Oil LAND ROVER DEFENDER 1996 Repair Manual

33CLUTCH
2
FAULT DIAGNOSIS FAULT/SYMPTOM CHART
Symptoms
Slip Spin/Drag Judder/Fierce Fault Item
* * * Worn or oil on clutch linings 2
* * * Mechanical damage45678
* * Distorted clutch plate 2
* Failed or air in hydraulic system 12 13
* * Primary shaft tight fit in crankshaft bush 15 17
* Clutch splines sticking 2 15
* Weak clutch plate springs or insecure/worn
engine/gearbox mountings6
* Insecure/worn propeller shafts
* Insecure/worn suspension components/rubber
bushes
The items refered to in this chart relate to the clutch components shown in J6270 and J6271.See Description
and operation, Description
CLUTCH NOISE - MECHANICAL FAULTS
Noise from clutch or gearbox in neutral, which
disappears when clutch is depressed.
Suspect gearbox input/primary shaft bearings
See MANUAL GEARBOX, Fault diagnosis,
R380 gearbox
.
Noise from clutch or gearbox in neutral, which
changes tone or becomes worse when the clutch
is depressed.
Suspect worn release bearing.
Knocking/rattling from clutch or gearbox in
neutral, which is reduced or disappears when the
clutch is depressed.
Suspect worn/weak release lever retainer or
clutch unit.
Noise from clutch or gearbox in neutral, which
disappears when clutch is depressed.
Suspect gearbox fault
See MANUAL
GEARBOX, Fault diagnosis, R380 gearbox
.HYDRAULIC FAULTS
Unable to dis-engage clutch, little or no pedal
resistance.
1.Check condition, specification and level of fluid.
2.Check pipes and cylinders for leaks.
3.Check that air vent in reservoir lid is clear.
Suspect faulty master cylinder if no fluid leaks
present
See Repair, Master cylinder.
Spongy pedal operation
1.Check condition, specification and level of fluid.
2.Check that air vent in reservoir lid is clear.
Suspect air in fluid
See Repair, Bleed
hydraulic system
.
Clutch is difficult to dis-engage and/or does not
immediately re-engage when pedal is released.
1.Check condition, specification and level of fluid.
2.Check that air vent in reservoir lid is clear.
Suspect pedal pivot, master cylinder or slave
cylinder seizure
See Repair, Master cylinder.

33CLUTCH
2
OVERHAUL
18.Place coil spring over valve stem.
19.Insert retainer into spring.
20.Compress spring and engage valve stem in
keyhole slot in retainer.
21.Fit seal, large diameter last, to piston.
22.Insert piston into spring retainer and engage
locking prong.
23.Smear piston with suitable rubber grease and
insert assembly, valve end first, into cylinder.
24.Fit push-rod, retaining washer and circlip.
25.Fit clutch master cylinder to vehicle
See Repair,
Master cylinder
.SLAVE CYLINDER - OVERHAUL
Service repair no - 33.35.07
Dismantle
1.Remove slave cylinder
See Repair, Slave
cylinder
.
2.Withdraw dust cover.
3.Expel piston assembly, applying low pressure air
to fluid inlet.
4.Withdraw spring.
5.Remove seal from piston.
6.Remove bleed valve.
Inspection
7.Clean all components with new hydraulic fluid
fluid and allow to dry.
8.Examine cylinder bore and piston, ensure that
they are smooth to touch with no corrosion,
score marks or ridges. If there is any doubt, fit
new components.
9.Renew seal and dust cover from slave cylinder
overhaul kit.

MANUAL GEARBOX
1
DESCRIPTION AND OPERATION R380 GEARBOX
Description
The all synchromesh five speed manual gearbox unit,
is married to a two speed transfer gearbox.
All the gears, including reverse, run on needle roller
bearings and the main, layshaft and primary shafts
are supported by tapered roller bearings.The whole of the geartrain is lubricated through
drillings in the shafts, supplied by a low pressure
pump driven from the rear of the layshaft. The gear
change has a single rail selector and spool type
interlock. The main and transfer gearboxes ventilate
through nylon pipes, which terminate high up in the
engine compartment to prevent water entry when the
vehicle is operating in adverse conditions.
R380 Gearbox Components
1.Mainshaft 1st gear
2.Mainshaft 2nd gear
3.Mainshaft 3rd gear
4.Primary input shaft/4th gear
5.Mainshaft 5th gear
6.Layshaft
7.Mainshaft
8.Lubrication pump
9.Oil filter10.Ventilation pipe
11.Single rail gear shift
12.1st/2nd synchromesh
13.Oil seals
14.3rd/4th synchromesh
15.5th/reverse gear synchromesh
16.Selective spacers (mainshaft/layshaft end float)
17.Selective spacer (5th gear/reverse hub)

TRANSFER GEARBOX
1
FAULT DIAGNOSIS TRANSFER GEARBOX - OIL SEAL LOCATIONS
1.Input seal.
2.Cover plate joints.
3.Front output seal.
4.Front and rear housing joint faces.5.Rear output seal.
6.Power take off cover plate joint.
7.Bearing plate joint.

41TRANSFER GEARBOX
2
FAULT DIAGNOSIS OIL LEAKS
Verify that oil leak is from transfer box and not main
gearbox before proceeding with checks.
Prior to road test
1.Check oil level in transfer box is correct.
2.Check tightness of level and drain plugs.
3.Check breather system for blockage. To validate
system pipe must be removed, inspected,
rectified as necessary and refitted.
4.Remove all traces of oil from exterior of transfer
box.
Take vehicle for short road test.
5.Identify source of leaks and rectify as follows.
Front or rear output seal leaking:-
1.Drain oil and remove leaking output flange.
2.Inspect seal track on flange for surface damage.
If damaged renew component.
3.Remove and discard oil seal.
4.Inspect seal locating bore and remove any sharp
edges which may damage new oil seal.
5.Fit new seal.
6.Fit output flange and all other parts.
7.Add oil to correct level into gearbox
See
SECTION 10, Maintenance, Under vehicle
maintenance
.
Cover plate sealant leaking.
1.Drain oil and remove leaking cover plate.
2.Remove all traces of joint sealant from both joint
faces.
3.Degrease all components and apply a thin film of
Hylomar sealant, to both joint faces.
4.Apply thread sealant to bolts which come into
contact with gearbox oil.
5.Refit cover plate.
CAUTION: Care must be taken not to
overtighten fixings.Leak between main and transfer gearboxes.
1.Site vehicle onto a ramp .
2.Select neutral in transfer box and select 4th gear
in main gearbox.
3.Run engine at 2000 rpm with clutch/drive
engaged.
4.Observe joint between main and transfer boxes.
5.If oil leak is found establish if it is gear oil.
6.If so, leak is originating from transfer box.
7.Check two inner (main/transfer) bolts are oil
tight, as these holes are tapped into main
transfer case.
8.Remove transfer box to inspect mainshaft collar
seal track condition, and front face of transfer
case for porosity
See Repair, Transfer
gearbox
.
9.If these areas require servicing, transfer gearbox
input seal must also be renewed.
CAUTION: Avoid damaging new seal lip
and ensure seal is fitted flush with
machined face. Also ensure new seal is
not damaged when refitting transfer gearbox.
10.If red ATF type oil is seen leaking during
workshop test, investigate main gearbox for
cause of leak.
Detent plug or electrical switch leaks.
1.Detent plugs and electrical switches do not
usually leak. It must be noted that they fit into
open tapped holes in transfer case and therefore
should be considered when looking for source of
leak.

41TRANSFER GEARBOX
2
REPAIR
11.Remove 3 trim studs and lift up handbrake
gaiter.
12.Remove split pin, clevis pin, washer and
disconnect cable from handbrake lever. Ensure
handbrake is off.
13.Release handbrake outer cable from heelboard.
14.Remove fan cowl
See COOLING SYSTEM,
Repair, Fan cowl
.
15.Raise vehicle on ramp.
16.Drain transfer box oil
See SECTION 10,
Maintenance, Under vehicle maintenance
.
17.Remove intermediate silencer.
See MANIFOLD
AND EXHAUST SYSTEM, Repair,
Intermediate pipe - 90
orSee MANIFOLD
AND EXHAUST SYSTEM, Repair,
Intermediate pipe - 110/130
.
18.Mark rear propeller shaft drive flange and
transmission brake drum for reassembly.
19.Remove 4 nuts, disconnect propeller shaft from
brake drum, and tie aside.
20.Mark front propeller shaft drive flange and
transfer box output flange for reassembly.
21.Remove 4 nuts, disconnect propeller shaft from
transfer box, and tie aside.
22.Remove retaining clip at lower end of pivot arm
and disconnect differential lock control operating
rod.

41TRANSFER GEARBOX
4
REPAIR
36.Remove retaining nut, release clamp, and
disconnect speedometer cable from transfer
gearbox.
37.Remove battery earth strap retaining nut, 1 nut
and 4 bolts, securing transfer box to main
gearbox extension case.
38.Remove retaining nut securing earth leads to RH
side of transfer box.
39.Fit three guide studs,LRT-41-009, through
transfer box bolt holes to support it during
removal.
40.Lower hoist and withdraw transfer box from main
gearbox.
41.Remove transfer box.Refit
42.Ensure joint faces of transfer box and main
gearbox are clean and guide studs,LRT-41-009,
are fitted to extension case.
43.Lubricate oil seal in joint face of transfer box.
44.Secure transfer box to adaptor plate on lifting
hoist and raise hoist until transfer box can be
located over guide studs.
45.Remove guide studs, fit battery earth strap, and
secure transfer box to main gearbox extension
case. Tighten fixings to
45 Nm (33 lbf/ft).
46.Fit electrical leads to differential lock switch.
47.Raise hoist and remove wooden block
supporting main gearbox.
48.Secure LH and RH mounting brackets to
gearbox and tighten fixings to
55 Nm (41 lbf/ft).
49.With assistance and using a body jack between
chassis longitudinals, jack chassis sufficiently to
enable fitment of crossmember.
50.Position chassis crossmember and locate over
fixing studs of LH and RH gearbox mounting
rubbers .
51.Align crossmember and secure to chassis with 4
nuts and bolts on each side.
NOTE: Fit battery earth strap retaining clip
to LH top bolt.
52.Remove body jack.
53.Fit retaining nut to LH and RH mounting rubbers.
Tighten to
21 Nm (15 lbf/ft).
54.Remove 4 bolts securing hoist adaptor plate to
transfer box bottom cover.
55.Lower hoist and move aside.
56.Clean threads of the 4 bolts, coat with Loctite
290, and fit to transfer box bottom cover. Tighten
to
25 Nm (18 lbf/ft).
57.Fit earth leads to RH side of transfer box.
58.Connect differential lock control operating rod to
pivot arm.
59.Fit speedometer cable to transfer box.
60.Fit front and rear propeller shafts to transfer box.
Tighten nuts to
47 Nm (33 lbf/ft).
61.Fit intermediate silencer.See MANIFOLD AND
EXHAUST SYSTEM, Repair, Intermediate
silencer - 90; Refit
orSee MANIFOLD AND
EXHAUST SYSTEM, Repair, Intermediate
pipe - 110/130; Refit
.
62.Refill transfer box with recommended oil
See
SECTION 10, Maintenance, Under vehicle
maintenance

TRANSFER GEARBOX
1
SPECIFICATIONS, TORQUE REV: 05/99 TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
Transfer gearbox
Pinch bolt - operating arm to crank arm 9......................................................
End cover gear change housing 9.................................................................
Bottom cover to transfer case 25....................................................................
Front output housing to transfer case 25........................................................
Cross shaft housing to front output housing 25...............................................
Gear change housing 25.................................................................................
Pivot shaft to link arm 25.................................................................................
Connecting rod to adjustable clevis 25...........................................................
Anti-rotation plate intermediate shaft 25.........................................................
Front output housing cover 25........................................................................
Pivot bracket to extension housing 25............................................................
Finger housing to front output housing 25......................................................
Bearing housing to transfer case 25...............................................................
Brake drum to coupling flange 25...................................................................
Bearing housing cover to transfer gearbox 45................................................
Rear output speedometer housing to transfer gearbox 45..............................
Selector finger to cross shaft high/low 25.......................................................
Selector fork, high/low to shaft 25...................................................................
Transmission brake to speedometer housing 72............................................
Gate plate to grommet plate 9.......................................................................
Gearbox to transfer case 45...........................................................................
Oil drain plug 30..............................................................................................
Oil filler/level plug 30.......................................................................................
Differential case (front to rear) 60...................................................................
Output flanges 162...........................................................................................
Differential case rear stake nut 72..................................................................
Transfer breather 15.......................................................................................
Transfer box front drive flange to drive shaft 45..............................................
Transfer box rear drive flange to drive shaft 45..............................................
Transfer gearbox mounting brackets to chassis 30........................................
Mounting brackets to transfer gearbox 55......................................................
Mounting rubbers to mounting brackets 21.....................................................

PROPELLER SHAFTS
1
FAULT DIAGNOSIS VIBRATION HARSHNESS
Check that the propeller shaft universal joints and
sliding splines are not siezed or worn and that the
shafts are correctly aligned.
NOTE: In the event that both shafts are
satisfactory, but the vibration/harshness is
still present, the transfer box operation
and balance of the road wheels should be
checked.
For transfer box operation
See TRANSFER
GEARBOX, Fault diagnosis, Transfer Gearbox -
Oil seal locations
.
For balance of road wheels
See WHEELS AND
TYRES, Repair, Wheel Balancing.

REAR AXLE AND FINAL DRIVE
1
DESCRIPTION AND OPERATION DESCRIPTION
The welded steel rear axle casing houses a separate
spiral bevel type differential unit, which is off set to the
right of the vehicle centre line. The differential unit
drives the rear wheels via the axle shafts and fully
floating hubs which are mounted on tapered roller
bearings.
Lubrication
The differential is lubricated with oil and the hub
bearings with grease.The hub bearings are fitted with inner and outer seals.
The outer seals prevent the differential oil mixing with
the hub grease and the inner seals prevent dirt
ingress into the hub.
Ventilation
Ventilation of the hub bearings is through the outer oil
seals and the differential ventilation pipe, which
terminates at a high level.
Rear axle hub - 90
1.Axle casing
2.Ventilation pipe
3.Axle shaft
4.Wheel studs and hub
5.Wheel bearing stub axle6.Wheel bearings
7.Inner hub seal
8.Outer hub/axle shaft seal
9.Hub lock plate, thrust washer and nuts
10.Brake disc