dimensions LAND ROVER DEFENDER 1999 User Guide

77PANEL REPAIRS
2
BODY DIMENSIONS CHASSIS FRAME ALIGNMENT
With the vehicle assembled, a check for chassis
squareness can be made as follows:
1.Place the vehicle on a level floor.
2.Mark measuring points at approximately the
locations shown in LR4412M ensuring that the
marks are exactly opposite on each side of the
chassis frame.3.Hold a plumb line against each of the measuring
points in turn and mark the floor directly beneath
the plumb-bob.
4.Move the vehicle and measure diagonally
between the marks made on the floor, if the
chassis is square the diagonals between the
related measuring points should be within 9,50
mm.
5.Chassis frame dimensional checks can be
made, with the vehicle upper structure removed,
referring to the applicable illustration and
associated key.
ProCarManuals.com

PANEL REPAIRS
3
BODY DIMENSIONS LAND ROVER 90 CHASSIS
ProCarManuals.com

77PANEL REPAIRS
4
BODY DIMENSIONS LAND ROVER 90
CHASSIS ALIGNMENT DIMENSIONS
A - Front Datum
B - Chassis Datum
C - Front axle centre line
D - Rear axle centre line
1.239,0 - 236,5 mm
2.82,0 - 79,5 mm
3.633 mm
4.2420,6 - 2418,6 mm
5.2306,4 - 2305,4 mm
6.981,2 - 978,7 mm
7.182,7 mm
8.41,5 - 37,0 mm
9.252 - 250 mm10.110 mm
11.2360mm - Wheelbase
12.636 - 634 mm
13.488 - 482 mm
14.488 - 482 mm
15.3431,1 - 3426,1 mm
16.588,3 - 586,3 mm
17.2313,8 - 2311,8 mm
18.590,5 mm
19.295,25 mm
20.519,30 - 517,30 mm
21.259,80 - 258,50 mm
22.1242,6 - 1240,6 mm
23.642,5 - 639,5 mm24.750,9 mm
25.439,5 - 436,5 mm
26.136,5 mm
27.299,5 - 295,5 mm
28.103 - 100 mm
29.131,5 - 126,5 mm
30.705,5 - 704,5 mm
31.705,5 - 704,5 mm
32.42,2 - 40,2 mm
33.491 - 486 mm
34.594,2 - 593,4 mm
35.283,0 - 282,2 mm
36.32,25 - 31,25 mm
37.397 - 395 mm
Engine mounting dimensions - section V-V
Section V-V, Tdi and Td5 engine mounting bracket dimensions. The dimensions are applicable to all derivatives.
Tdidimensions:
A = 276.5
B = 553
C = 127.9
D = 317.4
E = 4 degreesTd5dimensions:
A = 273.2
B = 546.5
C = 187.8
D = 374.3
E = 4 degrees
ProCarManuals.com

PANEL REPAIRS
5
BODY DIMENSIONS LAND ROVER 110
ProCarManuals.com

77PANEL REPAIRS
6
BODY DIMENSIONS LAND ROVER 110
CHASSIS ALIGNMENT DIMENSIONS
A - Front Datum
B - Chassis Datum
C - Front axle centre line
D - Rear axle centre line
1.4148 - 4143 mm
2.4009,5 - 4005 mm
3.978,7 - 981,2 mm
4.22 - 20 mm
5.252 - 250 mm
6.239 - 236,5 mm
7.3023,3 - 3022,3 mm
8.3030,7 - 3028,7 mm
9.155 - 153 mm
10.871,2 - 869,2 mm
11.2794 mm - Wheelbase
12.488 - 482 mm13.488 - 482 mm
14.82 - 79,5 mm
15.750,9 mm
16.750,9 mm
17.440,5 - 435,5 mm
18.440,5 - 435,5 mm
19.299,5 - 295,5 mm
20.500 - 495 mm
21.500 - 495 mm
22.594,2 - 593,4 mm
23.594,2 - 593,4 mm
24.283 - 282,2 mm
25.283 - 282,2 mm
26.1970 - 1968 mm
27.642,9 - 639,5 mm
28.750,9 mm29.290,5 mm
30.295,5 mm
31.299,5 - 295,5 mm
32.103 - 100 mm
33.1177,5 - 1175,5 mm
34.1692,5 - 1689,5 mm
35.2610 - 2606 mm
36.2040,5 - 2037,5 mm
37.1912,5 - 1909,5 mm
38.1359 - 1357 mm
39.1573 - 1571 mm
40.270 - 268 mm
41.665,5 - 663,5 mm
42.440 - 438 mm
43.32,25 - 31,25 mm
Section V-V is through the engine mountings. Dimensional information for the mountings can be found in Land
Rover’90’engine mounting dimensions.
ProCarManuals.com

PANEL REPAIRS
7
BODY DIMENSIONS LAND ROVER 130
ProCarManuals.com

77PANEL REPAIRS
8
BODY DIMENSIONS LAND ROVER 130
CHASSIS ALIGNMENT DIMENSIONS
A - Front Datum
B - Chassis Datum
C - Front axle centre line
D - Rear axle centre line
E - Chassis Datum, section A - A
1.633,0 mm reference only
2.3569,3 - 3567,3 mm
3.2421,8 - 2419,8 mm
4.2317,5 - 2314,5 mm
5.2188,3 - 2185,3 mm
6.2119,5 - 2117,3 mm7.1990 - 1988 mm
8.1970 - 1968 mm
9.2401,8 - 2399,8 mm
10.110,0 mm reference
11.149,7 - 146,7 mm reference dimension
12.3225.8 mm - Wheelbase
NOTE: The above dimensions are for the Land Rover 130 chassis frame. For additional
measurements, refer to the Land Rover 110 chassis frame drawing and aligment dimensions.
ProCarManuals.com

PANEL REPAIRS
9
BODY DIMENSIONS GAP AND PROFILE INFORMATION
The following information is to be used as a guide to assist the technician in refitting exterior body panels and trim
items, to achieve a correctly aligned and cosmetically acceptable vehicle.
Section A-A, Bonnet to wing, gap A = 3 - 8 mm. To be parallel within 2 mm.
Section B-B, Wing to’A’post lower, gap B = 0. Profile = +/- 1 mm.
Section C-C, Wing to sill, gap C = 0. Profile = +/- 1 mm.
Section D-D, Screen aperture to door frame, gap D = 5 - 9 mm.
Section E-E, Door frame to roof, gap E = 7 - 11 mm.
Section F-F, Front and rear door to’B/C’post, gap F = 7 - 11 mm.
ProCarManuals.com

77PANEL REPAIRS
10
BODY DIMENSIONS
Section G-G, Door to sill, gap G = 7 - 11 mm. Door profile to sill = 0 to + 2 mm.
Section H-H, Rear door to body, gap H = 7 - 11 mm. Door profile to body = 0 to + 3 mm.
Section J-J, Body side lower to body, gap J = 0 - 4 mm. To be parallel within 2 mm.
ProCarManuals.com

PANEL REPAIRS
11
BODY DIMENSIONS
Section K-K, Roof to taildoor, gap K = 7 - 9 mm. Profile = +/- 1 mm.
Section L-L, N-N, Body side to taildoor, gap L = 5 - 7 mm. Profile = +/- 1 mm.
Section M-M, Body rear to taildoor, gap M = 7 - 9 mm.
ProCarManuals.com