ESP Lancia Thema 2012 Owner handbook (in English)

CAUTION!(Continued)
 Observe the tire chain manufac-
tur er's instructions on the method
of installation, operating speed,
and conditions for use. Always use
the lower suggested operating
speed of the chain manufacturer if
different from the speed r ecom-
mended by the manufacture.
NOTE:
In order to avoid damage to tires,
chains, and your vehicle do not
drive for a prolonged period on dry
pavement. Observe the tire chain
manufacturer's instructions on
method of installation, operating
speed, and conditions for usage.
Always use the lower suggested oper-
ating speed if both the chain manu-
facturer and vehicle manufacturer
suggest a maximum speed. This no-
tice applies to all chain traction de-
vices, including link and cable (ra-
dial) chains. TIRE ROTATION
RECOMMENDATIONS
Tires on the front and rear axles of
vehicles operate at different loads and
perform different steering, driving,
and braking functions. For these rea-
sons, they wear at unequal rates.
These effects can be reduced by timely
rotation of tires. The benefits of rota-
tion are especially worthwhile with ag-
gressive tread designs such as those on
all season type tires. Rotation will in-
crease tread life, help to maintain mud,
snow and wet traction levels, and con-
tribute to a smooth, quiet ride.Refer to the “Maintenance Schedule”
for the proper maintenance intervals.
The reasons for any rapid or unusual
wear should be corrected prior to ro-
tation being performed.
TIRE PRESSURE
MONITOR SYSTEM
(TPMS)
The Tire Pressure Monitor System
(TPMS) will warn the driver of a low
tire pressure based on the vehicle rec-
ommended cold placard pressure.The tire pressure will vary with tem-
perature by about 0.069 BAR for ev-
ery 6.5°C. This means that when the
outside temperature decreases, the
tire pressure will decrease. Tire pres-
sure should always be set based on
cold inflation tire pressure. This is
defined as the tire pressure after the
vehicle has not been driven for at least
three hours, or driven less than
1.6 km after a three hour period. The
cold tire inflation pressure must not
exceed the maximum inflation pres-
sure molded into the tire sidewall. Re-
fer to “Tires – General Information”
in “Starting and Operating” for infor-
mation on how to properly inflate the
vehicle’s tires. The tire pressure will
also increase as the vehicle is driven -
this is normal and there should be no
adjustment for this increased pres-
sure.
The TPMS will warn the driver of a
low tire pressure if the tire pressure
falls below the low-pressure warning
limit for any reason, including low
temperature effects and natural pres-
sure loss through the tire.
219

The TPMS will continue to warn the
driver of low tire pressure as long as
the condition exists, and will not turn
off until the tire pressure is at or above
the recommended cold placard pres-
sure. Once the low tire pressure warn-
ing (Tire Pressure Monitoring [TPM]
Telltale Light) illuminates, you must
increase the tire pressure to the rec-
ommended cold placard pressure in
order for the TPM Telltale Light to
turn off. The system will automati-
cally update and the TPM Telltale
Light will turn off once the system
receives the updated tire pressures.
The vehicle may need to be driven for
up to 20 minutes above 24 km/h in
order for the TPMS to receive this
information.
For example, your vehicle may have a
recommended cold (parked for more
than three hours) placard pressure of
2.07 BAR. If the ambient temperature
is 20°C and the measured tire pres-
sure is 1.86 BAR, a temperature drop
to ­7°C will decrease the tire pressure
to approximately 1.58 BAR. This tire
pressure is sufficiently low enough to
turn ON the TPM Telltale Light. Driv-ing the vehicle may cause the tire
pressure to rise to approximately 1.86
BAR, but the TPM Telltale Light will
still be ON. In this situation, the TPM
Telltale Light will turn OFF only after
the tires are inflated to the vehicle’s
recommended cold placard pressure
value.
CAUTION!
 The TPMS has been optimized for
the original equipment tires and
wheels. TPMS pressures and
warning have been established for
the tire size equipped on your ve-
hicle. Undesirable system opera-
tion or sensor damage may result
when using replacement equip-
ment that is not of the same size,
type, and/or style. Aftermarket
wheels can cause sensor damage.
Do not use aftermarket tire seal-
ants or balance beads if your ve-
hicle is equipped with a TPMS, as
damage to the sensors may result.
(Continued)
CAUTION!(Continued)
 After inspecting or adjusting the
tire pressure, always reinstall the
valve stem cap. This will prevent
moisture and dirt from entering
the valve stem, which could dam-
age the TPM sensor.
NOTE:
 The TPMS is not intended to re- place normal tire care and
maintenance or to provide
warning of a tire failure or con-
dition.
 The TPMS should not be used as a tire pressure gauge while ad-
justing your tire pressure.
 Driving on a significantly under- inflated tire causes the tire to
overheat and can lead to tire
failure. Under-inflation also re-
duces fuel efficiency and tire
tread life, and may affect the ve-
hicle’s handling and stopping
ability.
 The TPMS is not a substitute for proper tire maintenance, and it
is the driver’s responsibility to
maintain correct tire pressure
220

Methanol along with other alcohols
called cosolvents. Problems that re-
sult from using Methanol/gasoline or
E-85 Ethanol blends are not the re-
sponsibility of the manufacturer.
While MTBE is an oxygenate made
from Methanol, it does not have the
negative effects of Methanol.CAUTION!
Do not use gasolines containing
Methanol or E-85 Ethanol. Use of
these blends may result in starting
and driveability problems and may
damage critical fuel system compo-
nents.
Ethanol
The manufacturer recommends that
your vehicle be operated on fuel con-
taining no more than 10% Ethanol.
Purchasing your fuel from a reputable
supplier may reduce the risk of ex-
ceeding this 10% limit and/or of re-
ceiving fuel with abnormal properties.
It should also be noted that an in-
crease in fuel consumption should be
expected when using Ethanol-
blended fuels, due to the lower energy
content of Ethanol. Problems that result from using
Methanol/gasoline or E-85 Ethanol
blends are not the responsibility of the
manufacturer. While MTBE is an oxy-
genate made from Methanol, it does
not have the negative effects of
Methanol.
CAUTION!
Use of fuel with Ethanol content
higher than 10% may result in en-
gine malfunction, starting and oper-
ating difficulties and materials deg-
radation. These adverse effects
could result in permanent damage to
your vehicle.
Clean Air Gasoline
Many gasolines are now being
blended that contribute to cleaner air,
especially in those areas where air
pollution levels are high. These new
blends provide a cleaner burning fuel
and some are referred to as “reformu-
lated gasoline.”
The manufacturer supports these ef-
forts toward cleaner air. You can help
by using these blends as they become
available. MMT In Gasoline
MMT is a manganese containing me-
tallic additive that is blended into
some gasoline to increase octane.
Gasoline blended with MMT provides
no performance advantage beyond
gasoline of the same octane number
without MMT. Gasoline blended with
MMT reduces spark plug life and re-
duces emission system performance in
some vehicles. The manufacturer rec-
ommends that gasoline without MMT
be used in your vehicle. The MMT
content of gasoline may not be indi-
cated on the gasoline pump; therefore,
you should ask your gasoline retailer
whether or not his/her gasoline con-
tains MMT.
Materials Added To Fuel
Besides using unleaded gasoline with
the proper octane rating, gasolines
that contain detergents, corrosion and
stability additives are recommended.
Using gasolines that have these addi-
tives will help improve fuel economy,
reduce emissions, and maintain ve-
hicle performance.
Indiscriminate use of fuel system
cleaning agents should be avoided.
224

WARNING!(Continued)
 Take care not to allow the con-
tents of TIREFIT to come in con-
tact with hair, eyes, or clothing.
TIREFIT is harmful if inhaled,
swallowed, or absorbed through
the skin. It causes skin, eye, and
respiratory irritation. Flush im-
mediately with plenty of water if
there is any contact with eyes or
skin. Change clothing as soon as
possible, if there is any contact
with clothing.
 TIREFIT Sealant solution con-
tains latex. In case of an allergic
reaction or rash, consult a physi-
cian immediately. Keep TIREFIT
out of reach of children. If swal-
lowed, rinse mouth immediately
with plenty of water and drink
plenty of water. Do not induce
vomiting! Consult a physician im-
mediately. SEALING A TIRE WITH
TIREFIT
(A) Whenever You Stop To Use
TIREFIT:
1. Pull over to a safe location and
turn on the vehicle’s Hazard Warning
flashers.
2. Verify that the valve stem (on the
wheel with the deflated tire) is in a
position that is near to the ground.
This will allow the TIREFIT Hoses
(6) and (7) to reach the valve stem
and keep the TIREFIT kit flat on the
ground. This will provide the best po-
sitioning of the kit when injecting the
sealant into the deflated tire and run-
ning the air pump. Move the vehicle as
necessary to place the valve stem in
this position before proceeding.
3. Place the transmission in PARK
(auto transmission) or in Gear
(manual transmission) and turn Off
the ignition.
4. Set the parking brake.
(B) Setting Up To Use TIREFIT:
1. Turn the Mode Select Knob (5) to
the Sealant Mode position. 2. Uncoil the Sealant Hose (6) and
then remove the cap from the fitting
at the end of the hose.
3. Place the TIREFIT kit flat on the
ground next to the deflated tire.
4. Remove the cap from the valve
stem and then screw the fitting at the
end of the Sealant Hose (6) onto the
valve stem.
5. Uncoil the Power Plug (8) and in-
sert the plug into the vehicle’s 12 Volt
power outlet.
NOTE:
Do not remove foreign objects (e.g.,
screws or nails) from the tire.
(C) Injecting TIREFIT Sealant
Into The Deflated Tire:
 Always start the engine before
turning ON the TIREFIT kit.
NOTE:
Manual transmission vehicles
must have the parking brake en-
gaged and the shift lever in NEU-
TRAL.
 After pressing the Power Button (4), the sealant (white fluid) will
243

5. Start the engine in the vehicle that
has the booster battery, let the engine
idle a few minutes, and then start the
engine in the vehicle with the dis-
charged battery.
Once the engine is started, remove the
jumper cables in the reverse sequence:
6. Disconnect the negative(-)jumper
cable from the remote negative (-)
post of the vehicle with the discharged
battery.
7. Disconnect the negative end (-)of
the jumper cable from the negative (-)
post of the booster battery.
8. Disconnect the opposite end of the
positive (+)jumper cable from the
positive (+)post of the booster bat-
tery.
9. Disconnect the positive (+)end of
the jumper cable from the remote
positive (+)post of the discharged ve-
hicle.
If frequent jump-starting is required
to start your vehicle you should have
the battery and charging system in-
spected at your authorized dealer.
CAUTION!
Accessories that can be plugged into
the vehicle power outlets draw
power from the vehicle’s battery,
even when not in use (i.e., cellular
phones, etc.). Eventually, if plugged
in long enough, the vehicle’s battery
will discharge sufficiently to degrade
battery life and/or prevent the en-
gine from starting.
FREEING A STUCK
VEHICLE
If your vehicle becomes stuck in mud,
sand, or snow, it can often be moved
by a rocking motion. Turn your steer-
ing wheel right and left to clear the
area around the front wheels. Then
shift back and forth between DRIVE
and REVERSE. Using minimal accel-
erator pedal pressure to maintain the
rocking motion, without spinning the
wheels, is most effective.
CAUTION!
Racing the engine or spinning the
wheels may lead to transmission
overheating and failure. Allow the
engine to idle with the shift lever in
NEUTRAL for at least one minute
after every five rocking-motion
cycles. This will minimize overheat-
ing and reduce the risk of transmis-
sion failure during prolonged efforts
to free a stuck vehicle.
NOTE:
Turn off the Electronic Stability
Program (ESP) (for versions/
markets, where provided), or
Traction Control System (TCS) (for
versions/markets, where pro-
vided) before rocking the vehicle.
Refer to “Electronic Brake Con-
trol” in “Starting And Operating”
for further information.
248

 Use a high quality cleaner wax toremove road film, stains and to pro-
tect your paint finish. Take care
never to scratch the paint.
 Avoid using abrasive compounds and power buffing that may dimin-
ish the gloss or thin out the paint
finish.CAUTION!
Do not use abrasive or strong clean-
ing materials such as steel wool or
scouring powder that will scratch
metal and painted surfaces.
Special Care
 If you drive on salted or dusty roads or if you drive near the ocean, hose
off the undercarriage at least once a
month.
 It is important that the drain holes in the lower edges of the doors,
rocker panels, and trunk be kept
clear and open.
 If you detect any stone chips or scratches in the paint, touch them
up immediately. The cost of such
repairs is considered the responsi-
bility of the owner.  If your vehicle is damaged due to an
accident or similar cause, which de-
stroys the paint and protective
coating, have your vehicle repaired
as soon as possible. The cost of such
repairs is considered the responsi-
bility of the owner.
 If you carry special cargo such as chemicals, fertilizers, de-icer salt,
etc., be sure that such materials are
well packaged and sealed.
 If a lot of driving is done on gravel roads, consider mud or stone
shields behind each wheel.
 Use Touch Up Paint or equivalent on scratches as soon as possible.
Your authorized dealer has touch
up paint to match the color of your
vehicle.
Wheel And Wheel Trim Care
All wheels and wheel trim, especially
aluminum and chrome-plated wheels
should be cleaned regularly with a
mild soap and water to prevent corro-
sion. To remove heavy soil and/or ex-
cessive brake dust, use a nonabrasive,
non-acidic cleaner. Do not use scour-
ing pads, steel wool, a bristle brush, or metal polishes. Do not use oven
cleaner. Avoid automatic car washes
that use acidic solutions or harsh
brushes that may damage the wheels’
protective finish.
Stain Repel Fabric Cleaning
Procedure (for versions/markets,
where provided)
Stain Repel seats may be cleaned in
the following manner:
 Remove as much of the stain as
possible by blotting with a clean,
dry towel.
 Blot any remaining stain with a clean, damp towel.
 For tough stains, apply a mild soap solution to a clean, damp cloth and
remove the stain. Use a fresh, damp
towel to remove soap residue.
 Do not use any harsh solvents or any other form of protectants on
Stain Repel products.
Interior Care
Interior trim should be cleaned start-
ing with a damp cloth. Do not use
harsh cleaners.
272

Your leather upholstery can be best
preserved by regular cleaning with a
damp soft cloth. Small particles of
dirt can act as an abrasive and dam-
age the leather upholstery and should
be removed promptly with a damp
cloth. Stubborn soils can be removed
easily with a soft cloth and appropri-
ate products. Care should be taken to
avoid soaking your leather upholstery
with any liquid. Please do not use
polishes, oils, cleaning fluids, sol-
vents, detergents, or ammonia-based
cleaners to clean your leather uphol-
stery. Application of a leather condi-
tioner is not required to maintain the
original condition.WARNING!
Do not use volatile solvents for
cleaning purposes. Many are poten-
tially flammable, and if used in
closed areas they may cause respira-
tory harm.Cleaning Headlights
Your vehicle has plastic headlights
that are lighter and less susceptible to
stone breakage than glass headlights.
Plastic is not as scratch resistant as
glass and therefore different lens
cleaning procedures must be fol-
lowed.
To minimize the possibility of scratch-
ing the lenses and reducing light out-
put, avoid wiping with a dry cloth. To
remove road dirt, wash with a mild
soap solution followed by rinsing.
Do not use abrasive cleaning compo-
nents, solvents, steel wool or other
aggressive material to clean the
lenses.
Glass Surfaces
All glass surfaces should be cleaned
on a regular basis with any commer-
cial household-type glass cleaner.
Never use an abrasive type cleaner.
Use caution when cleaning the inside
rear window equipped with electric
defrosters or the right rear quarter
window equipped with the radio an- tenna. Do not use scrapers or other
sharp instrument that may scratch
the elements.
When cleaning the rear view mirror,
spray cleaner on the towel or rag that
you are using. Do not spray cleaner
directly on the mirror.
Cleaning Plastic Instrument
Cluster Lenses
The lenses in front of the instruments
in this vehicle are molded in clear
plastic. When cleaning the lenses,
care must be taken to avoid scratch-
ing the plastic.
1. Clean with a wet soft rag or micro-
fiber towel. A mild soap solution may
be used, but do not use high alcohol
content or abrasive cleaners. If soap is
used, wipe clean with a clean damp
rag.
2. Dry with a soft cloth.
273

Cavity Cartridge Fuse Mini-Fuse Description
36— 10 Amp Red Anti-Lock Brake Module (ABS/ESP Module)
37 — 10 Amp Red Engine Controller (PCM)/Rad Fan Relay Coils
38 — 10 Amp Red Airbag Module/Start Feed
39 — 10 Amp Red Power Steering Module/AC Clutch Relay/Cabin Heater Re-
lay Coils — Diesel Only
48 — 10 Amp Red DTCM/Diesel Scr Module — Diesel Only
49 — 15 Amp Blue ASD Feed #3
50 — 15 Amp Blue ASD Feed #4
51 — 20 Amp Yellow Vacuum Pump
52 — —Spare
53 — —Spare
Rear Power Distribution
Center
There is also a power distribution cen-
ter located in the trunk under the
spare tire access panel. This center
contains fuses and relays.
Opening The Access Panel
Rear Power Distribution Center
276

ARRANGEMENTS FOR DEALING
WITH THE VEHICLE AT THE
END OF ITS LIFE
LANCIA has been committed for
many years to safeguarding the envi-
ronment through the constant im-
provement of its production processes
and manufacturing products that are
increasingly “eco-compatible”.
To give customers the best possible
service in terms of respecting environ-
mental laws and in response to Euro-
pean Directive 2000/53/EC govern-
ing vehicles at the end of their life,
LANCIA is offering its customers the
opportunity of handing over their ve-
hicle* at the end of its life without
incurring any additional costs.
The European Directive sets out that
when the vehicle is handed over the
last keeper or owner should not incur
any expenses as a result of it having a
zero or negative market value.
In all European Union countries, until
1st January 2007, only vehicles regis-
tered after 1st July 2002 were col-
lected free of charge, while since 2007
collection has been free of charge irre-spective of the year of registration as
long as the vehicle contains its basic
components (in particular, the engine
and bodywork) and has no additional
waste.
To hand your vehicle over at the end
of its life without extra cost, go to one
of our Dealerships or LANCIA-
authorized collection and scrapping
centres.
These centres have been carefully
chosen to offer high quality service for
the collection, treatment and recy-
cling of unused vehicles with respect
to the environment.
You can find further information on
these collection and scrapping centres
either from a LANCIA or LANCIA
Commercial Vehicle Dealership or by
calling the freephone number 00800
526242 00 or by going on the
LANCIA website.
(*) Vehicle for transporting passen-
gers with a maximum of nine seats
and a total permitted weight of 3.5 t
286

Through Flowing, Rising, or
Shallow Standing Water . . . 204
Driving to Achieve Maximum
Fuel Economy . . . . . . . . . . . . 165
Electric Rear Window
Defrost . . . . . . . . . . . . . . . . . 145
Electric Remote Mirrors . . . . . . 64
Electrical Power Outlets . . . . . 140
Electronic Brake Control
System . . . . . . . . . . . . . . . . . 209
Anti-Lock Brake System . . . 209
Brake Assist System . . . . . . 209
Traction Control System . . . 209
Electronic Power Distribution
Center (Fuses) . . . . . . . . . . . . 274
Electronic Speed Control
(Cruise Control) . . . . . . . 115,117
Electronic Stability Control
(ESC) . . . . . . . . . . . . . . . . . . 210
Electronic Vehicle Information
Center (EVIC) . . . . . . . . 134,159
Emergency Deck Lid Release . . 25
Emergency Trunk Release . . . . 25
Emergency, In Case of Freeing Vehicle When
Stuck . . . . . . . . . . . . . . . . 248
Hazard Warning Flasher . . . 240
Jump Starting . . . . . . . . . . 246 Overheating . . . . . . . . . . . . 240
Towing . . . . . . . . . . . . . . . 251
Engine Air Cleaner . . . . . . . . . . . . 259
Break-In Recommendations . . 50
Compartment . . . . . . . 255,256
Compartment
Identification . . . . . . . . 255,256
Coolant (Antifreeze) . . . 265,284
Cooling . . . . . . . . . . . . . . . 265
Exhaust Gas Caution . . . . . . 51
Fails to Start . . . . . . . . . . . 192
Flooded, Starting . . . . . . . . 192
Fuel Requirements . . . . . . . 223
Jump Starting . . . . . . . . . . 246
Oil . . . . . . . . . . . . 258,283,284
Oil Change Interval . . . 164,258
Oil Disposal . . . . . . . . . . . . 259
Oil Filter . . . . . . . . . . . . . . 259
Oil Selection . . . . . 258,259,283
Oil Synthetic . . . . . . . . . . . 259
Overheating . . . . . . . . . . . . 240
Starting . . . . . . . . . . . . . . . 191
Temperature Gauge . . . . . . 159
Enhanced Accident Response
Feature . . . . . . . . . . . . . . . . . . 39
Entry System, Illuminated . . . . 16
Ethanol . . . . . . . . . . . . . . . . 224
Event Data Recorder . . . . . . . . 41 Exhaust Gas Caution . . . . . 51,264
Exhaust System . . . . . . . . 51,264
Exterior Folding Mirrors . . . . . . 63
Exterior Lighting . . . . . . . . . . 104
Exterior Lights . . . . . . . . . . . . 53
Filler Location Fuel . . . . . . . . 156
Filters
Air Cleaner . . . . . . . . . . . . 259
Air Conditioning . . . . . 185,261
Engine Oil . . . . . . . . . . 259,284
Flash-To-Pass . . . . . . . . . . . . 108
Flashers Hazard Warning . . . . . . . . . 240
Turn Signal . . . . . . . 53,107,154
Flooded Engine Starting . . . . . 192
Floor Console . . . . . . . . . . . . 143
Fluid Capacities . . . . . . . . . . . 283
Fluid Leaks . . . . . . . . . . . . . . 53
Fluid Level Checks Automatic Transmission . . . 270
Brake . . . . . . . . . . . . . . . . 269
Cooling System . . . . . . . . . 265
Engine Oil . . . . . . . . . . . . . 258
Fluid, Brake . . . . . . . . . . . . . 285
Fluids . . . . . . . . . . . . . . . . . . 284
Fluids, Lubricants and
Genuine Parts . . . . . . . . . . . . 284
Fog Lights . . . . . . . . . . . . . . 154
300