light Lancia Musa 2009 Owner handbook (in English)

65
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
Operation in position Eis limited to
the time during which the lever is
kept in that position manually..
When released, the stalk will return
to position Aand the wiper will be
automatically stopped.
IMPORTANT Replace wiper blades
as specified in section “Car
maintenance”.RAIN SENSOR
(where provided)
The rain sensor is located behind the
driving mirror in contact with the
windscreen and has the purpose of
automatically adjust the frequency of
the windscreen wiper strokes as to the
rain intensity.
IMPORTANT Keep the window clean
in the sensor area.
Activation
Move the right lever down by one
click.
The activation of the rain sensor is
signalled by a control acquisition
“stroke”.
Turn the knurled ring F-fig. 73to in-
crease the rain sensor sensitivity.
The increase of the sensitivity of the
rain sensor is signalled by a control
and acquisition “stroke”.
By operating the windscreen washer
with the rain sensor enabled, a smart
washing cycle is carried out, without
the additional stroke after 5 seconds;
once completed, the sensor resumes its
regular automatic operation. “Smart washing” function
Pull the stalk towards the steering
wheel (unstable position) to operate
the windscreen washer.
Keeping the stalk pulled for more
than half a second, with just one
movement it is possible to operate the
washer jet and the wiper at the same
time.
When releasing the stalk, the jet stops
immediately, while the wiper carries
out another four strokes.
A further stroke after 6 seconds com-
pletes the wiping operation. Do not use the windscreen
wiper to remove layers of
snow or ice from the wind-
screen. In such conditions,
the windscreen wiper may be sub-
jected to excessive stress and the mo-
tor protection which prevents opera-
tion for a few seconds may trip. If the
issue persists, contact the Lancia
Dealership.
fig. 72L0D0074m
038-094 MUSA 1ed GB 11-07-2008 14:10 Pagina 65

66
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
With windscreen wiper on and reverse
gear engaged, rear window wiping
will be continuous.
Pushing the stalk towards the dash-
board (unstable position) will activate
the rear window washer.
Keeping the stalk pushed for over half
a second will activate also the rear
window wiper.
Releasing the stalk will activate the
smart washing function as described
for the windscreen wiper. The sensor reactivation is signalled by
a windscreen wiper “stroke”.
The rain sensor is able to recognize
and automatically adjust itself in the
presence of the following particular
conditions:
❒impurities on the controlled sur-
face (salt, dirt, etc.);
❒difference between day and night.
Deactivation
Change the stalk knurled ring posi-
tion from Bor turn the ignition key to
STOP.
At the next start-up (key at MAR), the
sensor will not be reactivated even if
the stalk is at B. To activate the sen-
sor, move the stalk to position AorC
and then to position Bor turn the sen-
sitivity adjustment knurled ring.
fig. 73L0C0073m
Streaks of water may cause
unnecessary blade moving.
WARNING
REAR WINDOW WASHER/
WIPER fig. 74
The device can work only when the
ignition key is on MAR.
Turning the knurled ring Afrom po-
sition
åto position 'will operate the
rear window wiper as follows:
❒intermittent operation if the
windscreen wiper is off;
❒synchronised with the windscreen
wiper (but with half stroke fre-
quency);
fig. 74L0D0075m
038-094 MUSA 1ed GB 11-07-2008 14:10 Pagina 66

67
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
CRUISE CONTROL
(constant speed
regulator)
(where provided)
It is a device able to support the dri-
ver, with electronic control, which al-
lows driving at speed over 30 km/h
on long and straight dry roads (e.g.:
motorways), at a desired speed, with-
out pressing the accelerator pedal.
Therefore it is not suggested to use
this device on extra-urban roads with
traffic. Do not use it in town.TO MEMORISE SPEED
Proceed as follows:
❒turn knurling ring A-fig. 75toON
and press the accelerator pedal to
the required speed;
❒push the lever up (+) for at least
three seconds, then release it: the
car speed will be stored. The ac-
celerator pedal may be released.
If needed (e.g. for overtaking), press
the accelerator pedal to accelerate: the
car will return to the previously set
speed when the pedal is released. DEVICE ENGAGEMENT
Turn the knurling ring A-fig. 75to
ON.
The device must be enabled only with
4
thor 5thgear engaged. Travelling
downhill with the device engaged, the
car speed may increase more than the
memorised one. When the device is
activated the instrument panel warn-
ing light Üturns on and the relevant
message (where provided) is dis-
played on the multifunctional display.
fig. 75L0D0076m
038-094 MUSA 1ed GB 11-07-2008 14:10 Pagina 67

68
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
DEVICE DISENGAGEMENT
Turn the knurled ring A-fig. 75to
OFFor the ignition key to STOP. In
addition, the device is automatically
disengaged in one of the following
cases:
❒pressing the brake pedal. TO REDUCE MEMORISED SPEED
The stored speed can be increased in
two ways:
❒disengaging the device and then
memorising the new speed;
or
❒moving the stalk downwards (
–)
until reaching the new speed which
will be memorised automatically.
Each operation of the stalk will cor-
respond to a slight reduction in speed
(about 1 km/h), while keeping the
stalk downwards will correspond to a
continuous speed reduction. RESTORING STORED SPEED
If the device has been disengaged for
example pressing the brake or clutch
pedal, the memorised speed can be re-
set as follows:
❒accelerate gradually until reaching
a speed approaching the one
memorised;
❒engage the gear selected at the
time of speed memorising (4
thor
5thgear);
❒press the button RES B.
TO INCREASE THE MEMORISED
SPEED
The stored speed can be increased
in two ways:
❒pressing the accelerator and then
memorising the new speed
reached;
or
❒moving the stalk upwards (
+).
Each operation of the stalk will cor-
respond to a slight increase in speed
(about 1 km/h), while keeping the
stalk upwards will correspond to a
continuous speed increase.
While travelling with the
device engaged, do not set
the gearshift lever to neutral.
WARNING
In case of malfunctioning or
fault of the device, turn the
knurled ring to OFF and contact the
Lancia Dealership, after checking
that the protection fuse is not blown.
WARNING
038-094 MUSA 1ed GB 11-07-2008 14:10 Pagina 68

69
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
LIGHTS
FRONT LIGHT fig. 76
SwitchA-turn on/off these lights.
With switch Ain central position,
lightsCandDwill turn on/off when
opening/closing the front doors.
With switch Apressed on the left side,
lightsCandDwill always stay off.
With switch Apressed on the right
side, lights CandCwill always stay
on.
Light turning on/off is gradual.
SwitchBperforms the spot function;
with light off, it will turn on:
❒lightCif pressed on the left side;
❒lightDif pressed on the right side.Light timing when getting into the
car
Lights will turn on as follows:
❒for about 10 seconds when un-
locking the doors;
❒for about 3 minutes when opening
one of the doors;
❒for about 10 seconds when closing
the doors (within 3 minutes).
Timing will stop when turning the ig-
nition key to MAR.
Light timing when getting out of the
car
After removing the key from the igni-
tion switch, the lights will turn on as
follows:
❒within 2 minutes from turning the
engine off for about 10 seconds;
❒when opening one of the doors for
about 3 minutes;
❒when closing the doors for about
10 seconds (within 3 minutes).
Timing will stop automatically when
locking the doors. IMPORTANT Before getting out of
the car, make sure the switch is at
central position: lights off with doors
closed in order to avoid draining the
battery.
In any case, if the switch is left inad-
vertently to the On position, the lights
will turn off automatically 15 minutes
after turning the engine off.
Ceiling light timing
To facilitate getting in/out of the car
at night or with poor lighting, 2 dif-
ferent timed switching on modes have
been provided:
fig. 76L0D0077m
038-094 MUSA 1ed GB 11-07-2008 14:10 Pagina 69

70
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
Light timing when getting out of the
car
After removing the key from the igni-
tion switch, the lights will turn on as
follows:
❒within 2 minutes from turning the
engine off for about 10 seconds;
❒when opening one of the doors for
about 3 minutes;
❒when closing the doors for about
10 seconds (within 3 minutes).
Timing will stop automatically when
locking the doors. Light timing (where provided)
To facilitate getting in/out of the car
at night or with poor lighting, 2 dif-
ferent timed switching on modes have
been provided:
Light timing when getting into the
car
Lights will turn on as follows:
❒for about 10 seconds when un-
locking the doors;
❒for about 3 minutes when opening
one of the doors;
❒for about 10 seconds when closing
the doors (within 3 minutes).
Timing will stop when turning the ig-
nition key to MAR. REAR LIGHT
The light will turn on/off by pressing
the movable lens rightwards or left-
wards as shown in fig. 77.
If the box is longitudinal to the roof
panel, the light is integrated into the
box itself.
If the car is equipped with a sunroof,
two 5W lights are fitted in the rear
roof panel fig. 78.
fig. 77L0D0078mfig. 78L0D0254m
038-094 MUSA 1ed GB 11-07-2008 14:10 Pagina 70

71
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
LIGHT CONTROL
BUTTONS
HAZARD LIGHTS fig. 79-80
They turn on by pressing switch A,
regardless of the position of the igni-
tion key.
When the function is active, the
switch flashes and warning lightsÎ
and¥on the panel blink.
Press the switch again to turn the
lights off.
FRONT FOG LIGHTS
(where provided) fig. 81
To turn front fog lights on, press but-
ton
5, to activate these lights it is
necessary to have the side/taillights
switched on.
To turn them off, press again the
switch or turn the side/taillights off.
fig. 79L0D0080m
fig. 80L0D0081m
fig. 81L0D0385m
The use of hazard lights is
governed by the Highway
Code of the country you are in. Keep
to the rules.
WARNINGREAR FOG LIGHTS fig. 82
They turn on, with low beams or front
fog lights on, pressing the button
4.
To turn them off, press again the
switch or turn the low beams or front
fog lights off.
fig. 82L0D0386m
038-094 MUSA 1ed GB 11-07-2008 14:10 Pagina 71

72
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
INERTIAL FUEL
CUT-OFF SWITCH
It is located in the bottom, near the
passenger side pillar; to access it, re-
move the carpet. It trips in the event
of a collision cutting the fuel supply
off; as a consequence, the engine turns
off.
When the switch trips, the instrument
panel warning light
èturns on and
the relevant message (where pro-
vided) is displayed on the reconfig-
urable multifunctional display.
Carefully inspect the car to ensure
that there are no fuel leaks, e.g. from
the engine compartment, under the
car or near the tank.
If, after a crash, you smell
fuel or see leaks from the
fuel system, do not reset the switch
to avoid fine risk.
WARNING
fig. 84L0D0388m
If no fuel leaks are detected and the
car can start, press button A-fig. 84
in order to reactivate the fuel feeding
system and turn the lights on.
After a crash, turn the ingition key to
STOPto avoid draining the battery.
038-094 MUSA 1ed GB 11-07-2008 14:10 Pagina 72

73
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
INTERNAL
EQUIPMENT
UPPER ODDMENT DRAWERS fig.
85-86
To open the drawers, unlock the de-
sired cover by means of the device A
and lift it to the stable opening posi-
tion.
CompartmentC-fig. 89and com-
partment DIN D-fig. 89are located in
the dashboard, in central position.
Compartment DIN Dcan be removed
in order to install the sound system
from the Lineaccessori Lancia range.
fig. 85L0D0389m
fig. 86L0D0087m
Do not travel with the odd-
ment drawers open: they
could hurt the passengers in case of
crash.
WARNING
fig. 87L0D0088m
fig. 88L0D0418m
fig. 89L0D0090m
ODDMENT COMPARTMENTS
The oddment compartment A-fig. 87
is located in the dashboard, opposite
to the front passenger.
An extractable oddment bag E-fig.
89, belonging to the Lineaccessori
Lancia range, can be placed inside the
compartmentA.
CompartmentB-fig. 88is located in
the dashboard, on the left of the steer-
ing wheel.
038-094 MUSA 1ed GB 11-07-2008 14:10 Pagina 73

74
SAFETY
DEVICES
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICALSPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
ODDMENT SHELF
ON ROOF PANEL fig. 94
The shelf is used to rapidly store light
objects (e.g. documents, maps etc.)
IMPORTANT Do not store heavy ob-
jects on the shelf nor hang on to it.
The shelf is alternative to the sunroof.
GLASS RECESS –
CAN RECESS fig. 92
The glass/can recesses are located on
the central console in front of the
handbrake.
CARD RECESS fig. 93
The central console features recesses
to keep telephone cards, magnetic
cards or motorway tickets. DOOR POCKETS fig. 91
Paper/map pockets are located in
door panels.
fig. 90L0D0343m
fig. 91L0D0153m
fig. 92L0D0091m
fig. 93L0D0092m
fig. 94L0D0093m
038-094 MUSA 1ed GB 11-07-2008 14:10 Pagina 74