service LAND ROVER DEFENDER 1996 Workshop Manual

AMENDMENT INSTRUCTION SHEET
DEFENDER WORKSHOP MANUAL
Publication Number LRL 0097 ENG (2nd Edition)
Amendment Number:LD002.99Date:05/99
To ensure that this manual is kept up to date and that a record of amendments to this manual is available, an
Amendment Instruction Sheet will be issued with each set of revised pages.
·The Title page of the Manual is re-issued, and the Part No. has been raised to the next edition. Except for the
Contents pages, all revised and new pages have the issue date at the foot of each page, together with an
indication of whether the pages are revised or new.
·This Amendment Instruction Sheet must be inserted at the front of the manual to indicate that the amendment
has been incorporated. Do not discard previous Amendment Instruction sheets.
·Your manual is only complete to this issue providing all prior Amendments are included.
·The filing instructions give section and page numbers affected. Additional pages or complete new sections may
be issued, insert the pages as instructed.
FILING INSTRUCTIONS
Section Discard Existing
PagesInsert New Pages Reason for Amendment
Title Page Title Page Title Page Part number raised to 3rd edition.
01 - Introduction Contents page Contents page Page numbers amended.
01 - Introduction -
InformationPages 1 and 4 Pages 1 and 4 Special service tools section amended.
04 - General
Specification DataPages 1, 4 and 11 Pages 1, 4, and 11 Correction of typographical errors.
09 - Lubricants, Fluids
and CapacitiesPages 1 to 3 Pages 1 to 3 New anti-freeze introduced.
10 - Maintenance Page 5, and pages
9to15Page 5, and pages
9to14Anti-freeze information updated, page layout
amended.
12 - Engine -
AdjustmentPage 1 Page 1 Warning amended to Caution.
12 - Engine -
Specifications, TorquePages 1 and 2 Pages 1 and 2 Page layout and torque figures amended.
19 - Fuel System -
RepairPages 7 and 9 Pages 7 and 9 Cross references amended.
26 - Cooling System -
RepairPage 4 Page 4 Cross reference amended.
37 - Manual Gearbox -
RepairPages 1 and 6 Pages 1 and 6 Cross references amended.
37 - Manual Gearbox -
Specifications, TorquePage 1 Page 1 Page layout amended.
41 - Transfer Gearbox -
RepairPage 5 Page 5 Correction of typographical error.

01INTRODUCTION
4
INFORMATIONREV: 05/99 ACCESSORIES AND CONVERSIONS
DO NOT FITunapproved accessories or conversions,
as they could affect the safety of the vehicle.
Land Rover will not accept liability for death, personal
injury, or damage to property which may occur as a
direct result of the fitting of non-approved conversions
to the vehicle.
WHEELS AND TYRES
WARNING: DO NOT replace the road
wheels with any type other than genuine
Land Rover wheels which are designed for
multi-purpose on and off road use and have very
important relationships with the proper operation
of the suspension system and vehicle handling.
Replacement tyres must be of the make and sizes
recommended for the vehicle, and all tyres must
be the same make, ply rating and tread pattern.
STEAM CLEANING
To prevent consequential rusting, any steam cleaning
within the engine bayMUSTbe followed by careful
re-waxing of the metallic components affected.
Particular attention must be given to the steering
column, engine coolant pipes and hose clips.
SPECIFICATION
The specification details and instructions set out in
this Manual apply only to a range of vehicles and not
to any one. For the specification of a particular vehicle
purchasers should consult their Dealer.
The Manufacturer reserves the right to vary
specifications with or without notice, and at such times
and in such manner as it thinks fit. Major as well as
minor changes may be involved in accordance with
the Manufacturer's policy of constant product
improvement.
Whilst every effort is made to ensure the accuracy of
the particulars contained in this Manual, neither the
Manufacturer or Dealer, by whom this Manual is
supplied, shall in any circumstances be held liable for
any inaccuracy or the consequences thereof.SPECIAL SERVICE TOOLS
The use of approved special service tools is
important. They are essential if service operations are
to be carried out efficiently, and safely. Where special
tools are specified,only these tools should be used
to avoid the possibility of personal injury or
damage to the components.Also, the amount of
time which they save can be considerable.
Special tools bulletins will be issued periodically giving
details of new tools as they are introduced.
All orders and enquiries from the United Kingdom
should be sent direct to Cartool (UK) Ltd. Overseas
orders should be placed with the local Cartool
distributor, where one exists. Countries where there is
no distributor may order direct from:
Cartool (UK) Ltd.
Unit 3,
Sterling Business Park,
Brackmills,
Northampton,
England, NN4 7EX.
The tools recommended in this Workshop Manual are
listed in an illustrated catalogue, obtainable from:
Land Rover Publications,
Character Mailing,
Heysham Road,
Bootle,
Merseyside, L70 1JL
COPYRIGHT
Ó1999 Rover Group Limited
All rights reserved. No part of this publication may be
produced, stored in a retrieval system or transmitted
in any form, electronic, mechanical, recording or other
means without prior written permission of Rover
Group.

01INTRODUCTION
6
INFORMATION 3.Position an axle stand under right hand axle
tube, carefully lower jack until axle sits securely
on both axle stands, remove trolley jack.
4.Before commencing work on underside of
vehicle re-check security of vehicle on stands.
5.Reverse procedure when removing vehicle from
stands.
Raise rear of vehicle
1.Position cup of hydraulic arm under differential
casing.
2.Raise vehicle to enable axle stands to be
installed under left and right hand axle tubes.
3.Lower jack until axle sits securely on axle
stands, remove trolley jack.
4.Before commencing work on underside of
vehicle re-check security of vehicle on stands.
5.Reverse procedure when removing vehicle from
stands.
HYDRAULIC VEHICLE RAMP (FOUR POST)
Use only a 'drive on' type ramp which supports vehicle
on its road wheels. If a 'wheel-free' condition is
required, use a 'drive on' ramp incorporating a
'wheel-free' system providing support beneath axle
casings. Alternatively, place vehicle on a firm, flat floor
and support on axle stands.
TWO POST VEHICLE RAMPS
The manufacturer of LAND ROVER VEHICLES
DOES NOT recommend using 'Two Post' ramps
that employ four adjustable support arms. These
are NOT considered safe for Land Rover vehicles.
If vehicle is installed on a Two Post ramp
responsibility for safety of vehicle and personnel
performing service operations is in the hands of
the Service Provider.DYNAMOMETER TESTING
The front and rear axles cannot be driven
independently.
WARNING: DO NOT attempt to drive
individual wheels with vehicle supported
on floor jacks or stands.
Four wheel dynamometers
Provided that front and rear dynamometer rollers are
rotating at identical speeds and that normal workshop
safety standards are applied, there is no speed
restriction during testing except any that may apply to
the tyres.
Two wheel dynamometers
IMPORTANT: Use a four wheel dynamometer for
brake testing if possible.
If brake testing on a single axle rig is necessary it
must be carried out with propeller shaft to rear axle
removed, AND neutral selected in BOTH main
gearbox and transfer gearbox. When checking brakes,
run engine at idle speed to maintain servo vacuum.
If checking engine performance, the transfer box must
be in high range and propeller shaft to stationary axle
must be removed.

INTRODUCTION
13
INFORMATION FAULT DIAGNOSTIC EQUIPMENT
TESTBOOK
For Defender models fitted with the vehicle Anti-theft
Immobilisation and Alarm System, diagnostic
equipment, named TestBook, is available to assist in
the diagnostic and fault finding abilities of the Dealer
workshop. A diagnostic connector, located under the
front centre seat, or cubby box, as shown below, is
provided to facilitate the procedures.
If an exhaust gas recirculation (EGR) system is fitted,
this too can be checked using TestBook. A diagnostic
connector, also located under the front centre seat or
cubby box, is provided.
Features of Testbook include :-
Fully upgradable support for the technician.
Structured diagnostics to accommodate all skill levels.
Touch screen operation.
Direct print out of screen information and test results.READING THIS MANUAL
This manual is divided into sections shown on the
contents page, alongside a range of icons, familiar to
service technicians.
Relevant information is contained within each of these
sections. These are further divided into the following
sub-sections which appear at the foot of each page :-
Description and operation.
Fault diagnosis.
Adjustment.
Repair.
Overhaul.
Specifications, Torque.
To avoid repeating information through the sections,
where part of the repair operation impacts on another
section, a cross reference is given to direct the reader
to where the information is sited.
For example:
The maintenance section states the need to renew
drive belt. A cross reference sites this information in:
Section 12 Engine
- Sub-section: Repairs
- Heading: Drive belt renew.

04GENERAL SPECIFICATION DATA
6
INFORMATION SHOCK ABSORBERS
Type Telescopic, double-acting non-adjustable.................................................................................
Bore diameter 35.47mm...................................................................
BRAKES
Front service brake
Caliper AP Lockheed, four opposed pistons..............................................................................
Operation Hydraulic, self adjusting.........................................................................
Disc 90 - Solid, outboard, 110/130 - Ventilated, outboard..................................................................................
Disc diameter 298 mm (11.73 in)...................................................................
Disc thickness 90 - 14,1 mm (0.56in), 110/130 - 24mm (0.95 in)..................................................................
Wear limit 1 mm (0.04in) per side of disc.........................................................................
Disc run-out maximum 0,15mm (0.006 in).....................................................
Pad area 58 cm
2(9.0 in2) ..........................................................................
Total swept area 801,3 cm2(124.2 in2) ...............................................................
Pad material Ferodo 3440 non asbestos.....................................................................
Pad minimum thickness 3 mm (0.12in)...................................................
Rear service brake
Caliper AP Lockheed opposed piston..............................................................................
Operation Hydraulic, self adjusting.........................................................................
Disc Solid, outboard..................................................................................
Disc diameter 90 - 290 mm (11.42 in), 110/130 - 298 mm (11.73)...................................................................
Disc thickness 90 - 12,5 mm (0.49 in), 110/130 - 14,1 mm (0.56 in)..................................................................
Wear limit 90 - 0,38 mm (0.015 in), 110/130 - 1,0 mm (0.04 in).........................................................................
per side of disc
Disc run-out maximum 0,15 mm (0.006 in).....................................................
Pad area 90 - 30,5 cm
2(4.37 in2), 110/130 - 36,2 cm2(5.61 in2) ..........................................................................
Total swept area 90 - 694 cm2(106.98 in2) ...............................................................
Pad material Ferodo 3440 non asbestos.....................................................................
Pad minimum thickness 3 mm (0.12 in)...................................................
Parking brake
Type Mechanical, cable operated drum brake on the rear of.................................................................................
the transfer gearbox output shaft
Drum internal diameter 254 mm (10.0 in).....................................................
Width 70 mm (2.75 in)................................................................................
Pad material Ferodo 3611 non asbestos.....................................................................
Servo/master cylinder
Manufacturer Lucas....................................................................
Servo type LSC 80........................................................................
Master cylinder type 25,4 mm (1.0 in) diameter, tandem.........................................................
Pressure reducing valve, failure conscious Cut-in pressure, 90 - 24 bar (360 Ibf/in
2) ratio 4.0:1, ......................
110 - 43 bar (645 Ibf/in2) ratio 2.9:1*
NOTE: * Pressure reducing valves are not fitted to all 110 specifications.

GENERAL SPECIFICATION DATA
7
INFORMATION AIR CONDITIONING
System CFC free expansion valve system.............................................................................
Compressor Sanden TRS105N.....................................................................
Refrigerant R134a CFC free.......................................................................
Charge quantity 1.1 Kg................................................................
WIPER MOTORS
Tailgate wiper motor
Make/type IMOS (non-serviceable)........................................................................
Running current, wet screen at 20°C ambient 1.0 to 2.8 amps.................
Wiper speed, wet screen at 20°C ambient 37 to 43 cycles per minute.......................
Windscreen wiper motor
Make/type Lucas 14W uprated two speed........................................................................
Armature end float 0,1 to 0,2 mm............................................................
Brush length, minimum 4,8 mm....................................................
Brush spring tension 140 to 200 g........................................................
Resistance of armature winding
at 16ÊC (69ÊF) measured between adjacent
commutatator segments 0.23 to 0.35 ohms...................................................
Light running, rack disconnected: current at 13.5 V 2.0 amps.........
Wiper speed, wet screen, 60 seconds from cold Low speed - 45±3 rev/min, High speed - 65±5 ..............
rev/min
ELECTRICAL
System 12 volt, negative ground.............................................................................
Battery
Make/type - standard Land Rover Parts and Equipment/Lucas maintenance.......................................................
free 9-plate 072
Make/type - heavy duty Land Rover Parts and Equipment/Lucas maintenance....................................................
free 14-plate 663
Generator
Manufacturer Magnetti Marelli....................................................................
Type A127 - 100amp.................................................................................
Polarity Negative ground.............................................................................
Brush length:
New 17 mm.........................................................................
Worn, minimum free protrusion from moulding 5 mm........
Brush spring pressure flush with moulding 1.3N to 2.7N......................
Regulator voltage 13.6 to 14.4 volts.............................................................
Nominal output
Generator speed 6000 rev/min.....................................................
Control voltage 14 volt........................................................
Amp 65 amp.........................................................................

ENGINE TUNING DATA
1
INFORMATION 300 Tdi ENGINE
Type2.5 Litre Turbo diesel intercooled .................................................................................
Firing order1-3-4-2 .....................................................................
Injection timing1,54 mm lift at T.D.C. ...............................................................
Injection timing with electronic EGR1,40 mm lift at T.D.C. ............................
Timing marks:
Valve timing - manual Slot for pin in flywheel and TDC mark on front pulley........................................................
Injection timing Timing pin (service tool).................................................................
Tappet clearances inlet and exhaust 0,20 mm cold...............................
Valve timing: Inlet Exhaust
- Opens 16°B.T.D.C. ............................................................................ 51°B.B.D.C.
- Closes 42°A.B.D.C. ............................................................................ 13°A.T.D.C.
- Peak 103°A.T.D.C. ............................................................................... 109°B.T.D.C.
- Lift 9,67 mm.................................................................................. 9,97 mm
Maximum governed speeds:
- No load (neutral/full throttle) 4600 + 40 - 120 rev/min...........................................
- Idle speed at running temperature 720±20 rev/min .................................
- Die-down time 4 seconds................................................................
INJECTION PUMP
Make & type - standard Bosch rotary R509 type with boost control and two....................................................
speed mechanical governor with auto advance and
solenoid electrical shut-off. Tamper proof sealing on,
no load governed speed and fuel adjustment screws.
Constant volume delivery valves
Make & type - Electronic EGR Bosch rotary R509/1 type with boost control and two.........................................
speed mechanical governor with auto advance and
solenoid electrical shut-off. Tamper proof sealing on
flight speed and fuel adjustment screws. Constant
volume delivery valves. Throttle position sensor for
EGR control.
HEATER PLUGS
Make & type Probe type, No.0100226129A Beru 12 volts.....................................................................
Time to reach operating temperature of 850°C 8 seconds...............

GENERAL FITTING REMINDERS
1
INFORMATION GENERAL FITTING REMINDERS
WORKSHOP SAFETY IS YOUR RESPONSIBILITY!
The suggestions, cautions and warnings in the
section are intended to serve as reminders for
trained and experienced mechanics. This manual
is not a definitive guide to automotive mechanics
or workshop safety.
Shop equipment, shop environment, and the use
and disposal of solvents, fluids, and chemicals
are subject to government regulations which are
intended to provide a level of safety. It is your
responsibility to know and comply with such
regulations.
PRECAUTIONS AGAINST DAMAGE
1.Always fit covers to protect fenders before
commencing work in engine compartment.
2.Cover seats and carpets, wear clean overalls
and wash hands or wear gloves before working
inside vehicle.
3.Avoid spilling hydraulic fluid or battery acid on
paint work. Wash off with water immediately if
this occurs. Use Polythene sheets to protect
carpets and seats.
4.Always use a recommended Service Tool where
specified.
5.Protect temporarily exposed screw threads by
replacing nuts or fitting plastic caps.SAFETY PRECAUTIONS
1.Whenever possible, use a lift when working
beneath vehicle, in preference to jacking. Chock
wheels as well as applying parking brake.
WARNING: Do not use a pit when
removing fuel system components.
2.Never rely on a jack alone to support vehicle.
Use axle stands carefully placed at jacking
points to provide rigid support.
3.Ensure that a suitable form of fire extinguisher is
conveniently located.
4.Check that any lifting equipment used has
adequate capacity and is fully serviceable.
5.Disconnect battery.
WARNING: Do not disconnect any pipes in
air conditioning system, unless trained
and instructed to do so. A refrigerant is
used which can cause blindness if allowed to
contact eyes.
6.Ensure that adequate ventilation is provided
when volatile degreasing agents are being used.
7.Do not apply heat in an attempt to free stiff
fixings; as well as causing damage to protective
coatings, there is a risk of damage to electronic
equipment and brake linings from stray heat.

07GENERAL FITTING REMINDERS
2
INFORMATION PREPARATION
1.Clean components and surrounding area prior to
removal.
2.Blank off any openings exposed by component
removal using greaseproof paper and masking
tape.
3.Immediately seal fuel, oil or hydraulic lines when
separated, using plastic caps or plugs, to
prevent loss of fluid and entry of dirt.
4.Close open ends of oilways, exposed by
component removal, with tapered hardwood
plugs or readily visible plastic plugs.
5.Immediately a component is removed, place it in
a suitable container; use a separate container for
each component and its associated parts.
6.Before dismantling a component, clean it
thoroughly with a recommended cleaning agent;
check that agent is suitable for all materials of
component.
7.Clean bench and provide marking materials,
labels, containers and locking wire before
dismantling a component.
DISMANTLING
1.Observe scrupulous cleanliness when
dismantling components, particularly when
brake, fuel or hydraulic system parts are being
worked on. A particle of dirt or a cloth fragment
could cause a dangerous malfunction if trapped
in these systems.
2.Blow out all tapped holes, crevices, oilways and
fluid passages with an air line. Ensure that any
O-rings used for sealing are correctly replaced or
renewed, if disturbed.
3.Use marking ink to identify mating parts, to
ensure correct reassembly. If a centre punch or
scriber is used they may initiate cracks or
distortion of components.
4.Wire together mating parts where necessary to
prevent accidental interchange (e.g. roller
bearing components).
5.Wire labels on to all parts which are to be
renewed, and to parts requiring further
inspection before being passed for reassembly;
place these parts in separate containers from
those containing parts for rebuild.
6.Do not discard a part due for renewal until it has
been compared with the new part, to ensure that
its correct replacement has been obtained.INSPECTION-GENERAL
1.Never inspect a component for wear or
dimensional check unless it is absolutely clean;
a slight smear of grease can conceal an incipient
failure.
2.When a component is to be checked
dimensionally against figures quoted for it, use
correct equipment (surface plates, micrometers,
dial gauges, etc.) in serviceable condition.
Makeshift checking equipment can be
dangerous.
3.Reject a component if its dimensions are outside
limits quoted, or if damage is apparent. A part
may, however, be refitted if its critical dimension
is exactly limit size, and is otherwise satisfactory.
4.Use 'Plastigauge' 12 Type PG-1 for checking
bearing surface clearances. Directions for its
use, and a scale giving bearing clearances in
0,0025 mm steps are provided with it.

GENERAL FITTING REMINDERS
3
INFORMATION BALL AND ROLLER BEARINGS
CAUTION: Never refit a ball or roller
bearing without first ensuring that it is in a
fully serviceable condition.
1.Remove all traces of lubricant from bearing
under inspection by washing in a suitable
degreaser; maintain absolute cleanliness
throughout operations.
2.Inspect visually for markings of any form on
rolling elements, raceways, outer surface of
outer rings or inner surface of inner rings. Reject
any bearings found to be marked, since any
marking in these areas indicates onset of wear.
3.Holding inner race between finger and thumb of
one hand, spin outer race and check that it
revolves absolutely smoothly. Repeat, holding
outer race and spinning inner race.
4.Rotate outer ring gently with a reciprocating
motion, while holding inner ring; feel for any
check or obstruction to rotation, and reject
bearing if action is not perfectly smooth.
5.Lubricate bearing generously with lubricant
appropriate to installation.
6.Inspect shaft and bearing housing for
discolouration or other marking suggesting that
movement has taken place between bearing and
seatings. (This is particularly to be expected if
related markings were found in operation 2).
7.Ensure that shaft and housing are clean and free
from burrs before fitting bearing.8.If one bearing assembly of a pair shows an
imperfection it is generally advisable to replace
both with new bearings; an exception could be
made if the faulty bearing had covered a low
mileage, and it could be established that
damage was confined to it only.
9.When fitting bearing to shaft, apply force only to
inner ring of bearing, and only to outer ring when
fitting into housing, as shown above.
10.In the case of grease lubricated bearings (e.g.
hub bearings) fill space between bearing and
outer seal with recommended grade of grease
before fitting seal.
11.Always mark components of separable bearings
(e.g. taper roller bearings) in dismantling, to
ensure correct reassembly. Never fit new rollers
in a used outer ring, always fit a complete new
bearing assembly.