air condition KIA STONIC 2018 Workshop Manual

Normal Maintenance Schedule - For Diesel Engine [For Europe (Except Russia)] (continued)
MAINTENANCE INTERVALS
Normal Maintenance Schedule - For Diesel Engine [For Europe (Except Russia)]
Number of months or driving distance, whichever comes first
Months24487296120144168192
Miles×1,00020406080100120140160
Km×1,000306090120150180210240
MAINTENANCE ITEM
Engine oil and engine oil filter *1 ,*2 U-II 1.4L, U-II
1.6L R R R R R R R R
Coolant (Engine) *3
At first, Replace 210,000 km (140,000 miles) or 120 months
after that, Replace every 30,000 km (20,000 miles) or 24 months
Drive belts (Engine) *4
At first, Inspect 90,000 km (60,000 miles) or 48 months
after that, Inspect every 30,000 km (20,000 miles) or 24months
Automatic transaxle fluid - I - I - I - I Manual transaxle fluid *5
- I - I - I - I
Drive shaft and boots I I I I I I I IFuel filter cartridge (Diesel) *6
I R I R I R I R
Fuel lines, hoses and connections I I I I I I I I
Air cleaner filter I R I R I R I R
Exhaust system I I I I I I I I
Cooling system At first, Inspect 60,000 km (40,000 miles) or 48 months
after that, Inspect every 30,000 km (20,000 miles) or 24 months
Air conditioner compressor/refrigerant I I I I I I I I
Maintenance
8-30

MAINTENANCE INTERVALS
Normal Maintenance Schedule - For Diesel Engine [For Europe (Except Russia)]
Number of months or driving distance, whichever comes first
Months24487296120144168192
Miles×1,00020406080100120140160
Km×1,000306090120150180210240
MAINTENANCE ITEM
Climate control air filter R R R R R R R R
Brake discs and pads I I I I I I I I
Brake drums and linings I I I I I I I I
Brake lines, hoses and connections I I I I I I I I
Brake/clutch fluid R R R R R R R R
Parking brake I I I I I I I I
Steering gear rack, linkage and boots I I I I I I I I
Suspension ball joints I I I I I I I I
Tire (pressure & tread wear) I I I I I I I I
Battery condition I I I I I I I I
I : Inspect and if necessary, adjust, correct, clean or replace.
R : Replace or change.


8-31
8
Maintenance

Maintenance Under Severe Usage Conditions - For Diesel Engine [For Europe (Except Russia)]
MAINTENANCE ITEMMAINTENANCEOPERATIONMAINTENANCE INTERVALSDRIVING CONDI‐TION
Engine oil and engine oil filter R Every 15,000 km (10,000 miles) or 12 months A, B, C, D, E, F, G,
H, I, J, K
Automatic transaxle fluid R Every 90,000 km (60,000 miles) A, C, D, E, F, G, H, I,
J
Manual transaxle fluid R Every 120,000 km (80,000 miles) C, D, E, F, G, H, I, J
Drive shaft and boots I Inspect more frequently depending on the con‐
dition C, D, E, F, G, H, I, J
Air cleaner filter R Replace more frequently depending on the con‐
dition C, E
Climate control air filter R Replace more frequently depending on the con‐
dition C, E, G
Brake discs and pads, calipers and ro‐ tors IInspect more frequently depending on the con‐
dition C, D, E, G, H
Brake drums and linings I Inspect more frequently depending on the con‐
dition C, D, E, G, H
Parking brake I Inspect more frequently depending on the con‐
dition C, D, G, H
Steering gear rack, linkage and boots I Inspect more frequently depending on the con‐
dition C, D, E, F, G
Suspension ball joints I Inspect more frequently depending on the con‐
dition C, D, E, F, G
Maintenance operation
I : Inspect and if necessary, adjust, correct, clean or replace.
Maintenance

8-32

Normal Maintenance Schedule - For Diesel Engine [Except Europe (Including Russia)]
The following maintenance services must be performed to ensure good emission control and performance. Keep receipts for
all vehicle emission services to protect your warranty. Where both mileage and time are shown, the frequency of service is determined by whichever occurs first.
NO.ITEMREMARK
*1 Engine oil and engine oil filter Check the engine oil level and leak every 500 km (350 miles) or before start‐ ing a long trip.
*2 Engine oil and engine oil filter (For
Diesel Engine) • The engine oil level should be checked regularly and maintained properly.
Operating with an insufficient amount oil can damage the engine, and suchdamage is not covered by warranty.
• This maintenance schedule depends on fuel quality. It is applicable only when using a qualified fuel <"EN590 or equivalent">. If the diesel fuel speci‐fications don't meet the EN590, it must be replaced according to the severe
maintenance schedule.
*3 Coolant (Engine) When adding coolant, use only deionized water or soft water for your vehicle
and never mix hard water in the coolant filled at the factory. An improper
coolant mixture can result in serious malfunction or engine damage.
*4 Drive belts (Engine) • Adjust alternator, water pump and air conditioner (if equipped) drive belt.
Inspect and if necessary repair or replace.
• Inspect drive belt tensioner, idler and alternator pulley and if necessary cor‐ rect or replace.
*5 Manual transaxle fluid Manual transaxle fluid should be changed anytime it has been submerged in
water.
Maintenance

8-34

MAINTENANCE IN‐TERVALS
Normal Maintenance Schedule - For Diesel Engine [Except Europe (Including Russia)]
Number of months or driving distance, whichever comes first
Months1224364860728496
Miles×1,0001020304050607080
Km×1,000153045607590105120
MAINTENANCE ITEM
Exhaust system - I - I - I - I
Cooling system At first, Inspect 60,000 km (40,000 miles) or 48 months
after that, Inspect every 30,000 km (20,000 miles) or 24 months
Air conditioner compressor/refrigerant I I I I I I I I
Climate control air filter Except Australia andNew Zealand
R R R R R R R R
For Australia and NewZealand I R I R I R I R
Brake discs and pads I I I I I I I I
Brake drums and linings - I - I - I - I
Brake lines, hoses and connections I I I I I I I I
Brake/clutch fluid I R I R I R I R
Parking brake - I - I - I - I
Steering gear rack, linkage and boots I I I I I I I I
Suspension ball joints I I I I I I I I
Tire (pressure & tread wear) I I I I I I I I
Battery condition I I I I I I I I

8-37
8
Maintenance

Maintenance Under Severe Usage Conditions - For Diesel Engine [Except Europe (Including Russia)]
MAINTENANCE ITEMMAINTENANCEOPERATIONMAINTENANCE INTERVALSDRIVING CONDI‐TION
Engine oil and en‐ gine oil filter For Russia, Australiaand New Zealand
R Every 7,500 km (5,000 miles) or 6 months A, B, C, D, E, F, G,
H, I, J, K
Except Russia, Aus‐tralia and New Zea‐land R Every 5,000 km (3,000 miles) or 6 months
A, B, C, D, E, F, G,
H, I, J, K
Automatic transaxle fluid R Every 90,000 km (60,000 miles) A, C, D, E, F, G, H, I
Manual transaxle fluid R Every 120,000 km (80,000 miles) C, D, E, F, G, H, I, J
Drive shaft and boots I Inspect more frequently depending on the
condition C, D, E, F, G, H, I, J
Air cleaner filter R Replace more frequently depending on the
condition C, E
Climate control air filter R Replace more frequently depending on the
condition C, E, G
Brake discs and pads, calipers and rotors I Inspect more frequently depending on the
condition C, D, E, G, H
Brake drums and linings I Inspect more frequently depending on the
condition C, D, E, G, H
Parking brake IInspect more frequently depending on the
condition C, D, G, H
Steering gear rack, linkage and boots I Inspect more frequently depending on the
condition C, D, E, F, G


8-39
8
Maintenance

Vapor hose (for gasoline engine)
and fuel filler cap
The vapor hose and fuel filler cap
should be inspected at those intervals specified in the maintenance schedule.
Make sure that a new vapor hose or
fuel filler cap is correctly replaced.
Vacuum crankcase ventilation
hoses (if equipped)
Inspect the surface of hoses for evi‐
dence of heat and/or mechanical dam‐ age. Hard and brittle rubber, cracking,
tears, cuts, abrasions, and excessive
swelling indicate deterioration. Particu‐ lar attention should be paid to examine
those hose surfaces nearest to high
heat sources, such as the exhaust manifold.
Inspect the hose routing to assure that
the hoses do not come in contact with
any heat source, sharp edges or mov‐ ing component which might cause heat
damage or mechanical wear. Inspect all
hose connections, such as clamps and couplings, to make sure they are se‐
cure, and that no leaks are present. Ho‐
ses should be replaced immediately if there is any evidence of deterioration
or damage.
Air cleaner filter
Have the air cleaner filter replaced by a
professional workshop. Kia recom‐ mends to visit an authorized Kia dealer/
service partner.
Spark plugs (for gasoline engine)
Make sure to install new spark plugs of
the correct heat range.
WARNING
Do not disconnect and inspect sparkplugs when the engine is hot. Youmay burn yourself.
Valve clearance (for Kappa 1.0L
T-GDI engine)
Inspect for excessive valve noise and/or
engine vibration and adjust if necessa‐ ry. In this case, have the system serv‐
iced by a professional workshop. Kia
recommends to visit an authorized Kia dealer/service partner.
Cooling system
Check the cooling system components,
such as the radiator, coolant reservoir, hoses and connections for leakage and
damage. Replace any damaged parts.
Coolant
The coolant should be changed at the
intervals specified in the maintenance
schedule.
Manual transaxle fluid (if
equipped)
Inspect the manual transaxle fluid ac‐
cording to the maintenance schedule.
Automatic transaxle fluid (if
equipped)
Automatic transaxle fluid should not be
checked under normal usage conditions.
Have the automatic transmission fluid changed by a professional workshop
according to the maintenance schedule.
Kia recommends to visit an authorized Kia dealer/service partner.
NOTICE
Automatic transaxle fluid color is ba‐
sically red.
As the vehicle is driven, the auto‐
matic transaxle fluid will begin to
look darker. It is normal condition
and you should not judge the need
(Continued)
Maintenance
8-42

WARNING
nTire age
Tires degrade over time, even whenthey are not being used.Regardless of the remaining tread,we recommend that tires be re‐placed after approximately six (6)years of normal service. Heat causedby hot climates or frequent highloading conditions can accelerate theaging process. Failure to follow thiswarning can result in sudden tirefailure, which could lead to a loss ofcontrol and an accident involving se‐rious injury or death.
4. Tire ply composition and material
The number of layers or plies of rub‐
ber-coated fabric in the tire. Tire man‐ ufacturers also must indicate the ma‐
terials in the tire, which include steel,
nylon, polyester, and others. The letter "R" means radial ply construction; the
letter "D" means diagonal or bias ply
construction; and the letter "B" means belted-bias ply construction.
5. Maximum permissible inflation
pressure
This number is the greatest amount of
air pressure that should be put in the
tire. Do not exceed the maximum per‐ missible inflation pressure. Refer to the
Tire and Loading Information label for
recommended inflation pressure.
6. Maximum load rating
This number indicates the maximum
load in kilograms and pounds that can be carried by the tire. When replacing
the tires on the vehicle, always use a
tire that has the same load rating as the factory installed tire.
7. Uniform tire quality grading
Quality grades can be found where ap‐
plicable on the tire sidewall between tread shoulder and maximum section
width.
For example:TREADWEAR 200TRACTION AA
TEMPERATURE A
Tread wear
The tread wear grade is a comparative
rating based on the wear rate of the tire when tested under controlled con‐
ditions on a specified government test
course. For example, a tire graded 150 would wear one-and-a-half times (1½)
as well on the government course as a
tire graded 100.
The relative performance of tires de‐ pends upon the actual conditions of
their use, however, and may depart sig‐
nificantly from the norm due to varia‐
tions in driving habits, service practices and differences in road characteristics
and climate.
These grades are molded on the side-
walls of passenger vehicle tires. The tires available as standard or optional
equipment on your vehicle may vary
with respect to grade.
Traction - AA, A, B & C
The traction grades, from highest to lowest, are AA, A, B and C. Those
grades represent the tire’s ability to
stop on wet pavement as measured under controlled conditions on specified
government test surfaces of asphalt
and concrete. A tire marked C may have poor traction performance.
Maintenance
8-74

Instrument panel (Driver’s side fuse panel)
SymbolFuse rat‐ingCircuit Protected
20A Tail Gate Unlock Relay, Dead Lock Relay, Door Lock/Unlock Relay
20A Power Outlet
25A Driver Safety Power Window Module
STOP
LAMP15A Stop Signal Electronic Module
15A BCM (Body Control Module), SLM Unit
20A Cigarette Lighter
10A Driver Power Outside Mirror, Passenger Power Outside Mirror, Air Conditioner Control Module, ECM
(Engine Control Module)/PCM (Power train Control Module)
10A Outside Mirror Folding
RH25A Power Window Main Switch, Passenger Power Window Switch(LHD)
20A Front Seat Warmer Control Module
10A DRL (Daytime Running Light) Relay
7.5A With Immobilizer & Smart Key : ECM (Engine Control Module)/PCM (Power train Control Module), En‐ gine Room Junction Block(Start Relay)
Without Immobilizer & Smart Key : Burglar Alarm Relay
7.5A Head Lamp RH, License Lamp RH(Sedan), Rear Combination Lamp (IN) RH(Wagon), ILL (+)
Maintenance

8-84

SymbolFuse rat‐ingCircuit Protected
10ABCM (Body Control Module), Crash Pad Switch, FCA Unit, Lane Departure Warning System, BLIND-
SPOT DETECTION WARNING Radar LH/RH
15AEngine Room Junction Block(Back-Up Lamp Switch), Sport Mode Switch, Speed Sensor, Stop Lamp
Switch, Speed Sensor (In/Out), Transaxle Range Switch
LH25A Power Window Main Switch, Passenger Power Window Switch(RHD)
SPARE25A Spare
10A Rear Fog Lamp Relay
15A Clock Spring
LH7.5A Head Lamp LH, License Lamp LH(Sedan), Rear Combination Lamp (IN) LH(Wagon)
7.5A Front Console Switch, Front Seat Warmer Control Module, Audio, Audio / Video & Navigation Head
Unit, Head Lamp Leveling Device Actuator LH/RH, Air Conditioner Control Module, Electro Chromic
Mirror, Crash Pad Switch, DC-DC Converter, Clock Spring, A/T Shift Lever Indicator
7.5A
Engine Room Junction Block(Multipurpose Check Connector), ABS/ESC (Electronic Stability Control)
Control Module
10A Smart Key Control Module, Stop Lamp Switch
SPARE15A Spare
15A Front Fog Lamp Relay
7.5AEngine Room Junction Block(Air Conditioner Blower Relay), GSL Junction Block(PTC Heater Relay),
DSL Junction Block(Start Relay, Air Conditioner Blower Relay), Air Conditioner Control Module
MODULE510AEngine Room Junction Block(Head Lamp High Relay, Head Lamp Relay), Front Seat Warmer Control
Module, BCM (Body Control Module)


8-85
8
Maintenance