensor (Down), Front Wheel Sensor RH, Engine Coolant Stop Valve
(M/T), Variable Intake Solenoid Valve (M/T)
15AECM/PCM, Engine Coolant Stop Valve (A/T), Oil Control Valve #1, #2 (M/T), Variable Intake Sole‐
noid Valve (A/T), Purge Control Solenoid Valve (M/T), A/C Blower Relay
10A Head Lamp RH
10A Head Lamp LH
IGN
COIL20A Ignition Coil #1~#4, Condenser

8-97
8
Maintenance

SymbolFuse ratingCircuit Protected
INJECTOR15AFuel Pump Relay, ECM/PCM, Injector #1~#4, Oil Control Valve #1, #2 (A/T), Purge Control Sole‐
noid Valve (A/T)
10A Back-Up Lamp Switch
40A Instrument Panel Junction Block
50A Instrument Panel Junction Block (Power Window Relay)
40A Ignition Switch, PDM Relay Box (IG2 Relay)
40A Cooling Fan1 Relay, Cooling Fan2 Relay
30A Main Relay
10A Air Conditioner Clutch Type ECV Relay
20A PCM (A/T)
20A Head Lamp Relay
20A Head Lamp High Relay
FUEL
PUMP20A Fuel Pump Relay
15A Horn Relay, Burglar Alarm Horn Relay
E315A ECM/PCM
AMS10A Battery Sensor
40A Instrument Panel Junction Block (Tail Lamp Relay)
Maintenance
8-98

SymbolRelay NameType
A/C Blower RelayMICRO
Engine room compartment fuse panel
(U-II 1.4L/1.6L Engine (Diesel))
SymbolFuse ratingCircuit Protected
80A MDPS Unit
ALT150A Fuse - RR DEFOG, ABS1, ABS2, BLOWER
40A Rear Defogger Relay
140A ABS/ESC (Electronic Stability Control) Control
40A ABS/ESC (Electronic Stability Control) Control, Multipurpose Check Connector
40A Air Conditioner Blower Relay
10A Wiper Motor, Multifunction Switch, Wiper LO Relay
10A PM Sensor, Electronic VGT Actuator, WGT Vacuum Modulator
10A Lambda Sensor #1, #2, Rail Pressure Regulating Valve, Cooling Fan1 Relay, Cooling Fan2 Relay
15A Camshaft Position Sensor, Air Flow Sensor, Oil Control Valve, PTC1 Heater Relay
10A Head Lamp RH
10A Head Lamp LH
Maintenance
8-100

WARNING
nHalogen bulbs
•Halogen bulbs contain pressurizedgas that will produce flying piecesof glass if broken.
•Always handle them carefully, andavoid scratches and abrasions. Ifthe bulbs are lit, avoid contactwith liquids. Never touch the glasswith bare hands. Residual oil maycause the bulb to overheat andburst when lit.A bulb should be operated onlywhen installed in a headlight.
•If a bulb becomes damaged orcracked, replace it immediatelyand carefully dispose of it.
•Wear eye protection when chang‐ing a bulb. Allow the bulb to cooldown before handling it.
Front turn signal lamp bulb
replacement (Headlamp Type A)
0:##
1. Open the hood.
2. Remove the bulb-socket from theheadlamp assembly by turning the
bulb-socket counterclockwise until
the tabs on the bulb-socket align
with the slots on the headlamp as‐
sembly.
3. Remove the bulb from the bulb- socket by pressing it in and rotat‐
ing it counterclockwise until the tabs on the bulb align with the slots
in the bulb-socket. Pull the bulb out
of the bulb-socket. 4. Insert a new bulb by inserting it in‐
to the bulb-socket and rotating it
until it locks into place.
5. Install the socket in the headlamp assembly by aligning the tabs on
the bulb-socket with the slots in
the assembly. Push the bulb-sock‐
et into the headlamp assembly and
turn the socket clockwise.
Position lamp / Day time
running lamp bulb replacement
(Headlamp Type A)
0:##
1. Open the hood.
Maintenance
8-110

WARNING
nHalogen bulbs
•Halogen bulbs contain pressurizedgas that will produce flying piecesof glass if broken.
•Always handle them carefully, andavoid scratches and abrasions. Ifthe bulbs are lit, avoid contactwith liquids. Never touch the glasswith bare hands. Residual oil maycause the bulb to overheat andburst when lit.A bulb should be operated onlywhen installed in a headlight.
•If a bulb becomes damaged orcracked, replace it immediatelyand carefully dispose of it.
•Wear eye protection when chang‐ing a bulb. Allow the bulb to cooldown before handling it.
Front turn signal lamp bulb
replacement (Headlamp Type B)
0:##
1. Open the hood.
2. Remove the bulb-socket from theheadlamp assembly by turning the
bulb-socket counterclockwise until
the tabs on the bulb-socket align
with the slots on the headlamp as‐
sembly.
3. Remove the bulb from the bulb- socket by pressing it in and rotat‐
ing it counterclockwise until the tabs on the bulb align with the slots
in the bulb-socket. Pull the bulb out
of the bulb-socket. 4. Insert a new bulb by inserting it in‐
to the bulb-socket and rotating it
until it locks into place.
5. Install the socket in the headlamp assembly by aligning the tabs on
the bulb-socket with the slots in
the assembly. Push the bulb-sock‐
et into the headlamp assembly and
turn the socket clockwise.
Static bending light replacement
(Headlamp Type B)
0:##
1. Open the hood.
2. Remove the headlamp bulb cover by turning it counterclockwise.
Maintenance
8-112