key battery Lancia Musa 2010 Owner handbook (in English)

13
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
KEY KIT AND
DOOR LOCKING
SYSTEM
CODE CARD Fig. 10
(for versions/markets, where
provided)
The car is delivered the keys and a
CODE card which bears the following
information:
❒the mechanical key code Bto be
given to the Lancia Dealership
when ordering duplicate keys.
IMPORTANT In order to ensure per-
fect efficiency of the electronic devices
contained inside the keys, they should
never be exposed to direct sunlight.
MAIN KEY WITH REMOTE
CONTROL fig. 11
The metal insert of the key Aretracts
into the grip.
The key operates:
❒the ignition switch;
❒the door lock on drive side;
❒operation of the emergency front
and rear door lock release system
D-fig. 12from the outside for use
the electric system is not working
(e.g. flat battery);
fig. 10L0D0376m
All the keys and the CODE
card must be handed over
to the new owner when sell-
ing the car.
fig. 11b (for versions/markets,
where provided)L0D0491m
❒operation of the child lock E-fig.
12on rear doors.
Press button B-fig. 11to open the
metallic part A.
fig. 12L0D0246mfig. 11aL0D0377m

16
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
Request for additional remote
controls
The system may recognise up to 8 re-
mote controls. Should a new remote
control be necessary, contact a Lancia
Dealership, taking with you the
CODE card, a personal identity doc-
ument and the car’s ownership docu-
ments.MECHANICAL KEY
(SPARE) fig, 15
The metal insert of the key E-fig. 15
is fixed.
The key operates:
❒the ignition switch;
❒the door lock on drive side;
❒operation of the door safety device
in case of electric system failure
(e.g. flat battery);
❒operation of the child lock on rear
doors. Replacing the remote control
battery Fig. 14
To replace the battery, proceed as fol-
lows:
❒press button Aand open the metal
insertB;
❒turn the screw Cto using a fine bit
screwdriver;
❒take out the battery case Dand re-
place the battery Erespecting its
polarity;
❒refit the battery case Dinside the
key and lock it by turning the
screw C.
fig. 14b (for versions/markets, where
provided)L0D0492m
Used batteries are harmful
to the environment. They
should be disposed of as
specified by law in the spe-
cial containers provided, or take
them to the Lancia Dealership,
which will deal with their disposal.
fig. 14aL0D0379m

36
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
New mission
The new mission begins after:
– “manual” resetting by the user, by
pressing the relevant button;
– “automatic” resetting, when the
“Trip distance” reaches 9999.9 km or
when the “Travel time” reaches 99.59
(99 hours and 59 minutes);
– after disconnecting/reconnecting the
battery.
IMPORTANT “General Trip” resets
will reset “Trip B” at the same time,
while resetting “Trip B” will only re-
set the values of the trip B function. Average speed
This shows the car average speed as a
function of the overall time elapsed
since the start of the new mission.
Journey time
This value shows the time elapsed
since the start of the new mission.
IMPORTANT If information is not
available, the message “----” will ap-
pear instead of the Trip Computer
values. Displaying of the values will
be resumed when normal operation is
restored without resetting the values
displayed before the problem nor
starting a new mission.
TRIP button fig. 29
ButtonTRIPlocated on the top of the
right steering column stalk is used
(with ignition key at MAR) to display
and reset the previously described val-
ues to start a new mission:
– short push to display the different
values
– long push to reset and then start a
new mission. Values displayed
Range
This indicates the indicative distance
which may be travelled with the fuel in
the tank assuming that driving condi-
tions do not change. The display will
show the reading “----“ when the fol-
lowing events take place:
– range lower than 50 km (or 30
miles) or fuel level less than 4 litres in
the tank;
– car left parked with engine running
for a long time.
Distance travelled
This value shows the distance covered
from the start of the new mission.
Average consumption
This indicates the indicative average
consumption from the start of the new
mission.
Instantaneous fuel consumption
This indicates the fuel consumption.
The value is constantly updated. The
message “----” will appear on the dis-
play if the car is parked with the en-
gine running.
fig. 29L0D0026m

69
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
CEILING LIGHTS
FRONT CEILING LIGHT
fig. 74
SwitchA-turns these lights on/off .
With switch Ain central position,
lightsCandDwill turn on/off when
opening/closing the front doors.
With switch Apressed on the left side,
lightsCandDwill always stay off.
With switch A-pressed on the right
side, lights CandDwill always stay
on.
The lights will be turned on/off grad-
ually.
SwitchBis used for operating the
spot light function; it works as follows
(light off):
❒lightCif the left side is pressed;
❒lightDif pressed on the right side.Lights when getting into the car
Lights will be turned on as follows:
❒for about 10 seconds when the door
is unlocked;
❒for about 3 minutes when a door is
opened;
❒for about 10 seconds when the
doors are closed (within the three
minutes).
Timing will stop when turning the ig-
nition key to MAR.
Light when getting out of the car
After removing the key from the igni-
tion switch, the lights will turn on as
follows:
❒within 2 minutes from turning the
engine off for about 10 seconds;
❒when a door is opened for about 3
minutes;
❒for about 10 seconds when the
doors are closed (within the three
minutes).
Timing will stop automatically when
locking the doors. IMPORTANT Before getting out of
the vehicle, make sure the switch is at
central position: lights off with doors
closed in order to avoid draining the
battery.
In any case, if the switch is left inad-
vertently to the on position, the lights
will turn off automatically 15 minutes
after turning the engine off.
Courtesy light timing
On certain versions to facilitate get-
ting in/out of the car at night or with
poor lighting, 2 different timed
switching on modes have been pro-
vided.
fig. 74L0D0077m

72
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
FUEL CUT OFF
SWITCH
The switch is located on the bottom of
the car, near the pillar on passenger
side. Move the carpet aside to reach
the switch. It is tipped by a crash and
cuts off the fuel feed, thus stopping
the engine.
When the device is activated the
warning light
èturns on together
with the relevant message on the re-
configurable multifunctional display
(for versions/markets, where pro-
vided).
Inspect the car carefully for fuel leak-
ages (e.g. in the engine compart-
ment), under the car or near the fuel
tank.
If, after a crash, you smell
fuel or see leaks from the
fuel system, do not reset the switch
to avoid fine risk.
WARNING
fig. 81L0D0388m
Press button A-fig. 81to reactivate
the fuel feed system if no leakage is
found and the car is worthy of re-
suming travel.
After the accident, remember to turn
the ignition key to STOPto prevent
draining the battery.

114
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
SAFETY
STARTING
AND DRIVING
STARTING THE
ENGINE
The car is provided with an electronic
engine lock device: refer to “The Lan-
cia CODE system” paragraph in
“Dashboard and controls” if you can-
not start the engine. The engine may
be noisier during the first seconds of
operation, particularly after a long pe-
riod of inactivity. This is characteris-
tic of hydraulic tappets, the timing
system chosen for petrol engine ver-
sions to reduce the number of servic-
ing interventions and does effects nei-
ther functionality nor reliability.
STARTING PROCEDURE FOR
PETROL VERSIONS
Proceed as follows:
❒apply the handbrake;
❒put the gear lever into neutral;
❒press the clutch pedal all the way
down without touching the accel-
erator;
❒turn the ignition key to AV Vand
let it go the moment the engine
starts.If the engine does not start at the first
attempt, return the ignition key to
STOPbefore repeating the attempt to
start the engine. If with the key at
MARthe instrument panel warning
lightYstays on with warning lightU, turn the key back to STOPand
then back to MAR; if the warning
light stays on, try with the other keys
provided.
It is dangerous to run the
engine in closed environ-
ments. The engine consumes oxy-
gen and engine exhaust contains
carbon dioxide, carbon oxide and
other toxic gasses.
WARNING
It is advisable not to de-
mand maximum perfor-
mance from your car (e.g.
excessive accelerations,
long distances at top rpm, excessive
intense braking, etc.) as soon as the
engine is started.
Do not leave the key in the
ignition switch in the MAR
position with the engine off
to avoid unnecessary con-
sumption of electricity which could
drain the battery.
Contact a Lancia Dealership if you
still cannot start the engine.
IMPORTANT Never leave the ignition
key to MARwhen the engine is off.
PROCEDURE FOR
MULTIJET VERSIONS
Proceed as follows:
❒apply the handbrake;
❒put the gear lever into neutral;
❒turn the ignition key to MAR;
warning lights m,
UandY;

116
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
SAFETY
STARTING
AND DRIVING
PARKING THE
VEHICLE
Proceed as follows:
❒Stop the engine and engage the
handbrake;
❒Engage a gear (on a slope, engage
first gear if the vehicle is faced up-
hill or reverse if it is faced down-
hill) and leave the wheels steered.
If the car is parked on a steep slope,
it is further advisable to block the
wheels with a wedge or stone. Avoid
parking for a long time with one
wheel on the pavement or steered
against the curb. Do not leave the key
in the ignition switch at MARto pre-
vent draining the battery. Always re-
move the key when you leave the car.
HANDBRAKE
The handbrake lever is located be-
tween the two front seats.
Pull the lever upwards to operate the
handbrake.
Four or five notches are normally suf-
ficient to lock the car on flat terrain,
while nine or ten may be necessary on
a steep slope with the car loaded. IMPORTANT If this is not the case,
contact Lancia Dealership to have the
handbrake adjusted.
When the handbrake lever is pulled
up and the ignition key is at MAR, the
instrument panel warning light
xwill turn on.
Proceed as follows to release the
handbrake:
❒slightly lift the handbrake and
press release button A-fig. 1;
❒hold the button Apressed and
lower the lever; the warning light
xon the instrument panel will go
out.
Press the brake pedal when carrying
out this operation to prevent the car
from moving accidentally.
IMPORTANT if the handbrake lever
tends to reach end of stroke (groove
on the central tunnel), go to a Lancia
dealership to have the handbrake ad-
justed correctly.
fig. 1L0D0149m
Never leave children unat-
tended in the car. Always
remove the ignition key
when leaving the car and
take it out with you.

127
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND
MESSAGES
If when turning the key to
MAR the warning light ¬does not turn on or if it stays on
when travelling (together with the
message on the multifunctional
display, where provided) there
could be a failure in safety sys-
tems; in this event air bags or pre-
tensioners may not be deployed in
case of impact or, in a minor num-
ber of cases, they be deployed ac-
cidentally. Contact Lancia Dealer-
ship immediately to have the sys-
tem checked.
Failure of warning light
¬is indicated by warning
light“which will blink for longer
than the normal 4 seconds indicat-
ing that the front passenger airbag
is off. The airbag system will au-
tomatically deactivate the passen-
ger airbag (front and side, for ver-
sions/markets, where provided). In
this case, warning light
¬may not
indicate fault to the system. Con-
tact Lancia Dealership immedi-
ately to have the system checked.
WARNING
WARNING
HOT ENGINE COOLANT
(red)
When the ignition key is
moved to MAR, the warning
light turns on and should go off after
a few seconds.
The warning light turns on when the
engine is overheated.
If the warning light comes on, proceed
as follows:
❒during normal travel: stop the
car, stop the engine and check that
the water level in the vessel is not
under the MINline. In this case,
wait for a few minutes for the en-
gine to cool down when slowly and
carefully open the cap, top-up with
coolant and check that the level is
between the MINandMAXrefer-
ences on the vessel itself. Also check
for leakages. Go to a Lancia Deal-
ership if the warning should come
on when the engine is started again.
u
❒In the case of demanding use
(e.g. towing trailers uphill or car at
full load): slow down and stop the
car if the warning light stays on.
Stand for 2 or 3 minutes with the
engine running and slightly acceler-
ated to promote a better circulation
of coolant. Then stop the engine.
Check correct liquid level as de-
scribed above.
IMPORTANT After taxing operation,
it is advisable to keep the engine on
and slightly accelerated for a few min-
utes before switching it off.
The display will show the dedicated
message.
LOW BATTERY
CHARGE (red)
When the ignition key is
moved to MAR, the warning
light turns on and should go out as
soon as the engine is started (with the
engine running at idle speed a brief
delay in going out is allowed). Go to
a Lancia Dealership immediately if
the warning light stays on.
w

136
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
OPENING/CLOSING
THE DOORS
Emergency device for opening
the doors from the outside
The doors are provided with a device
for locking all the door using the lock
in case of a power fault.
Proceed as follows to lock the doors:
❒insert the ignition key in lock B-
fig. 1
❒turn the device to position 1and
close the door.
fig. 1L0D0247m
STARTING THE
ENGINE
JUMP STARTING
If the battery is flat, the engine may
be started using an auxiliary battery
with the same capacity or a little
higher than the flat one.
Proceed as follows to start the engine:
❒connect the positive terminals (+
sign near terminal) of both batter-
ies using a lead; To reopen the doors:
❒insert the key in the lock on dri-
ver’s side and turn it anticlockwise
❒open the driver’s door
❒operate the door levers from the
inside of the vehicle for the re-
maining doors.

157
WARNING
LIGHTS AND
MESSAGES
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICA-
TIONS
INDEX
DASHBOARD
AND
CONTROLS
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
Remove the key from the
ignition switch and switch
off all loads before replacing a
fuse.
WARNING
FUSE LOCATION
The fuses are contained in two dash-
boards, one on the dashboard on the
left hand of the steering column and
one in the engine compartment next
to the battery.
Dashboard fusebox fig. 37
To access the dashboard fusebox, loosen
the fastening screws A-fig. 36and then
remove the protection panel B.
L0D0200m
fig. 36L0D0424m
fig. 37