heater LAND ROVER DEFENDER 1999 Owner's Manual

37MANUAL GEARBOX
8
REPAIR
12.Remove 13 screws securing tunnel cover.
13.Release and remove tunnel cover.
14.Remove cooling fan.See COOLING SYSTEM,
Repair.
15.Remove air filter.See FUEL SYSTEM, Repair.
16.Remove 2 upper bolts securing clutch housing to
engine.
17.Remove bolt securing shim to clutch housing.
18.Release gearbox breather pipes from clips on
heater hose.
19.Remove starter motor.See ELECTRICAL,
Repair.
20.Remove exhaust front pipe.See MANIFOLD
AND EXHAUST SYSTEM, Repair.
21.Drain gearbox oil.See Adjustment.
22.Drain transfer gearbox oil.See
MAINTENANCE ,
23.Remove 3 nuts securing intermediate silencer to
tail pipe.
24.Release silencer from mounting rubbers, remove
silencer and discard gasket.
25.Mark front and rear propeller shaft to transfer
gearbox flanges for reassembly purposes.
ProCarManuals.com

MANUAL GEARBOX
11
REPAIR Refit
44.Clean gearbox to engine mating faces, dowels
and dowel holes.
45.With assistance raise gearbox on jack and align
to clutch and engine.
46.Fit lower bolts securing clutch housing to engine
and tighten to50 Nm (37 lbf.ft).
NOTE: Do not fit upper bolts at this stage.
47.Fit earth leads and secure with bolt.
48.Connect Lucars to differential lock switch,
multiplug to reverse light switch, position
multiplug to bracket and connect low ratio detect
multiplug - if fitted.
49.Raise gearbox jack and guide transfer gearbox
lever through tunnel.
50.Secure body harness clips to bracket on top of
transfer gearbox.
51.Position battery earth lead to transfer gearbox
and tighten retaining nut.
52.Connect multiplug to speed sensor and secure
harness in clip on transfer gearbox.
53.Position mounting brackets and rubber
mountings, positioning heat shield to LH
mounting and tighten bracket bolts to85 Nm (63
lbf.ft).
54.Position nuts to mountings and tighten to48 Nm
(35 lbf.ft).
55.Remove 3 bolts securing support plate
LRT-99-007to gearbox.
56.Position handbrake cable through heel board.
57.Position clutch slave cylinder, fit bolts and
tighten to25 Nm (18 lbf.ft).
58.Clean propeller shafts and mating faces.
59.Position propeller shafts, align to marks and
tighten nuts to48 Nm (35 lbf.ft).
60.Clean intermediate silencer and tail pipe mating
faces.
61.Position silencer and secure on mountings,
using a new gasket align to tail pipe, fit nuts and
tighten to25 Nm (18 lbf.ft).
62.Refill gearbox with oil.See Adjustment.
63.Refill transfer gearbox with oil.See
MAINTENANCE ,
64.Fit exhaust front pipe.See MANIFOLD AND
EXHAUST SYSTEM, Repair.
65.Refit starter motor.See ELECTRICAL, Repair.
66.Fit bolt securing shim plate to clutch housing and
tighten10 Nm (7 lbf.ft).
67.Position heater pipe to gearbox housing, fit
upper bolts securing clutch housing to engine
and tighten to50 Nm (37 lbf.ft).
68.Position gearbox breather pipes to clips on
heater hose.69.Fit air cleaner.See FUEL SYSTEM, Repair.
70.Fit cooling fan.See COOLING SYSTEM,
Repair.
71.Fit and align tunnel cover, fit and tighten screws.
72.Position relay panel, fit spacers and tighten
screws.
73.Position hand-brake lever and tighten bolts to25
Nm (18 lbf.ft).
74.Connect handbrake cable to lever, fit clevis pin,
washer and new split pin.
75.Connect Lucar to hand-brake switch.
76.Position gaiter to handbrake lever and secure
with trim stud.
77.Locate insulation pad over gear levers and fit to
tunnel cover.
78.Align spline marks, fit gear lever to lower lever,
fit washer and secure with retaining nut.
79.Position gear lever cover.
80.Position gearbox tunnel carpet.
81.Fit gear lever and transfer gear lever knobs.
82.Reconnect battery negative lead.
83.Fit battery cover.
ProCarManuals.com

76CHASSIS AND BODY
4
REPAIR WING - FRONT
Service repair no - 76.10.24
Remove
1.Remove wheel arch liner.See this Section.
2.Remove front grille.See this Section.
3.Release fixings and remove cooling fan cowl.
4.Remove air cleaner grille from front wing.
5.Remove 4 screws securing air intake elbow to
wing.
6.Remove 7 screws and remove heater air intake
grille from wing.
7.Remove 2 bolts securing heater air intake
bracket to inner wing. Remove bracket.
8.Remove heater air intake from wing and collect
seal.
9.Remove 2 bolts securing EGR solenoid to inner
wing and lay aside.
10.Remove 3 studs securing expansion tank pipe to
inner wing.
11.Remove 2 bolts securing PAS reservoir to inner
wing and lay aside.
12.Remove 4 bolts securing outer wing to inner
wing.
ProCarManuals.com

CHASSIS AND BODY
7
REPAIR Refit
29.Fit bonnet cable grommet.
30.Fit side repeater lamp to wing.
31.Fit headlamp sealing ring, fit headlamp and
tighten screws.
32.Fit headlamp finisher, side and indicator lamps
and tighten screws.
33.Fit grille support bracket and tighten bolt.
34.With assistance, position and align wing to body
and locate bonnet cable to wing.
35.Connect headlamp, indicator, side lamp and side
repeater lamp multiplugs.
36.Fit bolt securing wing to bulkhead.
37.Fit bolts securing wing to’A’post.
38.Fit nut and bolt securing support stay to wing.
39.Fit bolt securing inner and outer wing to chassis.
40.Fit bolts securing radiator bracket to wing.
41.Fit bolts securing outer wing to inner wing.
42.Align wing and finally tighten all bolts.
43.Position wheel arch extension to wing, and fit
securing studs.
44.Position PAS reservoir to wing and tighten bolts.
45.Position expansion tank pipe and secure with
studs.
46.Position EGR solenoid and tighten bolts.
47.Position heater air intake seal and fit air intake.
48.Fit heater air intake bracket and tighten bolts.
49.Fit heater air intake grille and tighten screws.
50.Align air cleaner intake elbow, tighten screws
and fit grille.
51.Fit wheel arch liner.See this Section.
52.Position bonnet release cable to lock and tighten
screw.
53.Fit cooling fan cowl.
54.Fit front grille.See this Section.STEP - FOLDING - REAR DOOR
Service repair no - 76.10.41
Remove
1.Remove 2 bolts securing step to chassis
member, remove step and collect spacers.
Refit
2.Position step, fit spacer washers and tighten
bolts.
ProCarManuals.com

CHASSIS AND BODY
19
REPAIR LOWER FASCIA PANEL - UP TO 02MY
Service repair no - 76.46.05
Remove
1.Disconnect battery negative lead.
2.Remove steering wheel.See STEERING,
Repair.
3.Remove 7 screws securing nacelle to steering
column.
4.Remove 2 halves of nacelle from steering
column.
5.Remove instrument pack.See ELECTRICAL,
Repair.
6.Remove 3 screws securing heater control cable
assembly to end of fascia.
7.Release heater control cable assembly from
fascia and move aside.
8.Release HRW, Rear Fog Guard Lamp, and
Hazard Warning switches from fascia.
9.Disconnect multiplugs and Lucars from switches.
10.Collect switches.
11.Remove locking rings from both front speakers.
12.Remove 4 screws securing each speaker to
fascia.
13.Disconnect multiplugs from speakers and
remove both front speakers.
ProCarManuals.com

CHASSIS AND BODY
23
REPAIR 59.Fit radio housing to fascia and secure with trim
studs.
60.Position radio to fascia and connect multiplugs
and aerial.
61.Fit radio to fascia.
62.Fit crash pad to fascia and secure with screws.
63.Fit both demister vents to crash pad and secure
with screws.
64.Fit grab handle to fascia and secure with screws.
65.Fit Land Rover decal to grab handle.
66.Position both front speakers to fascia and
connect multiplugs.
67.Fit speakers to fascia and secure with screws.
68.Fit locking rings to speakers.
69.Connect multiplugs and Lucars to HRW, Rear
Fog Guard Lamp, and Hazard Warning
Switches.
70.Fit switches to fascia.
71.Position heater controls to fascia and secure
with screws.
72.Fit instrument pack.See ELECTRICAL,
Repair.
73.Fit 2 halves of nacelle to steering column and
secure with screws.
74.Fit steering wheel.See STEERING, Repair.
75.Reconnect battery negative lead.PANEL - MOUNTING - FRONT DOOR - FROM 02MY
Service repair no - 76.11.28
Remove
1.Remove plastic sheet.See this Section.
2.Lower glass and remove 2 bolts securing door
glass to regulator.
3.Release glass from regulator, raise and wedge
in raised position.
ProCarManuals.com

CHASSIS AND BODY
27
REPAIR FACIA CONSOLE - FROM 02MY
Service repair no - 76.25.03
Remove
1.Disconnect battery earth lead.See
ELECTRICAL, Repair.
2.Remove radio.See ELECTRICAL, Repair.
3.Remove 4 screws securing instrument pack and
release pack from fascia.
4.Disconnect 2 multiplugs from warning lamp
panel.
5.Disconnect instrument pack multiplug from main
harness.
6.Remove instrument pack.
7.Remove 3 screws securing heater control and
release control from fascia.
8.Carefully prise Land Rover decal from grab
handle.
9.Remove 2 screws securing grab handle and
remove handle.
10.Remove 4 screws and remove demister vents.
ProCarManuals.com

CHASSIS AND BODY
29
REPAIR 25.Position console and connect Lucar and
multiplug to cigar lighter.
26.Connect multiplugs to remaining switches.
27.Fit console and secure with screws.
28.Fit crash pad and secure with screws.
29.Fit demister vents and secure with screws.
30.Fit grab handle, secure with screws and fit Land
Rover decal.
31.Fit heater control to fascia and secure with
screws.
32.Position instrument pack and connect multiplugs.
33.Fit instrument pack to fascia and secure with
screws.
34.Fit radio.See ELECTRICAL, Repair.
35.Connect battery earth lead.See ELECTRICAL,
Repair.GLASS - REAR DOOR - FROM 02MY
Service repair no - 76.31.02
Remove
1.Remove rear door mounting panel.See this
Section.
2.Loosen 2 nuts and remove door check strap
torsion bar and plate.
3.Remove check strap.
4.Remove inner and outer waist seal.
5.Remove screw from each glass channel.
6.Lower glass to bottom of door, lift over lower
edge and withdraw from door.
ProCarManuals.com

CHASSIS AND BODY
37
REPAIR
11.Remove 2 screws securing fuse cover and
remove cover.
12.Remove 7 screws securing lower edge of fascia
panel.
13.Remove footwell cover retaining plates.
14.Remove 2 nuts and remove lower fascia panel.
NOTE: Do not carry out further
dismantling if component is removed for
access only.
15.Remove 21 screws and release air duct cover.
16.Loosen trunnion screw, remove air distribution
cable and duct cover.Refit
17.Fit air distribution cable to duct cover and fit
inner cable to vent flap trunnion.
18.Tighten vent flap trunnion screw to6Nm(4
lbf.ft)and bend cable end to secure.
19.Fit duct cover to lower fascia and fit and tighten
screws.
20.Check condition of seal between heater and
lower fascia, if damaged replace.
21.Carefully fit lower fascia panel and ensure
harness route is correct.
22.Secure lower fascia panel with screws and
tighten nuts to10 Nm (7 lbf.ft).
23.Fit fuse cover and secure with screws.
24.Connect demister tubes to lower fascia panel.
25.Raise air distribution lever to screen demist
position and close footwell vent.
26.Connect air distribution cable to lever, tighten
grub screw and outer cable clamp.
27.Fit end cap to fascia and secure with screws.
28.Fit check strap covers and secure with screws.
29.Fit speakers.See ELECTRICAL, Repair.
30.Fit fascia closing panel.
31.Fit nut plate and fit screws to secure nut plate
and closing panel.
32.Fit knobs to air vent control levers.
33.Fit fascia console.See this Section.
34.Fit steering column nacelle.See STEERING,
Repair.
35.Connect battery negative lead.See
ELECTRICAL, Repair.
ProCarManuals.com

77PANEL REPAIRS
2
REPAIR WING UPPER - LH
Remove
1.Disconnect both battery leads, negative lead
first.
2.Remove headlamp.See ELECTRICAL,
Repair.
3.Remove headlamp mounting panel.See this
Section.
4.Remove radiator.See COOLING SYSTEM,
Repair.
5.Recover refrigerant from A/C system.See AIR
CONDITIONING, Repair.
6.Remove receiver drier.See AIR
CONDITIONING, Repair.
7.Remove relevant A/C pipes.
8.Remove relevant heater intake pipes.
9.Remove screen washer bottle.
10.Remove wheel arch liner.See CHASSIS AND
BODY, Repair.
11.Remove bolts and release welds securing panel,
remove panel.
Refit
12.Prepare and clean panel joint faces.
13.Reverse removal procedure.
14.Align headlamps.See ELECTRICAL,
Adjustment.WING UPPER - RH
Remove
1.Disconnect both battery leads, negative lead
first.
2.Remove headlamp.See ELECTRICAL,
Repair.
3.Remove headlamp mounting panel.See this
Section.
4.Remove radiator.See COOLING SYSTEM,
Repair.
5.Recover refrigerant from A/C system.See AIR
CONDITIONING, Repair.
6.Remove relevant A/C pipes.
7.Position PAS reservoir aside.
8.Remove wheel arch liner.See CHASSIS AND
BODY, Repair.
9.Remove aerial.
10.Remove vacuum solenoid valve.
11.Release clips securing coolant reservoir.
12.Remove bolts and release welds securing panel,
remove panel.
Refit13.Prepare and clean panel joint faces.
NOTE: LH panel shown
14.Reverse removal procedure.
15.Align headlamps.See ELECTRICAL,
Adjustment.
ProCarManuals.com