oil filter LAND ROVER DEFENDER 1999 User Guide

12ENGINE
18
DESCRIPTION AND OPERATION Oil filters
The Td5 engine features two types of oil filter; the main filter is a standard disposable cartridge-type full flow oil
filter which is augmented with a by-pass centrifuge filter used to filter out particulate matter having a smaller
diameter smaller than 15 micron but greater than 3 micron.
1.Centre spindle
2.Spindle oil holes (2 off)
3.Centrifuge filter housing
4.Centrifuge filter drain pipe
5.Port - centrifuge filter drain pipe to sump6.Filter rotor
7.Internal seal
8.Cover
9.Cover screws (2 off)
The centrifuge filter is located on the left hand side of the engine block by the exhaust manifold and is housed in a
pot which is bolted to the oil cooler housing by means of three bolts. The pot contains a rotor located on a central
spindle which spins at up to 15,000 rev/min when oil is flowing through the unit under pressure. The rotor contains
two fine holes drilled at obtuse angles which cause the rotor to spin about the centre spindle when high pressure
oil is passing through it. The inner surface of the rotor captures carbon deposits and small particulate matter as it
is thrown outwards under centrifugal force to form a sludge on the inner walls of the rotor. The unit is able to trap
very fine impurities that build up in the oil that would be too small to filter using the normal paper-element type
full-flow filters alone.
ProCarManuals.com

ENGINE
19
DESCRIPTION AND OPERATION Full flow filter
Approximately 10% of the total oil flow enters the centrifuge pot through a side port in the pot casting which is
mated to an outlet port at the lower side of the oil cooler housing. A rubber’O’ring sits in a recess around the oil
cooler port which seals the faces between the centrifuge pot and oil cooler port, and it must be replaced every
time the centrifuge assembly is removed. Oil leaves the centrifuge pot through a drain tube which is attached to
the base of the pot by means of two fixing screws. The lower end of the drain tube returns oil to the sump and is
fixed to the sump by means of two screws. Gaskets are included at the port interfaces between the oil drain tube
and the centrifuge pot and the oil drain tube and sump return port; these gaskets must be replaced every time the
oil drain tube is removed.
The centrifuge cover is fixed to the pot by two screws and is sealed by an’O’ring.
1.Full-flow filter housing
2.Thermostat
3.Roll-pin4.Port - feed line to turbocharger
5.Outlet port from full-flow filter - higher than 74°C
6.Inlet port to full-flow filter
7.Outlet port from full-flow filter - lower than 74°C
The main filter is a conventional full flow cartridge type filter containing a paper element able to trap particles
greater than 15 micron (0.015 mm) in diameter.
The cartridge is screwed to an adaptor casting by way of a hollow brass threaded insert which connects the filter
outlet port to the adaptor casting. A sealing ring seals the union between the oil filter cartridge and the adaptor
casting.
ProCarManuals.com

12ENGINE
20
DESCRIPTION AND OPERATION Oil filter housing thermostat
1.Circlip
2.Thermostat end cap
3.Oil seal
4.Thermostatic valve5.Return spring
6.Oil filter housing
7.Threaded insert
The oil filter housing contains a thermostatically controlled valve to control the direction and proportion of oil flow
through the oil cooler matrix. When the oil temperature is cool, the centre spindle of the thermostatic element is
compressed. In this condition the valve completely seals the passage to the turbocharger feed tapping and flow is
directed through the oil filter adaptor housing, passing from the outlet of the full-flow filter to the cylinder block via
the rear oil return gallery in the oil cooler housing. A proportion of the oil flow from the right hand filter outlet port is
passed through to the oil cooler matrix to supply the turbocharger oil feed line.
When the oil temperature rises, the heated wax in the thermostat causes the thermostat centre spindle to rise and
push against the housing end cap, compressing the valve spring further and so opening the valve. In this
condition, oil flow from the outlet side of the full-flow filter is allowed to pass directly to the turbocharger oil feed
line and reverses the flow through the oil cooler matrix, which now delivers a proportion of cooled oil flow to the
cylinder block via the outlet port at the right hand side of the oil cooler housing.
The filter canister contains a by-pass valve which opens when the engine is cold or if the filter becomes blocked.
The by-pass valve opens when a pressure drop of greater than 1.6 kg/cm
2(157 kPa, 23 lbf/in2) is experienced.
ProCarManuals.com

12ENGINE
22
DESCRIPTION AND OPERATION CRANKSHAFT, SUMP AND OIL PUMP
The crankshaft, sump and oil pump components are described below:
Sump
The sump is a wet-type, of aluminium construction and is sealed to the engine block by means of a rubber gasket
and twenty fixing bolts. The four bolts at the gearbox end of the sump are longer than the other sixteen bolts.
The sump gasket incorporates compression limiters (integrated metal sleeves) at the bolt holes, which are
included to prevent distortion of the gasket when the sump to cylinder block bolts are being tightened.
An oil drain plug is fitted at the bottom of the oil sump reservoir. An oil return drain pipe is also attached to the oil
sump which returns oil from the centrifugal filter.
Stiffener Plate
The stiffener plate assembly provides lower engine block rigidity and utilises dowels to align it to the bottom of the
cylinder block. A rotary oil pump is integral with the stiffener plate and an oil pick-up and strainer assembly is fitted
to the underside of the stiffener plate. The stiffener and oil pump assembly is secured to the cylinder block by 22
bolts.
ProCarManuals.com

ENGINE
33
DESCRIPTION AND OPERATION 1.Oil squirt jets (5 off)
2.Main oil delivery gallery
3.Inflow from oil cooler housing
4.Flow to oil cooler / filters (from oil pump via cylinder block)
5.Sump
6.Oil pick-up pipe
7.Flow from oil pump (relief-valve in housing)
8.Oil pump
9.Cross-drilling supply to main and crankshaft bearings
10.To cylinder head
Oil from the sump is drawn up through a two-piece plastic pick-up which contains a mesh to siphon any relatively
large pieces of material which could cause damage to the pump. The head of the pick-up is centrally immersed in
the sump oil and oil is delivered to the inlet side of the eccentric rotor pump through a gallery in the stiffener plate.
Pressurised oil from the pump is passed through to the cylinder block where it is delivered to the centrifuge filter
and full-flow filter via a port in the RH cylinder block which interfaces with a port in the centre gallery of the oil
cooler housing. The oil pump contains an oil pressure relief valve which opens to allow oil to be recirculated back
around the pump if the oil pressure increases to a high enough level.
10% of the oil flow from the pump is diverted through the centrifuge filter and returned to the sump via the
centrifuge filter drain tube. The remaining 90% of the oil passes through the standard full-flow filter to the main oil
gallery in the cylinder block.
ProCarManuals.com

12ENGINE
34
DESCRIPTION AND OPERATION OIL COOLER / FILTER FLOW
(THERMOSTAT OPEN)
ProCarManuals.com

ENGINE
35
DESCRIPTION AND OPERATION 1.To cylinder block main gallery (from rear of oil cooler housing)
2.Oil cooler housing
3.Oil pressure switch
4.Full-flow filter
5.Centrifuge filter
6.Return to sump
7.Flow from oil pump (via cylinder block)
8.Oil cooler matrix
When the engine temperature is below 74°C, the thermostat in the full-flow filter adaptor housing is closed and a
proportion of the oil flow to the main oil gallery is diverted to the oil cooler to supply an oil feed to the turbocharger
bearings. Oil passes through the oil cooler to the front gallery in the oil cooler housing where there is a tapping to
connect the feed pipe to the turbocharger. Oil used by the turbocharger bearings is returned to the sump through
an oil drain pipe which connects to a port in the LH side of the cylinder block.
The remainder of the oil flow leaving the full-flow filter outlet is passed into the cylinder block via a port at the rear
of oil cooler rear gallery.
When the oil temperature rises above 74°C the thermostat in the full-flow filter housing begins to open to allow a
proportion of the oil from the full-flow filter to pass through the oil cooler before it reaches the main oil gallery in the
cylinder block. In this instance, oil supply to the turbocharger bearings is fed directly from the full-flow filter without
first passing through the oil cooler. Between 74°C and 88°C the thermostat valve plunger opens by about 9 mm
(0.3 in) to allow proportionally more oil to flow through the oil cooler before being passed to the cylinder block main
oil delivery gallery. Above 88°C the thermostat valve continues to open by about 1mm (0.03 in) for every 10°C
increase in temperature until the valve is fully open, when all the oil flow to the cylinder block is forced to pass to
the cylinder block via the oil cooler.
An oil pressure switch is located in a port in the rear gallery of the oil cooler housing to sense the oil pressure level
before flow enters the main oil gallery in the engine block. A warning lamp in the instrument cluster is switched on
if the oil pressure is detected as being too low.
Drillings from the cylinder block main oil gallery direct oil to the crankshaft main bearings and cross drillings in the
crankshaft direct oil to the big-end bearings. An additional five drillings in the cylinder block supply oil at reduced
pressure to the oil squirt jets for piston cooling and gudgeon pin lubrication.
Oil supply from the cylinder block is then passed to the cylinder head galleries through a non-return valve which is
included as an integral item in the lower face of the cylinder head.
ProCarManuals.com

12ENGINE
6
REPAIR GASKET - CYLINDER HEAD
Service repair no - 12.29.02
Remove
NOTE: The following procedures cover
engines fitted with or without an EGR
cooler. The EGR cooler is bolted to the
front of the cylinder head.
1.Remove underbelly panel.See CHASSIS AND
BODY, Repair.
2.Drain cooling system.See COOLING
SYSTEM, Adjustment.
3.Remove camshaft cover gasket.See this
Section.
4.Remove cooling fan.See COOLING SYSTEM,
Repair.
5.Release clips and disconnect air flow meter from
air filter.
6.Disconnect multiplug from air flow meter.
7.Loosen clip and remove air inlet hose from
turbocharger.
8.Remove 3 bolts and remove exhaust manifold
heat shield.
9.Remove turbocharger oil feed banjo bolt and
discard sealing washers.
10.Remove 3 nuts, release turbocharger from
exhaust manifold, discard gasket and tie
turbocharger aside.
11.Remove 2 bolts securing engine harness to
camshaft carrier.
12.Disconnect fuel injector, coolant and compressor
sensors.
13.Disconnect 4 heater plug connectors.
ProCarManuals.com

12ENGINE
14
REPAIR
9. Not EU3 model:-Apply two 3 mm diameter
beads of sealant, Part No.STC 5433 to areas’A’
shown on illustration.
CAUTION: Excessive use of sealant could
result in blockage of oil drain hole,
arrowed’B’in illustration.
10.Fit new gasket to camshaft cover. fit cover and
tighten bolts to10 Nm (7 lbf.ft).
11.Position breather hose and secure clip.
12.Fit engine acoustic cover.
13.Reconnect battery negative lead.
14.Fit battery cover.ENGINE AND ANCILLARIES
Service repair no - 12.41.01.99
Remove
1.Remove underbelly panel.See CHASSIS AND
BODY, Repair.
2.Drain engine oil.
3.Remove radiator.See COOLING SYSTEM,
Repair.
4.Remove turbocharger.See FUEL SYSTEM,
Repair.
5.Remove starter motor.See ELECTRICAL,
Repair.
6.Remove air filter.See FUEL SYSTEM, Repair.
7.Loosen clip screw and release air intake hose
from intake elbow.
8.Release clips and disconnect coolant hoses
from fuel cooler and coolant rail.
ProCarManuals.com

ENGINE
19
REPAIR 70.Connect coolant hoses to fuel cooler and coolant
rail and secure clips.
71.Fit air intake hose to intake elbow and tighten
clip screw.
72.Fit starter motor.See ELECTRICAL, Repair.
73.Fit turbocharger.See FUEL SYSTEM, Repair.
74.Fit radiator.See COOLING SYSTEM, Repair.
75.Fit air filter.See FUEL SYSTEM, Repair.
76.Fill engine with oil.
77.Fit underbelly panel.See CHASSIS AND
BODY, Repair.MOUNTING - FRONT - LH
Service repair no - 12.45.01
Remove
1.Remove centrifuge assembly.See this
Section.
2.Remove 3 bolts, remove oil filter adaptor
housing and discard gasket.
3.Fit suitable lifting chains to support engine.
4.Remove 2 nuts securing engine mounting to
chassis.
5.Remove 4 bolts securing engine mounting
bracket to cylinder block.
6.Remove nut securing mounting to mounting
bracket.
7.Remove mounting and mounting bracket.
8.Remove mounting shield.
ProCarManuals.com