warning Lancia Thema 2012 Owner handbook (in English)

WARNING!
Fast spinning tires can be danger-
ous. Forces generated by excessive
wheel speeds may cause tire damage
or failure. A tire could explode and
injure someone. Do not spin your
vehicle's wheels faster than 48 km/h
or for more than 30 seconds con-
tinuously when you are stuck, and
do not let anyone near a spinning
wheel, no matter what the speed.
TREAD WEAR
INDICATORS
Tread wear indicators are in the origi-
nal equipment tires to help you in
determining when your tires should
be replaced. These indicators are molded into the
bottom of the tread grooves. They will
appear as bands when the tread depth
becomes 2 mm. When the tread is
worn to the tread wear indicators, the
tire should be replaced.
LIFE OF TIRE
The service life of a tire is dependent
upon varying factors including, but
not limited to:
 Driving style
 Tire pressure
 Distance driven
WARNING!
Tires and the spare tire should be
replaced after six years, regardless of
the remaining tread. Failure to fol-
low this warning can result in sud-
den tire failure. You could lose con-
trol and have a collision resulting in
serious injury or death.
Keep dismounted tires in a cool, dry
place with as little exposure to light as
possible. Protect tires from contact
with oil, grease, and gasoline. REPLACEMENT TIRES
The tires on your new vehicle provide
a balance of many characteristics.
They should be inspected regularly
for wear and correct cold tire inflation
pressure. The manufacturer strongly
recommends that you use tires
equivalent to the originals in size,
quality and performance when re-
placement is needed. (Refer to the
paragraph on “Tread Wear Indica-
tors”). Refer to the “Tire and Loading
Information” placard for the size des-
ignation of your tire. The Load Index
and Speed Symbol for your tire will be
found on the original equipment tire
sidewall. See the Tire Sizing Chart
example found in the Tire Safety In-
formation section of this manual for
more information relating to the Load
Index and Speed Symbol of a tire.
It is recommended to replace the two
front tires or two rear tires as a pair.
Replacing just one tire can seriously
affect your vehicle’s handling. If you
ever replace a wheel, make sure that
the wheel’s specifications match those
of the original wheels.
1 — Worn Tire
2 — New Tire
217

It is recommended you contact your
original equipment or an authorized
tire dealer with any questions you
may have on tire specifications or ca-
pability. Failure to use equivalent re-
placement tires may adversely affect
the safety, handling, and ride of your
vehicle.WARNING!
 Do not use a tire, wheel size orrating other than that specified
for your vehicle. Some combina-
tions of unapproved tires and
wheels may change suspension di-
mensions and performance char-
acteristics, resulting in changes to
steering, handling, and braking of
your vehicle. This can cause un-
predictable handling and stress to
steering and suspension compo-
nents. You could lose control and
have a collision resulting in seri-
ous injury or death. Use only the
tire and wheel sizes with load rat-
ings approved for your vehicle.
(Continued)
WARNING!(Continued)
 Never use a tire with a smaller
load index or capacity, other than
what was originally equipped on
your vehicle. Using a tire with a
smaller load index could result in
tire overloading and failure. You
could lose control and have a col-
lision.
 Failure to equip your vehicle with
tires having adequate speed capa-
bility can result in sudden tire fail-
ure and loss of vehicle control.CAUTION!
Replacing original tires with tires of
a different size may result in false
speedometer and odometer read-
ings.
TIRE CHAINS
Use of Security Chain Company
(SCC) Super Z6 SZ143 or Iceman Z6
IZ-643 cables or equivalent are rec-
ommended on 225/65R17 tires.
NOTE:
Do not use tire chains on a com-
pact spare tire.
CAUTION!
To avoid damage to your vehicle or
tires, observe the following precau-
tions:
 Use chains on 225/65R17 tires only.
 Because of restricted chain clear-
ance between tires and other sus-
pension components, it is impor-
tant that only chains in good
condition are used. Broken chains
can cause serious damage. Stop
the vehicle immediately if noise
occurs that could indicate chain
breakage. Remove the damaged
parts of the chain before further
use.
 Install chains on the rear wheels
as tightly as possible and then re-
tighten after driving about
0.8 km.
 Do not exceed 48 km/h.
 Drive cautiously and avoid severe
turns and large bumps, especially
with a loaded vehicle.
 Use on rear wheels only.
 Do not drive for prolonged period
on dry pavement.
(Continued)
218

CAUTION!(Continued)
 Observe the tire chain manufac-
tur er's instructions on the method
of installation, operating speed,
and conditions for use. Always use
the lower suggested operating
speed of the chain manufacturer if
different from the speed r ecom-
mended by the manufacture.
NOTE:
In order to avoid damage to tires,
chains, and your vehicle do not
drive for a prolonged period on dry
pavement. Observe the tire chain
manufacturer's instructions on
method of installation, operating
speed, and conditions for usage.
Always use the lower suggested oper-
ating speed if both the chain manu-
facturer and vehicle manufacturer
suggest a maximum speed. This no-
tice applies to all chain traction de-
vices, including link and cable (ra-
dial) chains. TIRE ROTATION
RECOMMENDATIONS
Tires on the front and rear axles of
vehicles operate at different loads and
perform different steering, driving,
and braking functions. For these rea-
sons, they wear at unequal rates.
These effects can be reduced by timely
rotation of tires. The benefits of rota-
tion are especially worthwhile with ag-
gressive tread designs such as those on
all season type tires. Rotation will in-
crease tread life, help to maintain mud,
snow and wet traction levels, and con-
tribute to a smooth, quiet ride.Refer to the “Maintenance Schedule”
for the proper maintenance intervals.
The reasons for any rapid or unusual
wear should be corrected prior to ro-
tation being performed.
TIRE PRESSURE
MONITOR SYSTEM
(TPMS)
The Tire Pressure Monitor System
(TPMS) will warn the driver of a low
tire pressure based on the vehicle rec-
ommended cold placard pressure.The tire pressure will vary with tem-
perature by about 0.069 BAR for ev-
ery 6.5°C. This means that when the
outside temperature decreases, the
tire pressure will decrease. Tire pres-
sure should always be set based on
cold inflation tire pressure. This is
defined as the tire pressure after the
vehicle has not been driven for at least
three hours, or driven less than
1.6 km after a three hour period. The
cold tire inflation pressure must not
exceed the maximum inflation pres-
sure molded into the tire sidewall. Re-
fer to “Tires – General Information”
in “Starting and Operating” for infor-
mation on how to properly inflate the
vehicle’s tires. The tire pressure will
also increase as the vehicle is driven -
this is normal and there should be no
adjustment for this increased pres-
sure.
The TPMS will warn the driver of a
low tire pressure if the tire pressure
falls below the low-pressure warning
limit for any reason, including low
temperature effects and natural pres-
sure loss through the tire.
219

The TPMS will continue to warn the
driver of low tire pressure as long as
the condition exists, and will not turn
off until the tire pressure is at or above
the recommended cold placard pres-
sure. Once the low tire pressure warn-
ing (Tire Pressure Monitoring [TPM]
Telltale Light) illuminates, you must
increase the tire pressure to the rec-
ommended cold placard pressure in
order for the TPM Telltale Light to
turn off. The system will automati-
cally update and the TPM Telltale
Light will turn off once the system
receives the updated tire pressures.
The vehicle may need to be driven for
up to 20 minutes above 24 km/h in
order for the TPMS to receive this
information.
For example, your vehicle may have a
recommended cold (parked for more
than three hours) placard pressure of
2.07 BAR. If the ambient temperature
is 20°C and the measured tire pres-
sure is 1.86 BAR, a temperature drop
to ­7°C will decrease the tire pressure
to approximately 1.58 BAR. This tire
pressure is sufficiently low enough to
turn ON the TPM Telltale Light. Driv-ing the vehicle may cause the tire
pressure to rise to approximately 1.86
BAR, but the TPM Telltale Light will
still be ON. In this situation, the TPM
Telltale Light will turn OFF only after
the tires are inflated to the vehicle’s
recommended cold placard pressure
value.
CAUTION!
 The TPMS has been optimized for
the original equipment tires and
wheels. TPMS pressures and
warning have been established for
the tire size equipped on your ve-
hicle. Undesirable system opera-
tion or sensor damage may result
when using replacement equip-
ment that is not of the same size,
type, and/or style. Aftermarket
wheels can cause sensor damage.
Do not use aftermarket tire seal-
ants or balance beads if your ve-
hicle is equipped with a TPMS, as
damage to the sensors may result.
(Continued)
CAUTION!(Continued)
 After inspecting or adjusting the
tire pressure, always reinstall the
valve stem cap. This will prevent
moisture and dirt from entering
the valve stem, which could dam-
age the TPM sensor.
NOTE:
 The TPMS is not intended to re- place normal tire care and
maintenance or to provide
warning of a tire failure or con-
dition.
 The TPMS should not be used as a tire pressure gauge while ad-
justing your tire pressure.
 Driving on a significantly under- inflated tire causes the tire to
overheat and can lead to tire
failure. Under-inflation also re-
duces fuel efficiency and tire
tread life, and may affect the ve-
hicle’s handling and stopping
ability.
 The TPMS is not a substitute for proper tire maintenance, and it
is the driver’s responsibility to
maintain correct tire pressure
220

using an accurate tire pressure
gauge, even if under-inflation
has not reached the level to trig-
ger illumination of the TPM
Telltale Light.
 Seasonal temperature changes will affect tire pressure, and the
TPMS will monitor the actual
tire pressure in the tire.
PREMIUM SYSTEM
The Tire Pressure Monitor System
(TPMS) uses wireless technology with
wheel rim mounted electronic sensors
to monitor tire pressure levels. Sen-
sors mounted to each wheel as part of
the valve stem transmit tire pressure
readings to the receiver module.
NOTE:
It is particularly important for you
to check the tire pressure in all of
the tires on your vehicle monthly
and to maintain the proper pres-
sure.
The TPMS consists of the following
components:
 Receiver module,
 Four TPM sensors,  Various TPMS messages, which
display in the Electronic Vehicle In-
formation Center (EVIC), and
 TPM Telltale Light
Tire Pressure Monitoring Low
Pressure Warnings The TPM Telltale Light will il-
luminate in the instrument
cluster and a chime will sound
when tire pressure is low in one or
more of the four active road tires. In
addition, the EVIC will display a
"LOW TIRE" message and a graphic
showing the pressure values of each
tire with the low tire pressure values
flashing.
Should this occur, you should stop as
soon as possible and inflate the tires
with a low pressure condition (those
flashing in the EVIC graphic) to the
vehicle’s recommended cold placard
pressure inflation value. Once the sys-
tem receives the updated tire pres-
sures, the system will automatically
update, the graphic display in the
EVIC will stop flashing, and the TPM
Telltale Light will turn off. The ve-
hicle may need to be driven for up to 20 minutes above 24 km/h in order
for the TPMS to receive this informa-
tion.
Service TPMS Warning
If a system fault is detected, the TPM
Telltale Light will flash on and off for
75 seconds and then remain on solid.
The system fault will also sound a
chime. In addition, the EVIC will dis-
play a "SERVICE TPM SYSTEM"
message for a minimum of five sec-
onds and then display dashes (- -) in
place of the pressure value to indicate
which sensor is not being received.
If the ignition switch is cycled, this
sequence will repeat, providing the
system fault still exists. If the system
fault no longer exists, the TPM Tell-
tale Light will no longer flash, and the
"SERVICE TPM SYSTEM" message
will no longer display, and a pressure
value will display in place of the
dashes. A system fault can occur due
to any of the following:
1. Signal interference due to elec-
tronic devices or driving next to facili-
ties emitting the same radio frequen-
cies as the TPM sensors.
221

2. Installing aftermarket window
tinting that contains materials that
may block radio wave signals.
3. Accumulation of snow or ice
around the wheels or wheel housings.
4. Using tire chains on the vehicle.
5. Using wheels/tires not equipped
with TPM sensors.
The EVIC will also display a "SER-
VICE TPM SYSTEM" message for a
minimum of five seconds when a sys-
tem fault related to an incorrect sen-
sor location fault is detected. In this
case, the "SERVICE TPM SYSTEM"
message is then followed with a
graphic display with pressure values
still shown. This indicates that the
pressure values are still being received
from the TPM sensors but they may
not be located in the correct vehicle
position. The system still needs to be
serviced as long as the "SERVICE
TPM SYSTEM" message is displayed.Vehicles With Compact Spare
1. The compact spare tire does not
have a TPM sensor. Therefore, the
TPMS will not monitor the pressure in
the compact spare tire.
2. If you install the compact spare
tire in place of a road tire that has a
pressure below the low-pressure
warning limit, upon the next ignition
switch cycle, the TPM Telltale Light
will remain ON and a chime will
sound. In addition, the graphic in the
EVIC will still display a flashing pres-
sure value.
3. After driving the vehicle for up to
20 minutes above 24 km/h, the TPM
Telltale Light will flash on and off for
75 seconds and then remain on solid.
In addition, the EVIC will display a
"SERVICE TPM SYSTEM" message
for a minimum of five seconds and
then display dashes (- -) in place of
the pressure value.
4. For each subsequent ignition
switch cycle, a chime will sound, the
TPM Telltale Light will flash on and
off for 75 seconds and then remain on
solid, and the EVIC will display a"SERVICE TPM SYSTEM" message
for a minimum of five seconds and
then display dashes (- -) in place of
the pressure value.
5. Once you repair or replace the
original road tire and reinstall it on
the vehicle in place of the compact
spare, the TPMS will update auto-
matically. In addition, the TPM Tell-
tale Light will turn OFF and the
graphic in the EVIC will display a new
pressure value instead of dashes (- -),
as long as no tire pressure is below the
low-pressure warning limit in any of
the four active road tires. The vehicle
may need to be driven for up to
20 minutes above 24 km/h in order
for the TPMS to receive this informa-
tion.
TPMS DEACTIVATION
The TPMS can be deactivated if re-
placing all four wheel and tire assem-
blies (road tires) with wheel and tire
assemblies that do not have TPMS
Sensors, such as when installing win-
ter wheel and tire assemblies on your
vehicle To deactivate the TPMS, first,
replace all four wheel and tire assem-
blies (road tires) with tires not
222

Many of these materials intended for
gum and varnish removal may con-
tain active solvents or similar ingredi-
ents. These can harm fuel system gas-
ket and diaphragm materials.WARNING!
Carbon monoxide (CO) in exhaust
gases is deadly. Follow the precau-
tions below to prevent carbon mon-
oxide poisoning:
 Do not inhale exhaust gases. Theycontain carbon monoxide, a color-
less and odorless gas which can
kill. Never run the engine in a
closed area, such as a garage, and
never sit in a parked vehicle with
the engine running for an ex-
tended period. If the vehicle is
stopped in an open area with the
engine running for more than a
short period, adjust the ventila-
tion system to force fresh, outside
air into the vehicle.
(Continued)
WARNING!(Continued)
 Guard against carbon monoxide
with proper maintenance. Have
the exhaust system inspected ev-
ery time the vehicle is raised.
Have any abnormal conditions re-
paired promptly. Until repaired,
drive with all side windows fully
open.
 Keep the trunk closed when driv-
ing your vehicle to prevent carbon
monoxide and other poisonous ex-
haust gases from entering the ve-
hicle.
FUEL REQUIREMENTS
— DIESEL ENGINES
This vehicle must only use pre-
mium diesel fuel that meets the
requirements of EN 590. Biodiesel
blends that meet EN 590 may also
be used.
CAUTION!
The manufacturer requires that you
must fuel this vehicle with Ultra
Low Sulfur Highway Diesel fuel
(15 ppm Sulfur maximum) and pro-
hibits the use of Low Sulfur High-
way Diesel fuel (500 ppm Sulfur
maximum) to avoid damage to the
emissions control system.WARNING!
Do not use alcohol or gasoline as a
fuel blending agent. They can be
unstable under certain conditions
and hazardous or explosive when
mixed with diesel fuel.Diesel fuel is seldom completely free of
water. To prevent fuel system trouble,
drain the accumulated water from the
fuel/water separator using the fuel/
water separator drain provided. If you
buy good quality fuel and follow the
cold weather advice above, fuel condi-
tioners should not be required in your
vehicle. If available in your area, a high
cetane “premium” diesel fuel may offer
improved cold-starting and warm-up
performance.
225

ADDING FUEL
1. Press the fuel filler door release
switch (located in thedriver's door
map pocket).
2. Open the fuel filler door.
3. There is no fuel filler cap. A flap-
per door inside the pipe seals the sys-
tem. 4. Insert the fuel nozzle fully into the
filler pipe – the nozzle opens and
holds the flapper door while refueling.
NOTE:
Only the correct size nozzle opens
the latches allowing the flapper
door to open.
5. Fill the vehicle with fuel – when
the fuel nozzle “clicks” or shuts off the
fuel tank is full.
6. Remove the fuel nozzle and close
the fuel door.
NOTE:
A funnel is provided (located in the
trunk in the spare tire area) to
open the flapper door to allow for
emergency refueling with a gas
can.
CAUTION!
To avoid fuel spillage and overfill-
ing, do not “top off” the fuel tank
after filling.WARNING!
 Never have any smoking materi-
als lit in or near the vehicle when
the fuel door is open or the tank is
being filled.
 Never add fuel when the engine is
running. This is in violation of
most state and federal fire regula-
tions and may cause the “Mal-
function Indicator Light” to turn
on.
 A fire may result if gasoline is
pumped into a portable container
that is inside of a vehicle. You
could be burned. Always place gas
containers on the ground while
filling.
EMERGENCY FUEL
FILLER DOOR RELEASE
If you are unable to open the fuel filler
door, use the fuel filler door emer-
gency release.
1. Open the trunk.
Fuel Filler Door Release Switch
Fuel Filler Door
Fuel Funnel
226

2. Remove the access cover (located
on the left side inner trim panel).
3. Pull the release cable.
VEHICLE LOADING
The load carrying capacity of your
vehicle is shown on the “Vehicle Cer-
tification Label.” This information
should be used for passenger and lug-
gage loading as indicated.Do not exceed the specified Gross Ve-
hicle Weight Rating (GVWR) or the
Gross Axle Weight Rating (GAWR).
VEHICLE CERTIFICATION
LABEL
Your vehicle has a Vehicle Certifica-
tion Label affixed to the rear of the
driver's door.
The label contains the following infor
-
mation:
 Name of manufacturer
 Month and year of manufacture
 Gross Vehicle Weight Rating
(GVWR)
 Gross Axle Weight Rating (GAWR) front
 Gross Axle Weight Rating (GAWR) rear
 Vehicle Identification Number (VIN)
 Type of Vehicle
 Month Day and Hour of Manufac- ture (MDH)
The bar code allows a computer scan-
ner to read the VIN. GROSS VEHICLE WEIGHT
RATING (GVWR)
The GVWR is the total allowable
weight of your vehicle. This includes
driver, passengers, and cargo. The to-
tal load must be limited so that you do
not exceed the GVWR.
GROSS AXLE WEIGHT
RATING (GAWR)
The GAWR is the maximum capacity
of the front and rear axles. Distribute
the load over the front and rear axles
evenly. Make sure that you do not
exceed either front or rear GAWR.
WARNING!
Because the front wheels steer the
vehicle, it is important that you do
not exceed the maximum front or
rear GAWR. A dangerous driving
condition can result if either rating is
exceeded. You could lose control of
the vehicle and have a collision.
OVERLOADING
The load carrying components (axle,
springs, tires, wheels, etc.) of your
vehicle will provide satisfactory ser-
Access CoverRelease Cable
227

Gross Combination Weight Rating
(GCWR)
The GCWR is the total permissible
weight of your vehicle and trailer
when weighed in combination.
NOTE:
The GCWR rating includes a 68 kg
allowance for the presence of a
driver.
Gross Axle Weight Rating (GAWR)
The GAWR is the maximum capacity
of the front and rear axles. Distribute
the load over the front and rear axles
evenly. Make sure that you do not
exceed either front or rear GAWR.
Refer to “Vehicle Loading/Vehicle
Certification Label” in “Starting and
Operating” for further information.WARNING!
It is important that you do not ex-
ceed the maximum front or rear
GAWR. A dangerous driving condi-
tion can result if either rating is ex-
ceeded. You could lose control of the
vehicle and have a collision.Tongue Weight (TW)
The tongue weight is the downward
force exerted on the hitch ball by the
trailer. In most cases, it should not be
more than 5% of the trailer load. You
must consider this as part of the load
on your vehicle.
Frontal Area
The frontal area is the maximum
height multiplied by the maximum
width of the front of a trailer.
Trailer Sway Control
The trailer sway control is a telescop-
ing link that can be installed between
the hitch receiver and the trailer
tongue that typically provides adjust-
able friction associated with the tele-
scoping motion to dampen any un-
wanted trailer swaying motions while
traveling.
Weight-Carrying Hitch
A weight-carrying hitch supports the
trailer tongue weight, just as if it were
luggage located at a hitch ball or some
other connecting point of the vehicle.
These kinds of hitches are the most
popular on the market today and they are commonly used to tow small- and
medium-sized trailers.
Weight-Distributing Hitch
A weight-distributing system works
by applying leverage through spring
(load) bars. They are typically used
for heavier loads to distribute trailer
tongue weight to the tow
vehicle's
front axle and the trailer axle(s).
When used in accordance with the
manufacturer's directions, it provides
for a more level ride, offering more
consistent steering and brake control
thereby enhancing towing safety. The
addition of a friction / hydraulic sway
control also dampens sway caused by
traffic and crosswinds and contrib-
utes positively to tow vehicle and
trailer stability. Trailer sway control
and a weight distributing (load equal-
izing) hitch are recommended for
heavier Tongue Weights (TW) and
may be required depending on vehicle
and trailer configuration / loading to
comply with Gross Axle Weight Rat-
ing (GAWR) requirements.
229