spare wheel LAND ROVER DEFENDER 1996 Workshop Manual

10MAINTENANCE
2
MAINTENANCE BATTERY CONNECTIONS
NOTE: The vehicle may be fitted with an
alarm and immobilisation system using a
battery backed-up alarm sounder.
See
ELECTRICAL, Repair, Battery
Disconnect battery leads, clean and grease with
petroleum jelly, including battery terminals.
CHECK OPERATION OF DOOR SWITCHES
When a Vehicle Immobilisation and Alarm System is
fitted it is important that all door and bonnet switches
operate correctly, otherwise perimeter and interior
protection may not function if a door or the bonnet is
opened.VEHICLE EXTERIOR
CHECK/ADJUST HEADLAMP ALIGNMENT
Check/adjust headlamp alignment.
CHECK ROAD WHEELS AND TYRES
Check road wheels for damage.
Check tyres, including spare, for compliance with
manufacture's specificaton.
Check visually for cuts, lumps, bulges, uneven tread
wear and tread depth.
See INTRODUCTION,
Information, wheels and tyres
Check/adjust tyre pressures.See WHEELS AND
TYRES, Repair, Tyres pressures
INSPECT BRAKE PADS FOR WEAR, CALIPERS
FOR LEAKS AND CONDITION OF DISCS
Check thickness of brake pads, and renew if thickness
is less than 3,00 mm (0.12 in). Check brake pads for
oil contamination and fit a new set, if necessary,
See
BRAKES, Repair, front brake pads
orSee
BRAKES, Repair, rear brake pads
WARNING: When renewing brake pads, it
is essential that only genuine components
with correct grade of lining are used.
Always fit new pads as complete axle sets, NEVER
individually or as a single wheel set. Serious
consequences could result from out of balance
braking due to mixing of linings.
CHECK FRONT WHEEL ALIGNMENT
Use recognised wheel alignment equipment to carry
out this operation.
See STEERING, Adjustment,
front wheel alignment
CHECK OPERATION OF ALL DOORS/TAILGATE,
BONNET AND LOCKS
LUBRICATE ALL DOOR/TAILGATE HINGES, AND
DOOR CHECK/LOCK MECHANISMS

WHEELS AND TYRES
1
REPAIR REV: 05/99 GENERAL INFORMATION
WARNING: This is a multi-purpose vehicle
with wheels and tyres designed for both
on and off road usage. Only use wheels
and tyres specified for use on the vehicle.
The vehicle is equipped with tubeless 'S','T' or 'H'
rated radial ply tyres as standard equipment. The
tyres are of European metric size and must not be
confused with the "P" size metric tyres available in
North America.
Vehicle wheel sets, including spare wheel, must be
fitted with the same make and type of tyre to the
correct specification and tread pattern. Under no
circumstances must cross-ply or bias-belted tyres be
used.
For tyre specification and pressures
See GENERAL
SPECIFICATION DATA, Information, Wheels and
Tyres
.
Steel wheels
Tubeless tyres are mounted on 7.0 inch wide by 16
inch diameter steel wheels.
Alloy Wheels
Tubeless tyres are mounted on 7.0 inch wide by 16
inch diameter cast aluminium alloy wheels. The
surface has a paint finish covered with a clear
polyurethane lacquer. Care must be taken when
handling the wheel to avoid scratching or chipping the
finish.
The alloy wheel rim is of the asymmetric hump
type incorporating a safety hump to improve
location of the tyre bead in its seat. If difficulty is
experienced in fitting tyres to this type of rim
See
Tyre Fitting
.
WARNING: DO NOT fit an inner tube to an
alloy wheel.TYRE INSPECTION
Inspect tyres at weekly intervals to obtain maximum
tyre life and performance and to ensure compliance
with legal requirements. Check for signs of incorrect
inflation and uneven wear, which may indicate a need
for balancing or front wheel alignment,
See Fault
diagnosis, Tyre Wear Chart
, if the tyres have
abnormal or uneven wear patterns.
Check tyres at least weekly for cuts, abrasions, bulges
and for objects embedded in the tread. More frequent
inspections are recommended when the vehicle is
regularly used in off road conditions.
To assist tyre inspection, tread wear indicators are
moulded into the bottom of the tread grooves, as
shown in the illustration above.
When the tread has worn to a depth of 1.6 mm the
indicators appear at the surface as bars which
connect the tread pattern across the width of the tread
as shown in the illustration above.

74WHEELS AND TYRES
2
REPAIRREV: 05/99 When the indicators appear in two or more adjacent
grooves, at three locations around the tyre, a new tyre
must be fitted.
NOTE: DO NOT attempt to interchange
tyres, e.g. from front to rear, as tyre wear
produces characteristic patterns
depending on their position. If tyre position is
changed after wear has occured, the performance
of the tyre will be adversely affected.
NOTE: Territorial vehicle regulations
governing tyre wear MUST be adhered to.
WHEELS INSPECTION
Regularly check the condition of the wheels. Replace
any wheel that is bent, cracked, dented or has
excessive runout.
VALVES INSPECTION
Check condition of inflation valve. Replace any valve
that is worn, cracked, loose, or leaking air.TYRE PRESSURES
Maximum tyre life and performance will be
obtained only if tyres are maintained at the correct
pressures.
Tyre pressures must be checked at least once a week
and preferably daily, if the vehicle is used off road.
The tyre inflation pressure is calculated to give the
vehicle satisfactory ride and steering characteristics
without compromising tyre tread life. For
recommended tyre pressures in all conditions
See
GENERAL SPECIFICATION DATA, Information,
Wheels and Tyres
.
Always check tyre inflation pressures using an
accurate gauge and inflate tyres to the
recommended pressures only.
Check and adjust tyre pressuresONLYwhen the
tyres are cold, vehicle parked for three hours or more,
or driven for less than 3.2 km (2 miles) at speeds
below 64 km/h (40 mph). Do not reduce inflation
pressures if the tyres are hot or the vehicle has been
driven for more than 3.2 km (2 miles) at speeds over
64 km/h (40 mph), as pressures can increase by 0.41
bars (6 lb/in
2) over cold inflation pressures.
CheckALLtyre pressures including the spare. Refit
the valve caps as they form a positive seal and keep
dust out of the valve.

WIPERS AND WASHERS
9
REPAIR 13.Fit wheelboxes to bulkhead.
14.Fit drive tubes to wheelboxes.
15.Feed drive rack through tubes until fully seated
in both wheelboxes.
16.Secure drive tube nut to wiper motor.
17.Fit wiper motor strap and earth lead.
18.When all components are correctly aligned, fully
tighten wheelboxes nuts to secure drive tubes.
Tighten wheelbox to bulkhead nuts.
19.Fully tighten drive tube nut to wiper motor and
motor strap screws.
20.Connect multiplug to wiper motor and earth lead
to strap tag.
21.Fit spacer, where used, early vehicles only.
22.Fit wiper arm adaptors.
23.Reconnect battery and check operation of wiper
motor and drive assembly and wheelboxes.
24.Disconnect battery.
25.Fit steering column upper and lower supports.
Tighten fixings to correct torque.
26.Fit demister vent top duct.
27.Secure RH demister vent and hose.
28.Fit LH and RH demister vents to ducts.
29.Fit centre and LH fascia top crash rail support
brackets.
30.Fit all other components removed to gain access
to wiper motor and wheelboxes.
31.Reconnect battery, check wiper motor operation
again and adjust wiper arms, if necessary.REAR WIPER MOTOR
Service repair no - 84.35.12
Remove
1.With assistance, unscrew 3 retaining nuts and
remove spare wheel from rear door mounting
studs.
2.Lift wiper arm end cap to gain access to securing
nut.
3.Remove nut and withdraw wiper arm from drive
spindle.
4.Remove retaining nut, plain washer and rubber
washer securing wiper motor drive spindle to
door.
5.Remove 2 screws and remove cover from wiper
motor mounting bracket.
6.Disconnect wiper motor harness multi-plug.
7.Remove bolt, with rubber washer, and detach
wiper motor, complete with mounting bracket,
from rear door.

84WIPERS AND WASHERS
10
REPAIR Refit
8.Locate wiper motor drive spindle through
aperture in rear door.
9.Position wiper motor mounting bracket and
secure to rear door. Tighten bolt to
23 Nm (17
lbf/ft).
10.Reconnect harness multi-plug.
11.Secure drive spindle to door.
12.Fit wiper motor cover.
13.Fit rear wiper arm.
14.Fit spare wheel. Tighten retaining nuts to
130Nm
(96 lbf/ft).