transmission oil LAND ROVER DEFENDER 1996 Workshop Manual

GENERAL SPECIFICATION DATA
3
INFORMATION FUEL SYSTEM
Fuel lift pump type Mechanical with hand primer............................................................
Fuel lift pump pressure 42 - 55 Kgf/cm
2(3 - 4 lbf/in2) at 1800 rpm .....................................................
Fuel filter Paper element in disposable canister..........................................................................
Air cleaner Paper element type........................................................................
COOLING SYSTEM
System type Pressurised, spill return, thermostatically controlled.....................................................................
water and anti freeze mixture. Pump assisted thermo
syphon. Coolant radiator combined with oil cooler and
turbo intercooler.
Cooling fan 11 blade axial flow 433 mm diameter, 1.29:1 drive.......................................................................
ratio, with viscous coupling.
Pump type Centrifugal, impellor, belt driven........................................................................
Thermostat opening 88°C .........................................................
Expansion tank cap pressure 1,06 Kgf/cm
2(15 Ibf/in2) (system pressure) ...........................................
CLUTCH
Type Valeo diaphragm spring.................................................................................
Centre plate diameter 235 mm.......................................................
Facing material Verto F202 grooved.................................................................
Release bearing Ball journal...............................................................
TRANSMISSION
Main gearbox
Type R380 Single helical constant mesh.......................................................................
Speeds 5 forward, 1 reverse, all synchromesh.............................................................................
Transfer box
Type LT230 Two speed reduction on main gearbox output. Front......................................................................
and rear drive permanently engaged via a lockable
differential
Rear axle
Type Spiral bevel, fully floating shafts.................................................................................
Ratio 3.54:1.................................................................................

CLUTCH
1
FAULT DIAGNOSIS CLUTCH ASSEMBLY CONDITIONS
For the clutch to operate correctly it is important the
following conditions are satisfied:-
·The primary shaft (15) must be free in the
crankshaft spigot bush (17).
·The friction plate (2) must be able to slide easily on
the splines on the primary shaft (15), to a position
where it does not contact either the flywheel or the
pressure plate.
·The friction plate must not be distorted or the
linings contaminated with oil, which may cause it to
stick or continue to run in contact with the flywheel
or pressure plate.
A number of faults can develop in the operation of the
clutch for a variety of reasons and most faults are due
to normal wear at high mileage. Problems can also
occur if the unit has been renewed by an unskilled
operator.
Recognising and diagnosing a particular clutch fault is
therefore of paramount importance in ensuring that
the problem is rectified at the first attempt.
Problems which develop in the clutch are as follows:-
·Clutch spin/drag
·Clutch slip
·Clutch judder/fierceCLUTCH SPIN - DRAG
Symptoms
Clutch spin is that, with engine running and clutch
pedal depressed, the gears cannot be immediately
engaged without making a grinding noise. This
indicates the clutch is not making a clean break.
However, if the clutch pedal is held depressed for
several seconds the friction plate will eventually break
free from the engine and the gear will engage silently.
Clutch spin as it becomes more severe develops into
clutch drag, making the silent engagement of a gear
impossible, regardless of how long the pedal is held
depressed.
CLUTCH SLIP
Symptoms
Clutch slip is most evident climbing a hill or when the
vehicle is moving off from stationary with a heavy
load. As the clutch is released, slip occurs between
the engine and the transmission, allowing the engine
speed to increase without a corresponding increase in
vehicle speed.
Clutch slip can develop to the stage where no power
is transmitted through the clutch as the pedal is
released.
CLUTCH JUDDER - FIERCE
Symptoms
Clutch judder or fierce engagement, like slip, is most
likely to occur when the vehicle is moving off from
stationary. As the clutch pedal is released the vehicle
will move rapidly or in a series of jerks, which cannot
be controlled even by careful operation of the clutch
by the driver.
It should be noted that a vehicle may display all the
symptoms or any combination of the symptoms
described, depending on the driving conditions vehicle
load and operating temperatures.

41TRANSFER GEARBOX
2
REPAIR
11.Remove 3 trim studs and lift up handbrake
gaiter.
12.Remove split pin, clevis pin, washer and
disconnect cable from handbrake lever. Ensure
handbrake is off.
13.Release handbrake outer cable from heelboard.
14.Remove fan cowl
See COOLING SYSTEM,
Repair, Fan cowl
.
15.Raise vehicle on ramp.
16.Drain transfer box oil
See SECTION 10,
Maintenance, Under vehicle maintenance
.
17.Remove intermediate silencer.
See MANIFOLD
AND EXHAUST SYSTEM, Repair,
Intermediate pipe - 90
orSee MANIFOLD
AND EXHAUST SYSTEM, Repair,
Intermediate pipe - 110/130
.
18.Mark rear propeller shaft drive flange and
transmission brake drum for reassembly.
19.Remove 4 nuts, disconnect propeller shaft from
brake drum, and tie aside.
20.Mark front propeller shaft drive flange and
transfer box output flange for reassembly.
21.Remove 4 nuts, disconnect propeller shaft from
transfer box, and tie aside.
22.Remove retaining clip at lower end of pivot arm
and disconnect differential lock control operating
rod.

TRANSFER GEARBOX
1
SPECIFICATIONS, TORQUE REV: 05/99 TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
Transfer gearbox
Pinch bolt - operating arm to crank arm 9......................................................
End cover gear change housing 9.................................................................
Bottom cover to transfer case 25....................................................................
Front output housing to transfer case 25........................................................
Cross shaft housing to front output housing 25...............................................
Gear change housing 25.................................................................................
Pivot shaft to link arm 25.................................................................................
Connecting rod to adjustable clevis 25...........................................................
Anti-rotation plate intermediate shaft 25.........................................................
Front output housing cover 25........................................................................
Pivot bracket to extension housing 25............................................................
Finger housing to front output housing 25......................................................
Bearing housing to transfer case 25...............................................................
Brake drum to coupling flange 25...................................................................
Bearing housing cover to transfer gearbox 45................................................
Rear output speedometer housing to transfer gearbox 45..............................
Selector finger to cross shaft high/low 25.......................................................
Selector fork, high/low to shaft 25...................................................................
Transmission brake to speedometer housing 72............................................
Gate plate to grommet plate 9.......................................................................
Gearbox to transfer case 45...........................................................................
Oil drain plug 30..............................................................................................
Oil filler/level plug 30.......................................................................................
Differential case (front to rear) 60...................................................................
Output flanges 162...........................................................................................
Differential case rear stake nut 72..................................................................
Transfer breather 15.......................................................................................
Transfer box front drive flange to drive shaft 45..............................................
Transfer box rear drive flange to drive shaft 45..............................................
Transfer gearbox mounting brackets to chassis 30........................................
Mounting brackets to transfer gearbox 55......................................................
Mounting rubbers to mounting brackets 21.....................................................

74WHEELS AND TYRES
6
REPAIRREV: 05/99 WHEELS
Remove
WARNING: The parking brake acts on
transmission, not rear wheels, and may
not hold vehicle when jacking unless
following procedure is used. If one front wheel
and one rear wheel is raised no vehicle holding or
braking effect is possible. Wheels MUST be
chocked in all circumstances.
Apply parking brake, select a gear in main
gearbox and engage low gear in transfer box.
1.Loosen 5 wheel nuts.
2.Using a suitable trolley jack, raise vehicle and
place on axle stands
See INTRODUCTION,
Information, Jacking
.
3.Remove wheel nuts and carefully withdraw
wheel over studs.
Refit
4.Ensure that retaining studs and nuts are clean.
5.Alloy wheels: Lightly coat wheel mounting spigot
face with a suitable anti-seize compound to
minimise possibility of adhesion between wheel
and spigot face.
6.Refit wheel taking care not to damage stud
threads. (Do not apply oil).
7.Fit wheel nuts and turn by hand for at least three
full threads before using any form of wheel
wrench.
8.Tighten nuts as much as possible using a
suitable wrench.
9.Lower vehicle and finally tighten nuts to correct
torque sequence shown.
Alloy wheels -
130 Nm (96 lbf/ft)
Steel wheels -100 Nm (80 lbf/ft)
Heavy duty wheels -170 Nm (125 lbf/ft)