fuse box LAND ROVER DEFENDER 1999 User Guide

76CHASSIS AND BODY
20
REPAIR
14.Carefully prise Land Rover decal from grab
handle.
15.Remove 2 screws securing grab handle to crash
pad and lower fascia panel.
16.Remove grab handle.
17.Remove 4 screws securing demister vents to
crash pad.
18.Remove both demister vents.
19.Remove 3 screws securing crash pad to
bulkhead.
20.Remove crash pad.
21.Release radio from fascia.
22.Disconnect 2 multiplugs and aerial from radio.23.Remove radio.
24.Remove 2 trim studs securing radio housing to
fascia.
25.Remove radio housing.
26.Remove auxilliary switch panel.See this
Section.
27.Remove auxilliary switch panel cover.
28.Remove interior fuse box cover.
ProCarManuals.com

76CHASSIS AND BODY
22
REPAIR
35.Remove 7 trim clips securing trim upper fascia
trim casing to bulkhead.
36.Carefully fold back trim casing over fresh air vent
operating levers and remove.
37.Release demist hose from parcel shelf.
38.Remove 18 screws securing parcel shelf to
lower fascia panel.
39.Remove parcel shelf.
40.Remove 7 screws securing bottom edge of lower
fascia panel to bulkhead.
41.Remove both retaining plates and lower footwell
covers.
42.Remove 2 bolts securing top of lower fascia to
bulkhead.
43.With assistance, remove lower fascia.Refit
44.With assistance, fit lower fascia.
45.Fit 2 bolts securing top of lower fascia to
bulkhead.
46.Fit both retaining plates and footwell covers to
lower fascia.
47.Fit 7 screws securing bottom edge of lower
fascia to bulkhead.
48.Fit parcel shelf to lower fascia and secure with
screws.
49.Fit demist hose to parcel shelf.
50.Carefully manoeuvre upper fascia trim casing
over fresh air vents and fit to fascia.
51.Fit trim clips securing trim casing to bulkhead.
52.Fit finisher rail to lower fascia and secure with
screws.
53.Fit wiper motor cover and secure with screws.
54.Fit both door check strap covers and secure with
screws.
55.Fit both footwell vents to lower fascia and secure
with screws.
56.Fit interior fuse box cover.
57.Fit auxilliary switch panel cover.
58.Fit auxilliary switch panel.See this Section.
ProCarManuals.com

84WIPERS AND WASHERS
4
DESCRIPTION AND OPERATION REAR WIPER - FROM 02MY
1.Rear wiper relay
The rear wiper system is unchanged except for the addition of a wiper motor relay into the electrical circuit.
The new rear wiper relay is located in the tail door, below the wiper motor. The relay coil is energised by a feed
supplied from the rear wiper switch. When the relay contacts close, a feed is supplied via the ignition switch
(position II) and a fuse in the passenger compartment fuse box, through the relay contacts to the wiper motor.
ProCarManuals.com

86 - ELECTRICAL
CONTENTS
Page
DESCRIPTION AND OPERATION
SECURITY AND CENTRAL DOOR LOCKING 1....................................................
SECURITY AND CENTRAL DOOR LOCKING 2....................................................
ANTI-THEFT ALARM - FROM 02MY 3...................................................................
IMMOBILISATION SYSTEM - FROM 02MY 12......................................................
CENTRAL DOOR LOCKING (CDL) - FROM 02MY 15...........................................
ANTI-THEFT ALARM SYSTEM SELF TEST 17.....................................................
FASCIA CONSOLE 18............................................................................................
HEATED FRONT SCREEN - FROM 02MY 20.......................................................
HEATED FRONT SEATS - FROM 02MY 22..........................................................
ELECTRIC FRONT WINDOWS - FROM 02MY 24.................................................
PASSENGER COMPARTMENT FUSE BOX 26.....................................................
UNDER SEAT FUSE BOX 27.................................................................................
ADJUSTMENT
HEADLAMPS - ALIGN BEAM 1..............................................................................
SOLENOID/MOTOR - FRONT DOOR - ADJUST 1................................................
REPAIR
BELT - AUXILLARY DRIVE 1.................................................................................
HARNESS - INJECTORS 1....................................................................................
STARTER MOTOR 2..............................................................................................
CENTRE HIGH MOUNTED STOP LIGHT (CHMSL) - UP TO 02MY 2...................
ALTERNATOR 3.....................................................................................................
HORN - LH 4...........................................................................................................
HEADLAMP 5.........................................................................................................
LAMP - TAIL 6.........................................................................................................
RADIO6 ..................................................................................................................
SPEAKER - FRONT 7.............................................................................................
SWITCH - TRANSMISSION BRAKE 7...................................................................
LAMP - FRONT FLASHER 8..................................................................................
BATTERY - DISCONNECT - FROM 02MY 8..........................................................
MOTOR & REGULATOR - FRONT DOOR - FROM 02MY 9..................................
SWITCH - FASCIA - FROM 02MY 10.....................................................................
HARNESS - FRONT DOOR - FROM 02MY 10.......................................................
SOLENOID/MOTOR - TAIL DOOR - FROM 02MY 11............................................
SOLENOID/MOTOR - FRONT DOOR - FROM 02MY 12.......................................
SOLENOID/MOTOR - REAR DOOR - FROM 02MY 13.........................................
HARNESS - REAR DOOR - FROM 02MY 14.........................................................
REVERSE AND FOG GUARD LAMP - BULB 15....................................................
ProCarManuals.com

ELECTRICAL
3
DESCRIPTION AND OPERATION ANTI-THEFT ALARM - FROM 02MY
The alarm and immobilisation system on 2002MY Defender is similar to that used on Discovery Series I (LJ)
models from 1996MY. The alarm system comprises the anti-theft alarm ECU, bonnet and door switches and a
volumetric sensor.
Anti-Theft Alarm ECU
The anti-theft alarm ECU is located behind the instrument pack and receives a permanent battery supply via fuses
6 and 7 in the under seat fuse box. The ECU also receives a battery supply via the ignition switch position II and
fuse 1 in the passenger compartment fuse box. The ECU is connected to the various supporting components by
two harness connectors.
The ECU controls the alarm system (perimetric and volumetric security), CDL system, engine immobilisation
system (Td5 only) and various other vehicle functions including direction indicators and interior lamps.
The anti-theft alarm ECU incorporates an RF receiver and antenna for reception of RF signals from the remote
handset for locking and alarm arming. The antenna is unterminated at one end, and for optimum performance the
antenna must not be wound around adjoining harnesses.
The anti-theft alarm ECU operates at one of two frequencies which are identified by a label on the unit. The
frequencies are:
433 MHz - Europe, Gulf States, South Africa
315 MHz - North America, South East Asia, Japan, Australia.
The anti-theft alarm ECU also incorporates an integral inertia switch. In the event of an impact of sufficient severity
to trigger the inertia switch when the ignition is on, the ECU will unlock all doors and operate the hazard warning
lamps. The ECU will remain in this condition for a pre-programmed period of 2 minutes. To reinstate CDL
functionality and to deactivate the hazard warning lamps, the ignition should be turned off and then on after the 2
minute timer has expired.
NOTE: There is a separate inertia switch for fuel cut off.
ProCarManuals.com

ELECTRICAL
7
DESCRIPTION AND OPERATION Alarm Sounders
1.Battery Backed Up Sounder (BBUS)
2.Alarm sounder
Two types of alarm sounder are available, dependant on the vehicle market configuration.
A Battery Backed-Up Sounder (BBUS) is used in some markets and located in the LH front wing, behind the
headlamp. This is a tamper proof sounder with its own power supply which allows it to continue operating even if
disconnected from the vehicle power supply. The BBUS is connected to a permanent battery supply via fuse 7 in
the under seat fuse box. Two further connections are made to the anti-theft alarm ECU and a fourth connection is
to an earth header. If the BBUS is disconnected without first being disarmed by the anti-theft alarm ECU, it will
operate for 4.5 minutes.
To disarm the BBUS, when the battery is to be disconnected for instance, the ignition must be turned on to
position II and back to the off position , after which a 17 second delay is initiated to allow the battery or BBUS
connector to be disconnected. If the BBUS sounds, it can be disarmed by unlocking the vehicle with the remote
handset.
Where a BBUS is not specified, a standard vehicle horn is used for the alarm sounder and is located in the LH
front wing, behind the headlamp. The sounder is operated by an alarm relay which is controlled by the anti-theft
alarm ECU. The relay receives a permanent battery supply via fusible link 6 in the under seat fuse box. The relay
coil is connected to the anti-theft alarm ECU which provides an earth for the coil when horn operation is required.
This operates the relay contacts and supplies battery voltage to the sounder, causing it to operate.
ProCarManuals.com

ELECTRICAL
9
DESCRIPTION AND OPERATION Security LED
The security LED has a number of functions to indicate anti-theft alarm system status. The LED is located in the
speedometer housing in the instrument pack. The LED receives a permanent battery supply via fusible link 6 in
the under seat fuse box. The LED is connected to the anti-theft alarm ECU which earths the connection when LED
operation is required. When the LED is not required to be illuminated, the anti-theft alarm ECU holds the
connection at battery voltage, keeping the LED extinguished.
When the system is armed and the bonnet and all doors are closed, the LED flashes quickly for a 10 second
confirmation period and confirms that perimetric and volumetric systems are armed. After the 10 second
confirmation period the LED flash changes to a slow flash to confirm that the alarm and immobiliser systems are
armed and to act as deterrent to thieves.
The LED also conveys CDL system information and this functionality is described in the Central Door Locking
(CDL) section.
ProCarManuals.com

86ELECTRICAL
12
DESCRIPTION AND OPERATION IMMOBILISATION SYSTEM - FROM 02MY
Engine immobilisation is available on all 2002MY engine derivatives, although it is not available in selected
markets. On Td5 models, the immobilisation system is controlled directly by the anti-theft alarm ECU. On 300Tdi
models, the immobilisation system is controlled by an engine immobilisation ECU in conjunction with the anti-theft
alarm ECU.
When immobilisation occurs on Td5 models, engine crank is disabled by the anti-theft alarm ECU breaking the
earth path for the starter relay coil and the ECM disables the fuel pump relay and the glow plug relay.
When immobilisation occurs on 300Tdi models, engine crank is disabled by the anti-theft alarm ECU breaking the
earth path for the starter relay coil and the engine immobilisation ECU disables the fuel cut-off solenoid, the starter
motor solenoid and the glow plug relay.
Two types of immobilisation are available; passive and active.
Engine Immobilised Warning Lamp
The engine immobilised warning lamp is located in the instrument pack. The lamp is used by the anti-theft alarm
ECU to show that the engine is immobilised during an attempted engine start.
The warning lamp receives a battery supply from the ignition switch position I (aux) via the passenger
compartment fusebox. The anti-theft alarm ECU controls the warning lamp. When the warning lamp is not
required, the ECU supplies a battery supply to the warning lamp. When warning lamp operation is required, the
ECU provides an earth for the bulb.
If the ignition switch is moved to the crank position, but operation of the starter motor is prohibited and the engine
immobilised warning lamp flashes, then the anti-theft alarm ECU has not received the correct code from the
remote handset and the vehicle will remain immobilised. Ensure that the remote handset is in the proximity of the
transponder coil. If the remote handset is not available or inoperative, the immobilisation system can be disarmed
using the EKA procedure outlined later in this section.
If the ignition switch is turned to the crank position III and the remote handset is not in the proximity of the
transponder coil, engine immobilisation will remain active and the warning lamp will flash to inform the driver.
ProCarManuals.com

ELECTRICAL
15
DESCRIPTION AND OPERATION CENTRAL DOOR LOCKING (CDL) - FROM 02MY
The Central Door Locking (CDL) system is a new feature for 2002MY Defender.
NOTE: CDL operates all doors on Station Wagon and County Station Wagons. On all other
Defender 2002MY variants, CDL operates on the driver and front and rear passenger doors only.
General
CDL operates on all doors, including the tail door and is operated by pressing the appropriate button on the
remote handset, using the vehicle key in the drivers door lock or using the drivers door sill button.
The CDL system introduces electrically operated door latches which are controlled by the anti-theft alarm ECU,
located behind the instrument pack. The anti-theft ECU receives a permanent power supply from fuse 6 in the
passenger compartment fuse box. Each CDL latch motor is connected by two wires to the anti-theft ECU which
alternately supplies power and earth connections to drive each motor to the lock or unlock positions.
If the latch motors are continually operated in a short period of time, the anti-theft ECU will suspend all CDL latch
motor operation for 15 seconds to prevent the motors from overheating. Before suspension occurs the anti-theft
ECU ensures that all the doors are left in the unlocked condition.
If the vehicle is locked, and the key is in the ignition switch or the ignition is on and the anti-theft alarm ECU inertia
switch is tripped, all doors will be unlocked immediately and the hazard warning lamps will operate. To prevent
accidental relocking, all latch motors will be inhibited until the anti-theft ECU senses that the drivers door is
opened with the key removed from the ignition switch.
Locking of the vehicle using the remote handset is inhibited with the key in the ignition switch.
Slam Locking
With the introduction of CDL, slam locking of the drivers door is disabled. If an attempt is made to slam lock the
vehicle, the anti-theft alarm ECU will unlock all doors.
CDL Using the Drivers Door Sill Button
Each door has a sill button to allow that door to be individually locked from inside the vehicle. The drivers door sill
button has additional functionality which allows all doors to be locked from inside the vehicle from this one button.
When the driver door sill lock button is depressed, the CDL system enters a sill locked state, where all doors are
locked but immobilisation and perimetric and volumetric sensing is suspended. CDL using the drivers sill lock
button can be achieved with or without the key in the ignition switch and without the ignition being on.
If the CDL is in the sill locked state and the lock button on the remote handset is pressed, the volumetric and
perimetric functions of the alarm system will become active and active engine immobilisation will be invoked.
ProCarManuals.com

86ELECTRICAL
20
DESCRIPTION AND OPERATION HEATED FRONT SCREEN - FROM 02MY
1.Heated front screen RH connector
2.Heated front screen LH connector
3.Heated front screen ECU (behind instrument pack)
4.Heated front screen relay (passenger compartment fuse box)
5.Heated front screen switch
ProCarManuals.com