diagram Lancia Musa 2008 Owner handbook (in English)

96
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
SEAT BELTS
USE OF SIDE REAR
AND FRONT SEAT BEALTS
Wear the belt keeping the chest
straight and rested against the back-
rest.
To fasten the seat belts, hold the
tongueA-fig. 1and insert it into the
buckleB, until the locking click is
heard.
If the belt jams when it is extracted,
let it rewind for a short stretch, then
pull it out again without jerking.
Press button Cto release the belt. Ac-
company the belt while it is being re-
wound to prevent twisting.
Through the reel, the belt automati-
cally adapts to the body of the pas-
senger wearing it, thus giving him/her
freedom of movement.The reel may get blocked when the
car is parked on a steep slope: this is
perfectly normal. In addition, the reel
mechanism blocks the belt whenever
it is pulled and in the event of brisk
braking, collisions and on high speed
bends.
The rear seat is supplied with inertial
reel-driven seat belts with three hook-
ing points. Rear seat belts must be worn as
shown in diagram D-fig. 2(5 seat
versions) or diagram E-fig. 3(4 seat
versions).
fig. 1L0D0126m
fig. 2L0D0430m
fig. 3L0D0431m
Never press button C-fig. 1
when travelling.
WARNING
095-112 MUSA 3ed GB 12-11-2007 11:36 Pagina 96

117
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
USING THE
MECHANICAL
GEARBOX
To engage the gears, press the clutch
pedal fully and shift the gear lever
into one of the required positions (the
diagram is shown on the knob).
IMPORTANT Reverse may only be
engaged when the car is at a stand-
still. With the engine running, wait for
at least 2 seconds with the clutch
pedal fully pressed before engaging
reverse to prevent damage to the gears
and grating.
To engage sixth gear (where pro-
vided), operate the lever by pressing
it towards the right in order to avoid
engaging fourth gear by mistake. The
same applies when shifting from sixth
to fifth gear.
To engage reverse Rfrom neutral, lift
the sliding collar A-fig. 2-3 under the
knob while shifting the lever towards
the right and then backwards (only
for petrol versions).
For Multijet versions, only shift the
lever towards the right and then back-
wards.
fig. 2L0D0150m
fig. 3L0D0360m
Do not drive with the hand
resting on the gear lever,
because this pressure, even
if light, over time can wear
gear inner components.
Press the clutch pedal
fully to change gears cor-
rectly. For this reason, there must
be no obstacles on the floor under
the pedals: ensure that rubber mats
(if any) are correctly positioned,
not interfering with the pedals.
WARNING
113-124 MUSA 3ed GB 12-11-2007 11:37 Pagina 117

121
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
STARTING
AND
DRIVING
with load
Existing holes
Existing holes
fig. 4
ASSEMBLY DIAGRAM fig. 4
The tow hook structure must be fastened in the points
shown by the symbol
Øusing a total of 4 M8, 2 M10 and
2 M12 screws.
The hook should be fastened to the body avoiding any
type of drilling and trimming of the rear bumpers that re-
mains visible when the hook is removed.
IMPORTANT It is compulsory to fasten a label (plainly
visible) of suitable size and material with the following
wording:
MAX LOAD ON BALL 60 kg
After fitting, screw holes shall be sealed to
prevent exhaust gas inlet.
WARNING
L0D0256m
> 318 ± 5
Standard trow ball
113-124 MUSA 3ed GB 12-11-2007 11:37 Pagina 121