steering wheel KIA TELLURIDE 2022 Features and Functions Guide

ADAS
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
Leading Vehicle Departure Alert†4
Leading Vehicle Departure Alert is designed to inform the driver when the vehicle in front starts moving or departs from a stop . When LVDA is on, your vehicle is stopped, and it detects that the leading vehicle is driving away,
LVDA sounds an alert to let you know you can start driving . If no action is taken after the vehicle in front drives away, then a message will appear on the Instrument Cluster LCD .
LVDA User Settings:
•
To turn LVDA on, press the Mode button A on the Steering Wheel, and go to User Settings in the Instrument Cluster . Press the Move (OK) button B up/down and select Driver Assistance, then press the OK button B to select . Go to Driver Attention Warning and then Leading Vehicle Departure Alert
•Some models access settings through the Vehicle Settings in the audio head unit . Press the Setup hard key on the audio head unit, then press VEHICLE on the screen to enter Vehicle Settings
REMINDERS:
•
When the ignition is cycled, the system returns to its previous state, on or off
•
Always check the front of the vehicle and road conditions before depar ture
The Leading Vehicle Departure Alert system is not a substitute for safe and proper driving . Always drive safely and use caution .
Images are for illustrative purposes only and may not reflect actual feature or operation .
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Leading Vehicle Departure Alert (LVDA) Video
QR Code
Leading vehicle
is driving away
CRUISE
MODE CRUISE
CANCEL
RES
OK SET
CRUISE
CANCEL
RES
OK SET
MODE CRUISE
CANCEL
RES
OK SET
MODE
CANCEL
RES
OK SET
MODECRUISE
CANCEL
RES
OK SET
CRUISE
CANCEL
RES
OK SET
(But ton layout on right of steering wheel)
A
B
See section 5 in the Owner’s Manual for more information .
Your vehicle’s steering wheel buttons may differ from those in the illustrations .
Refer to section 5 in the Owner’s Manual for more information .
A CRUISE ON/OFF button: Press to turn the cruise control ON/OFF
B RES+ button: Press up to resume or increase cruising speed
B SET– button: Press down to set or decrease cruising speed
C CANCEL button: To cancel cruise control setting, do one of the following:
•Press the brake pedal
•Press the CANCEL button
D
Switch Modes*: To switch between standard Cruise Control and Smart Cruise Control, press and hold for more than two seconds
Cruise Control (CC)*
•
Cruise Control is designed to function above approximately 20 mph only
•
Cruise Control will not activate until the brake pedal has been depressed at least once after ignition ON or engine star t
QUICK TIPS
CRUISE
CANCEL
RES
OK SET
A
B
CD
(But ton layout on right of steering wheel)
†LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED18TELLURIDE FEATURES & FUNCTIONS GUIDE

ADAS
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
ALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS . †LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED19
Smart Cruise Control (SCC) is designed to maintain a predetermined distance from vehicles detected ahead by automatically adjusting the driving speed as needed . When traffic is detected, the vehicle will slow down to maintain a set
distance behind traffic without depressing the accelerator or brake pedal .
With SCC on and activated, the vehicle distance set, and the system detects a vehicle slowing or stopping, the system can bring the vehicle to a complete stop . When the vehicle ahead starts to move forward, the SCC system re-engages . If the vehicle ahead stops for more than 3 seconds, the accelerator pedal or the RES+ button must be pressed to start moving the vehicle .
To set/adjust SCC speed:
•Accelerate/decelerate to the desired speed
•Press the Driving Assist CRUISE button A to turn the system ON . The CRUISE indicator will illuminate on the instrument cluster
•Press the R E S + / S E T– button B to set the speed . Press the RES+/S E T– button B up/down to increase/decrease the set speed
To set the vehicle distance:
•Press the Vehicle Distance button C on the steering wheel
•
Each time you press C the vehicle distance will change D, indicated by the number of bars that appear on the display E
To adjust the sensitivity of the SCC system: Press the mode button G on the Steering Wheel . With the OK button H, select Drive Assistance, then SCC Reaction . Then select Fast, Normal or Slow .
To cancel SCC operation: Press the CANCEL button F or press the brake pedal . The LCD screen will display a message that the SCC operation is canceled .
To turn SCC OFF: Press the Driving Assist CRUISE button A . The CRUISE indicator on the instrument cluster will turn OFF .
For illustrative purposes only and may not reflect actual feature or operation . See section 5 in the Owner’s Manual for more information .
(Distances are approximate and var y depending on vehicle speed)
(Display on LCD screen)
Smart Cruise Control (SCC)†4
REMINDERS:
•
CRUISE indicator must be ON in order to operate SCC . The cruise control system will not activate until the brake pedal has been depressed at least once after the ignition is ON or engine star ting
•SCC remains ON when ignition is cycled . The speed set ting will need to be reset when ignition is cycled
•When following a vehicle, the system will automatically adjust your cruise speed based on the vehicle detected in front
•
SCC is also canceled when the driver ’s door is opened, gear shift is changed out of D (Drive), EPB is activated and various other conditions . See the Owner ’s Manual for other conditions
•
If SCC is left on, it can be activated inadver tently . Keep the system off when not in use to avoid set ting a speed which the driver is not aware of
•
SCC is a supplemental system and is not a substitute for safe driving . It is the responsibilit y of the driver to always check the speed and distance to the vehicle ahead
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Smart Cruise Control with Stop & Go Video
QR CODE
•The speed set ting for the SCC can be adjusted under the following conditions:
-You must be traveling at a minimum speed of 20 mph
-When following a vehicle, there is no minimum speed requirement
•When following a vehicle, the system can automatically adjust your cruise speed based on the vehicle detected ahead . If the vehicle detected remains at a standstill for more than 3 seconds, the system will disable
•To change the cruise control mode from SCC to standard cruise control, press and hold but ton C . Repeat to switch back to SCC mode (The SCC system must not be activated to change modes)
QUICK TIPS
CRUISE60MPH
CRUISE
MODE
CRUISE
CANCEL
RES
OK SET
CRUISE
CANCEL
RES
OK SET
MODE CRUISE
CANCEL
RES
OK SET
MODE
CANCEL
RES
OK SET
MODECRUISE
CANCEL
RES
OK SET
CRUISE
CANCEL
RES
OK SET
A
E
G
HB
CF
17 2 f t131f t
82ft
107f tD

ADAS
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
ALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS . †LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED21
Lane Following Assist is designed to help ensure that the vehicle stays centered in its lane A by monitoring the detected lane markings ahead and adjust the steering . When driving, LFA can be switched on and off
by pressing the Driving Assist button B . When turned on, the instrument cluster indicator will initially illuminate white when turned ON . It will remain white when the system does not detect the lane markers . When LFA detects the lane markers and can assist the steering, the LFA icon will illuminate green C .
LFA will operate only when these conditions are met:
•LFA recognizes both sides of the lane markers the vehicle is traveling in
•The vehicle is traveling slower than 120 mph
LFA User Settings:
•
To go to User Settings in the Instrument Cluster, press the Mode button D on the Steering Wheel when the vehicle is at a standstill, gear shift is in Park and with the ignition on or the Engine Start/Stop button* in the ON position, and select User Settings
•
To enable LFA , when in User Settings, press the Move (OK) button E up/down and Select Driver Assistance then Driving Assist, and select Lane Following Assist . Press the OK button E
•
Some models access settings through the Vehicle Settings in the audio head unit . Press the Setup hard key on the audio head unit, then VEHICLE on the screen to enter Vehicle Settings
•
Some vehicles have a Lane Driving Assist / Lane Safety button* on the Driver ’s Panel or the Steering Wheel B . Press to activate Lane Following Assist
Lane Following Assist (LFA)†4
Images are for illustrative purposes only and may not reflect actual feature or operation .
LFA is supplemental . Do not solely rely on this system and always pay attention to the road and its conditions .
See section 5 in the Owner’s Manual for more detailed information, limitations and conditions .
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Lane Following Assist (LFA) Video
QR CODE
A
C
REMINDER: LFA is not a substitute for safe and proper driving . Always drive safely and use caution .
CRUISE
CANCEL
RES
OK SET
(But ton layout on right of steering wheel)
D
E
B

ADAS
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
†LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED22TELLURIDE FEATURES & FUNCTIONS GUIDE
Highway Driving Assist (HDA) is designed to adjust the speed of the vehicle when driving on limited/controlled access highways/freeways . The system can adjust the vehicle’s speed based on available highway speed
information . The automatic speed setting mode is designed to set the speed automatically by adjusting to the current speed limits of the highway the vehicle is traveling on .
To turn HDA on, go to User Settings A in the Instrument Cluster or the Vehicle Settings* in the audio head unit . Go to Driver Assistance > Driving Assist > Highway Driving Assist and press the OK button B on the Steering Wheel .
To activate HDA , turn Smar t Cruise Control (SCC) on by pressing the Driving Assist CRUISE button on the Steering Wheel controls C .
HDA will operate only when these conditions are met:
•The vehicle is traveling slower than 95 mph
•When driving on federal highways
•When the SCC is on and operating
•When the SCC speed is set to current federal highway speed
When HDA is activated and the conditions are met, the Instrument Cluster indicator light D will illuminate green . If the conditions are not met, HDA will be in standby mode and the indicator light D will illuminate white .
When in operation, and if both lanes are recognized, a display E will show the lanes illuminated white and the steering wheel indicator illuminated green .
If HDA is activated, conditions are met and the SCC speed is set by the driver (at the posted highway speed limit or slower), HDA will enter the automatic speed setting mode . The set speed and AUTO will be displayed F in green
and an audible alert will sound .
CRUISE
MODE
CRUISE
CANCEL
RES
OK SET
CRUISE
CANCEL
RES
OK SET
MODE CRUISE
CANCEL
RES
OK SET
MODE
CANCEL
RES
OK SET
MODECRUISE
CANCEL
RES
OK SET
CRUISE
CANCEL
RES
OK SET
CRUISE
CANCEL
RES
OK SET
60mph
mph
REMINDERS:
•
Current highway speeds and controlled or limited access road information may var y . Future navigation updates may change this information
•
If the driver changes the speed while in automatic speed set ting mode, it deactivates and enters a manual mode
•
When the ignition is cycled, the system returns to its previous state, on or off
Highway Driving Assist (HDA)†4
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Highway Driving Assist (HDA) Video
QR CODE
A
C
D
E
F
B
Highway Driving Assist is not a substitute for safe driving, may not detect all objects around the vehicle, and only functions on certain federal highways . Always drive safely and use caution . See the Owner’s Manual for more detailed information, limitations and conditions .
Images are for illustrative purposes only and may not reflect actual feature or operation .
See section 5 in the Owner’s Manual for more information .

ADAS
ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS)
ALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS . †LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED25
CRUISE
MODE
CRUISE
CANCEL
RES
OK SET
CRUISE
CANCEL
RES
OK SET
MODE CRUISE
CANCEL
RES
OK SET
MODE
CANCEL
RES
OK SET
MODECRUISE
CANCEL
RES
OK SET
CRUISE
CANCEL
RES
OK SET
Watch for traffic
Rear Cross-Traffic Collision-Avoidance Assist (RCCA) is designed to warn the driver under certain conditions . It may activate the Electronic Stability Control (ESC) and temporarily apply braking if it detects cross traffic
approaching the vehicle when the vehicle is in reverse .
When the RCCA rear-corner radar sensors detect approaching vehicles from the rear left or rear right side of the vehicle A, RCCA will sound a warning, the warning indicators on the outside rearview mirror will illuminate and a message will appear on the Instrument Cluster LCD B and the audio head unit .* If RCCA detects that the collision risk has increased, RCCA automatically applies the brakes to reduce your speed, potentially helping to minimize the effects of a possible collision .
RCCA is designed to operate under the following conditions:
•When the gear shift is in Reverse
•When the vehicle is moving slower than 6 mph
RCCA User Settings:
•To go to the User Settings menu in the Instrument Cluster, press the Mode button C on the Steering Wheel when the vehicle is at a standstill, gear shift in Park and with the ignition on or the Engine Start/Stop button* in the ON position, and select User Settings
•
To turn RCCA on when in User Settings , press the Move (OK) button D up/down, select Driver Assistance, Parking Safety, Rear Cross-Traffic Safety and then press OK D
•
To set the warning timing, go to User Settings , press the Move (OK) button D up/down, then go to Driver Assistance, Warning Timing and press the OK button D
•Select one of the settings:
–
Early/Normal/Standard: Maximizes the amount of distance between the vehicles before the initial warning occurs
– L a t e : Reduces the amount of distance between the vehicles before the initial warning occurs
•The default Warning Timing is set to Normal . If the Warning Timing is changed, the warning time of other Driver Assistance systems may also change
•
Some models access settings through the Vehicle Settings in the audio head unit . Press the Setup hard key on the audio head unit, then VEHICLE on the screen to enter Vehicle Settings
Rear Cross-Traffic Collision-Avoidance Assist (RCCA)†4
See section 5 in the Owner’s Manual for more information .
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Rear Cross-Traffic Collision-Avoidance Assist (RCCA) Video
QR CODE
A
B
C
D
REMINDERS:
•
The RCCA feature can be activated or deactivated in User Set tings, under Driver Assistance, Parking Safet y
•
When vehicle power is cycled, RCCA will remain in the previous state
•
When a vehicle is approaching within the sensing range, and traveling faster than 3 mph, the RCCA system will show a warning
•
RCCA is a supplemental system . Do not solely rely on this system and always pay at tention to the road and its conditions
•RCCA Warning Volume can be adjusted in the User Set tings in the Instrument Cluster or the Vehicle Set tings on the audio head unit . Go to Driver Assistance, then Warning Volume
QUICK TIP
(But ton layout on right of steering wheel)

†LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED28TELLURIDE FEATURES & FUNCTIONS GUIDE
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Electronic Stability Control Video
QR CODE
REMINDERS:
•
ESC is active by default at vehicle star tup . When ignition is cycled, ESC will turn ON again
•
The ESC indicator light in the instrument cluster will be lit momentarily whenever ESC is active
REMINDERS:
•
HAC does not operate when the gear shift is in P (Park) or N (Neutral) position
•
HAC does not replace the need to apply brakes while the vehicle is stopped on an incline
•
In the event of HAC system malfunction, see an Authorized Kia Dealer for ser vice
•When HAC is active (e .g ., during initial acceleration from a stop on an incline), you may notice that the brakes will momentarily remain engaged after you depress the accelerator
•HAC provides a t wo-second delay before the vehicle may star t rolling backwards
QUICK TIPS
Electronic Stability Control (ESC)†6 /
Traction Control System (TCS)†6
Electronic Stability Control (ESC) is designed to help stabilize the vehicle during certain cornering maneuvers . The Traction Control System (TCS) can help improve traction . It is a good idea to keep both ESC and TCS turned on for daily driving whenever possible .
Press the ESC button B to turn the Traction Control System OFF/ON .
To turn both Electronic Stability Control and the Traction Control System OFF, press and hold the ESC button for more than 3 seconds . Press again to turn ON .
Instrument Cluster Control (Instrument Panel Dimmer)
With the Engine Start/Stop button on or the parking lights/headlights on, press A (+) or (-) to adjust the brightness of the instrument panel illumination .
(But ton located on driver ’s panel, left of the steering wheel)
See section 4 in the Owner’s Manual for more information .
See section 5 in the Owner’s Manual for more information .
See section 5 in the Owner’s Manual for more information .
Hill-Start Assist Control (HAC)†6
Hill-Start Assist Control (HAC) is designed to prevent the vehicle from rolling backwards when accelerating from a stop while on a steep incline .
HAC automatically activates whether ESC is OFF or ON but does NOT activate when ESC has malfunctioned .
AB
DRIVER’S PANEL
DRIVER’S PANEL

ALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS . †LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED29
DRIVER’S PANEL
DRIVER’S PANEL
REMINDER: When the but tons are not pressed, the Reverse Parking Aid Function will not operate and the outside rear view mirrors will not rotate downward .See section 4 in the Owner’s Manual for more information .
For illustrative purposes only . Your actual display, buttons and/or features may vary .
Reverse Parking Aid Function†4
When the gear shift lever is moved into R (Reverse) and the vehicle is moving backwards, the outside rearview mirrors will rotate downward to aid in reverse parking .
To turn Reverse Parking Aid Function ON, move switch A to either the right or to the left . To turn OFF, move switch to the center position .
The outside rearview mirrors will automatically return to their original positions when:
•The Engine Start/Stop button is in the OFF position
•The gear shift lever is moved out of R (Reverse)
•
The outside rearview mirror switch is in the center position
R
L
A
REMINDERS:
•The Engine Star t/Stop but ton needs to be on
•The Gear Shift needs to be in (P) Park
See section 4 in the Owner’s Manual for more information .
For illustrative purposes only . Your actual display, buttons and/or features may vary .(But ton located on driver ’s panel, left of the steering wheel)
Power Liftgate Open/Close Button*
Press and hold the Power Liftgate Open/Close button B to open or close the Liftgate automatically .
B
Manual Folding Mirrors*
To fold the mirrors in manually, pull the mirror towards the window .
Refer to section 4 in the Owner’s Manual for more information .
For illustrative purposes only . Your actual display, buttons and/or features may vary .
If needed, pull the mirror firmly until it folds .
QUICK TIP

AUTO Light – When the light switch is in the AUTO Light position, the tail lights and headlights will turn ON/OFF automatically depending on the amount of light outside the vehicle .
Daytime Running Lights (DRL) – DRL may help others to see the front of your vehicle during the day . The lights will turn on automatically when the ignition or Engine Start/Stop button is ON and the headlight switch is in the AUTO position, unless one of the following occurs:
• Headlights are on
• Parking brake is applied
• Engine is turned off
• Switch is in the DRL OFF position
Headlight / High Beam Lever Operation
•Rotate lever switch to change the headlight function:
•
Press lever away from you to turn high beam headlights ON
•
Pull lever to flash headlights/high beams or to turn off the high beams
High Beam Assist (HBA)* – High Beam Assist is designed to automatically adjust the headlight range by switching between high and low beams based on light detected from other vehicles and road conditions .
To enable HBA , toggle the light switch to the AUTO Light position and turn on the high beams by pushing the lever away from you . The High Beam Assist indicator will illuminate .
*IF EQUIPPED32TELLURIDE FEATURES & FUNCTIONS GUIDE
REMINDERS:
•
High Beam Assist does not operate below cer tain speeds, or in some lighting and driving conditions . Please be aware of your surroundings and exercise proper road etiquet te when operating a vehicle using the high beams
•HBA will operate when vehicle speed exceeds 25 mph
•
If the lever is pushed away from you while HBA is operational, HBA will turn off and the high beams will be on continuously . If the lever is pulled toward you while HBA is operational, HBA will turn off
•If the light switch is switched to the headlight position, HBA will turn off and low beams will be on continuously
•
When the HBA indicator illuminates on the instrument cluster, the HBA is not working properly . See an authorized Kia dealer for ser vice
OFF
OFF
)FBEMJHIU
QPTJUJPO
1BSLJOH
-JHIU
\
QPTJUJPO
AUTOAuto Light /DRL/ High Beam Assist*
OFFOFF position
Headlights & High Beams
See section 4 in the Owner’s Manual for more information .
A
To operate Turn Signals: Move lever up/down for right/left turn signal .
One-touch lane change signal is activated by briefly pressing the turn signal lever slightly for less than 1 second and then releasing . The lane change signal will blink 3 times .
To change how many times the lane change signal blinks (3/5/7), go to User Settings in the LCD instrument cluster modes .
To operate Fog Lights: Press switch A up/down to turn on/off the Fog Lights .
Turn Signals & Fog Lights*
REMINDER: Headlights must be on for fog light operation .
See section 4 in the Owner’s Manual for more information . For illustrative purposes only . Your actual display, buttons and/or features may vary .
STEERING WHEEL CONTROLS
STEERING WHEEL
CONTROLS

See section 4 in the Owner’s Manual for more information .
STEERING WHEEL
CONTROLS
STEERING WHEEL CONTROLS
ALWAYS CHECK THE OWNER ’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS . *IF EQUIPPED33
Headlight position
Parking Light position
AUTOAuto Light /DRL/ High Beam Assist*
OFFOFF position
To operate front wipers & washers:
•Move lever up/down to change wiper modes
MIST: Single wipe LO: Slow wipeOFF: Wiper off HI: Fast wipeINT*/AUTO*: Intermittent*/Auto Rain Sensing*
•Pull to spray and wipe
To operate rear wipers & washers:
•Rotate Rear Wiper switch to change Wiper modes
•Push lever to spray and wipe
Auto Rain Sensing (Auto Control)*
The rain sensor located on the upper end of the windshield glass is designed to sense the amount of rainfall and control the wiping cycle for the proper interval . The more it rains, the faster the wiper operates . When the rain stops, the wiper stops .
To turn ON the auto rain sensing wipers, move lever up/down to AUTO . To adjust the auto rain sensing wiper speed setting, move the speed control switch A up/down .
Auto Rear Wiper* – The feature can be enabled in the User Settings on the Instrument Cluster . When the lever is in the AUTO position, the gear shift is moved into Reverse (R), Auto Rear Wiper activates and will wipe the rear windshield .
Front & Rear Windshield Wipers & Washers
HI
LO
OFF
"
#
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Wipers and Wiper Stalk Video
QR CODE
CImage for illustrative purposes only . See section 7 in the Owner’s Manual for more information .
To lift the windshield wipers to clean the windshield, inspect or replace wiper blades or raise the wipers in snow/ice conditions without damaging the hood, the blades need to be moved to the middle of the windshield (service position) C .
With the ignition ON, turn the ignition OFF, and within 20 seconds move the wiper switch up to the MIST position B and hold the switch for more than two seconds until the wiper blade is in the fully up position .
To return wipers to the normal position, turn the ignition ON, then activate MIST .
Lifting Wipers/Winter Mode (Wiper Service Mode)
Refer to the inside front cover for more information on QR codes .www .youtube .com/KiaFeatureVideos
Wiper Service ModeVideo
QR CODE
MIST: Single wipe
OFF: Wiper off
LO: Slow wipe
HI: Fast wipe
INT*/AUTO: Intermittent*/Auto/Rain Sensing*
•When the Engine Star t/Stop but ton is in the ON position and the wiper switch is in AUTO mode, the wiper will automatically operate once to per form a self-check of the system
•Set the wiper to the OFF position when the wiper is not in use
•Moving lever to HI increases intermit tent wipe frequency and wipe speed . Moving lever to LO decreases frequency of wipes
•Pressing but ton A up increases Intermit tent wipe frequency and wipe speed . Pressing but ton A down decreases frequency of wipes
•On Rear Wipers, intermit tent wipe function is not adjustable
QUICK TIPS

STEERING WHEEL CONTROLS
STEERING WHEEL
CONTROLS
(GT steering wheel illustration shown)
Do not adjust the steering wheel while driving as this may cause you to lose control of the vehicle .
See section 4 in the Owner’s Manual for more information .
A
•It may be helpful to pull/push the bot tom of the Steering Wheel towards/away from you to adjust to the desired distance .
QUICK TIP
To adjust the Steering Wheel, push the lock-release lever A down and adjust to the desired angle B and distance C .
When finished, pull the lock-release lever A up to lock Steering Wheel in place .
Tilt/Telescoping Steering Wheel† 19
C
B
See section 4 in the Owner’s Manual for more information .
REMINDER: If the steering wheel becomes too warm, turn the system off . The heated steering wheel may cause burns even at low temperatures, especially if used for long periods of time .
While the Engine Start/Stop button is in the ON position, press D to turn the steering wheel heater ON . The button indicator will illuminate .
The steering wheel heater will turn off automatically in 30 minutes, or when the button is pressed again to deactivate .
MAP RADIO
N AVMEDIASEEK< SETUP
AUTOOFFREARACSYNC
L
72FAUTO72FH
IPASSENGER
AIRBAGOFF
Heated Steering Wheel*
D
†LEGAL DISCL AIMERS ON BACK INSIDE COVER*IF EQUIPPED34TELLURIDE FEATURES & FUNCTIONS GUIDE