mirror LAND ROVER DEFENDER 1996 Workshop Manual
[x] Cancel search | Manufacturer: LAND ROVER, Model Year: 1996, Model line: DEFENDER, Model: LAND ROVER DEFENDER 1996Pages: 455, PDF Size: 6.44 MB
Page 347 of 455
76CHASSIS AND BODY
26
REPAIR FRONT HEADLINING - 90 STATION WAGON
Service repair no - 76.64.10
Remove
1.Remove sun roof headlining finisher.
2.Remove sun visors
See Sun visors.
3.Remove interior lamp
See ELECTRICAL,
Repair, Interior lamp
.
4.Remove interior mirror and mounting plate
See
Interior mirror
.
5.Remove 4 retaining screws and detach both 'A'
post trims.
6.Remove caps and unscrew front seat belt fixing
bolts from 'B' posts.7.Carefully prise side trim panel cap fastener from
'B' posts.
8.Carefully prise 2 cap fasteners, from both sides,
securing headlining to body at door aperture.
9.Carefully prise out 5 cap fasteners securing front
and rear headlinings to roof.
10.From both sides, pull side trim panel inwards
enough to release rear corners of front
headlining.
11.Lower headlining and remove from vehicle.NOTE: Take care not to bend the
headlining on removal and refitting.
Refit
12.With assistance, raise headlining to roof.
13.Carefully pull side trim panel inwards, on both
sides, and slide headlining behind trim panel.
14.Position front headlining into recess of rear
headlining and secure both to roof mounting
brackets with 5 cap fasteners.
15.Secure both sides of front headlining to body at
door apertures with cap fasteners.16.Fit side cap fasteners at 'B' posts.
17.Secure seat belts to 'B' posts and tighten bolts to
32 Nm (24 lbf/ft).Fit caps to bolts.
18.Fit 'A' post trims.
19.Fit interior mirror
See Interior mirror.
20.Fit interior lamp
See ELECTRICAL, Repair,
Interior lamp
.
21.Fit sun visors
See Sun visors.
22.Fit sun roof headlining finisher.
Page 352 of 455
CHASSIS AND BODY
31
REPAIR INTERIOR MIRROR
Service repair no - 76.10.51
Remove
1.Prise interior mirror arm from mounting plate.
2.Remove 3 screws and remove mounting plate
from headlining.
Refit
3.Fit mounting plate to headlining.
4.Locate lower lug of mirror arm in mounting plate
aperture.
5.Press mirror arm firmly to engage spring clip in
mounting plate aperture.SUN VISORS
Service repair no - 76.10.47
Remove
1.Raise sun visor.
2.Remove 2 screws and collect sun visor.
Refit
3.Position sun visor and secure with 2 screws.
Page 415 of 455
ELECTRICAL
3
DESCRIPTION AND OPERATION Door and bonnet switches
Perimetric protection for the vehicle is provided by
ECU inputs connected to the starter switch, bonnet
switch and door switches.
Ultrasonic sensor
The ultrasonic sensor operates by emitting an air
pressure carrier wave which is subsequently received
by the sensor as it bounces back from objects inside
the vehicle. Once armed, the alarm will sound if wave
is disturbed by a door opening, or if movement is
detected inside the vehicle.
When the volumetric sensor is activated it monitors
movement within the vehicle for 15 seconds before
detecting and responding to intrusions. If the sensor
detects movement it delays arming until a quiet period
has lapsed; if continuous movement is detected, the
alarm will not arm volumetrically.
NOTE: Interior protection will not operate
until 15 seconds after alarm is set.
The ultrasonic sensor is positioned in a different
location, according to vehicle type, as follows:
·90/110 Station Wagon - RH cantrail trim
·90/110 Pick-up - On headlining, between interior
lamp and rear view mirror
·130 Crewcab - On headlining above RH door
Alarm sounder
Two types of alarm sounder can be fitted, one with a
battery back-up facility and or without battery back-up,
both providing an audible warning whenever the alarm
is triggered. The vehicle horn will also operate if the
alarm sounds.
The alarm sounder is fitted to LH inner front wing in
the engine compartment.
NOTE: Disconnecting the battery on
vehicles fitted with the battery backed-up
facility will result in the alarm sounding, if
correct procedure has not been followed.Engine immobilisation warning light
The engine immobilisation warning light is located on
the instrument panel, and provides a visual indication
that the engine is immobilised.
Anti-theft alarm indicator light
The anti-theft alarm indicator light is located on the
instrument panel, between the fuel and coolant
temperature indicators, and provides a visual
indication of the alarm/ immobiliser status.