ecu LAND ROVER DEFENDER 1999 Service Manual

ENGINE
27
REPAIR Refit
9.Clean sump and mating faces.
10.Apply a bead of sealant, Part No. STC 3254 to
joint faces of timing chain cover and crankshaft
rear oil seal.
11.Position new sump gasket.
CAUTION: Gasket must be fitted dry.
12.Position sump, fit bolts ensuring they are in their
correct fitted position, lightly tighten bolts.
13.Fit bolts securing sump to gearbox bell housing
and tighten to15 Nm (11 lbf.ft).
14.Using sequence shown, tighten sump bolts to25
Nm (18 lbf.ft).
15.Tighten sump to gearbox bell housing bolts to50
Nm (37 lbf ft).
16.Fit new gasket to centrifuge drain pipe and
tighten bolts to10 Nm (7 lbf.ft).
17.Fit exhaust front pipe.See MANIFOLD AND
EXHAUST SYSTEM, Repair.
18.Refill engine with oil.
19.Reconnect battery negative lead.
20.Refit battery cover.
ProCarManuals.com

12ENGINE
28
REPAIR SWITCH - OIL PRESSURE
Service repair no - 12.60.50
Remove
1.Remove fixings and remove engine acoustic
cover.
2.Release clip and disconnect breather hose from
camshaft cover.
3.Release clips and disconnect air flow meter from
air filter.
4.Disconnect multiplug from air flow meter.
5.Release clip screw and remove air inlet hose
from turbocharger.
6.Remove 3 bolts and remove exhaust manifold
heat shield.
7.Disconnect multiplug from oil pressure switch.
8.Position container below switch to catch oil
spillage.
9.Remove oil pressure switch.
Refit
10.Clean oil pressure switch threads.
11.Fit oil pressure switch and tighten to9Nm(7
lbf.ft).
12.Connect switch multiplug.
13.Position exhaust manifold heat shield and
tighten M6 bolts to10 Nm (7 lbf.ft)and M8 bolt
to25 Nm (18 lbf.ft).
14.Position air inlet hose to turbocharger and
tighten clip screw.
15.Connect air flow meter to air filter and secure
clips.
16.Connect air flow meter multiplug.
17.Connect breather hose and secure clip.
18.Fit and secure engine acoustic cover.
19.Top up engine oil.
ProCarManuals.com

12ENGINE
30
REPAIR Refit
10.Clean oil cooler and mating faces.
11.Fit oil pressure switch and tighten to9Nm(7
lbf.ft).
12.Position oil cooler using a new gasket and
tighten bolts to25 Nm (18 lbf.ft).
13.Position oil filter adaptor, fit new gasket and
tighten bolts to25 Nm (18 lbf.ft).
14.Position oil filter element hand tight then a
further half turn.
15.Position coolant hose to oil cooler and secure
clip.
16.Position coolant pipe and tighten clutch housing
bolt to50 Nm (37 lbf.ft).
17.Connect oil pressure switch multiplug.
18.Fit centrifuge assembly.See this Section.
19.Refill cooling system.See COOLING SYSTEM,
Adjustment.
20.Top up engine oil.CENTRIFUGE ASSEMBLY
Service repair no - 12.60.90
Remove
1.Remove fixings and remove underbelly panel.
See CHASSIS AND BODY, Repair.
2.Remove 2 bolts securing centrifuge drain pipe to
engine sump and discard gasket.
3.Remove turbocharger.See FUEL SYSTEM,
Repair.
Models with air conditioning only
4.Remove auxiliary drive belt.See
ELECTRICAL, Repair.
5.Remove 4 bolts securing compressor and move
to one side.
ProCarManuals.com

ENGINE
31
REPAIR All Models
6.Remove 3 bolts securing centrifuge to engine oil
cooler.
7.Remove centrifuge and discard’O’ring.
8.Remove 2 bolts, remove drain pipe from
centrifuge and discard gasket.Refit
9.Clean mating faces of centrifuge, oil cooler and
sump.
10.Position drain pipe to centrifuge using new
gasket and tighten bolts to10 Nm (7 lbf.ft).
11.Position new’O’ring to oil cooler.
12.Position centrifuge and tighten bolts to25 Nm
(18 lbf.ft).
13.Align drain pipe to sump, fit new gasket and
tighten bolts to10 Nm (7 lbf.ft)
Models with air conditioning only
14.Position compressor and tighten bolts to25 Nm
(18 lbf.ft).
15.Fit auxiliary drive belt.See ELECTRICAL,
Repair.
All Models
16.Fit turbocharger.See FUEL SYSTEM, Repair.
17.Fit underbelly panel.See CHASSIS AND
BODY, Repair.
ProCarManuals.com

ENGINE
33
REPAIR TIMING CHAIN AND SPROCKETS
Service repair no - 12.65.13
Remove
1.Remove crankshaft front oil seal.See this
Section.
2.Remove cylinder head gasket.See this
Section.
3.Remove sump gasket.See this Section.
4.Release clip securing vacuum pump drain hose
to timing chain cover.
5.Remove 8 bolts securing timing chain cover.
6.Remove cover.
7.Remove timing chain and camshaft sprocket.
8.Remove 2 bolts and remove timing chain fixed
guide.
9.Remove bolt and remove timing chain adjustable
guide.
10.Remove bolt securing oil pump drive sprocket.
11.Remove crankshaft sprocket, oil pump drive
chain and sprocket.
12.Remove bolt and remove timing chain lubrication
jet.
Refit
13.Clean timing chain lubrication jet.
14.Fit lubrication jet and tighten bolt to10 Nm (7
lbf.ft).
15.Clean oil pump drive sprocket bolt threads.
16.Clean timing sprockets and chain guides.
17.Ensure that crankshaft is set to TDC firing No. 1
cylinder.
18.Fit oil pump drive chain to crankshaft sprocket
and fit sprocket to crankshaft.
19.Fit sprocket to oil pump.
20.Apply Loctite 242 to oil pump sprocket bolt
threads and tighten bolt to25 Nm (18 lbf.ft).
21.Fit timing chain fixed guide and tighten M10 bolt
to45 Nm (34 lbf.ft)and M6 bolt to10 Nm (7
lbf.ft).
22.Fit timing chain adjustable guide and tighten bolt
to25 Nm (18 lbf.ft).
ProCarManuals.com

12ENGINE
34
REPAIR
23.Fit camshaft sprocket to timing chain with timing
mark between the 2 bluelinks.
24.Fit timing chain to crankshaft sprocket aligning
blue link to timing mark.
25.Clean timing cover and mating face.
26.Apply an even film of sealant, Part No. STC
4600 to timing cover and spread to an even film
using a roller.
CAUTION: Assembly and bolt tightening
must be completed within 20 minutes of
applying sealant.
27.With assistance, fit timing cover, connect
vacuum pump drain hose and working
progressively, tighten bolts to27 Nm (20 lbf.ft).
28.Secure vacuum hose clip.
29.Fit cylinder head gasket.See this Section.
30.Fit sump gasket.See this Section.
31.Fit crankshaft front oil seal.See this Section.
ProCarManuals.com

ENGINE
1
OVERHAUL GASKET - INLET MANIFOLD
Service repair no - 30.15.08.01
Remove
NOTE: The following procedure covers
both EU3 and non EU3 engines
NOTE: EU3 Engine in main illustration, Pre
EU3 condition shown in inset.
1.Remove and discard 2 Allen screws securing
EGR pipe or EGR cooler to exhaust manifold.
2.Remove bolt securing EGR pipe to cylinder
head, (if fitted)
3.Disconnect multiplug from IAT and MAP sensor.
4.Remove 4 bolts securing fuel cooler to inlet
manifold. and remove cooler.
5.Remove bolt securing engine dipstick tube to
camshaft carrier.
6.Release and remove engine dipstick tube.
7.Remove’O’ring from dip stick tube.
8.Disconnect 4 leads from glow plugs.
9.Remove 2 nuts and 8 bolts and remove inlet
manifold.
10.Remove manifold gasket.Refit
1.Clean inlet manifold and mating face, clean
mating faces of EGR pipe, exhaust manifold and
EGR cooler (if fitted).
2.Fit new gasket.
3.Position inlet manifold and working from the
centre outwards, fit inlet manifold nuts and bolts
and tighten to25 Nm (18 lbf.ft).
4.Connect glow plug leads.
5.Clean engine dipstick tube.
6.Fit new’O’ring to dipstick tube.
7.Fit engine dipstick tube to camshaft carrier and
tighten bolt to10 Nm (7 lbf.ft).
8.Position fuel cooler and tighten bolts to25 Nm
(18 lbf.ft).
9.Connect multiplug to IAT and MAP sensor.
10.Position EGR pipe or EGR cooler to exhaust
manifold and using new Allen screws tighten to
10 Nm (7 lbf.ft).
11.Fit EGR pipe clamp to cylinder head, (if fitted)
and tighten bolt to10 Nm (7 lbf.ft).
ProCarManuals.com

12ENGINE
2
OVERHAUL GASKET - EXHAUST MANIFOLD
Service repair no - 30.15.12.01
Remove
NOTE: The following procedure covers
both EU3 and non EU3 engines
NOTE: EU3 engine illustrated.
1.Remove 3 bolts securing heater pipe to cylinder
head and turbocharger heat shield.
2.Remove heater pipe.
3.Remove bolt and remove turbocharger heat
shield.
4.Remove and discard 2 Allen screws securing
EGR pipe to exhaust manifold.
5.Remove banjo bolt securing oil feed pipe to
turbocharger and discard sealing washers.
6.Loosen turbocharger drain hose union at
cylinder block.
7.Remove 10 nuts and remove exhaust manifold
and turbocharger.
8.Remove manifold gasket.Refit
1.Clean exhaust manifold mating faces.
2.Position exhaust manifold to cylinder head using
new gasket and fit manifold nuts.
3.Working from the centre outwards, fit and tighten
nuts to25 Nm (18 lbf.ft).
4.Clean turbocharger drain and feed hose unions.
5.Fit turbocharger oil drain hose to cylinder block
and tighten union to48 Nm (35 lbf.ft).
6.Fit new sealing washers to turbocharger oil feed
pipe, fit banjo bolt and tighten to25 Nm (18
lbf.ft).
7.Position EGR pipe to exhaust manifold. Fit new
Allen screws and tighten to10 Nm (7 lbf.ft).
8.Position turbocharger heat shield.
9.Position heater pipe to cylinder head and tighten
bolts to25 Nm (18 lbf.ft).
10.Position exhaust manifold heatshield and tighten
M6 bolts to9 Nm (7 lbf.ft)and M8 bolt to25
Nm (18 lbf.ft).
ProCarManuals.com

ENGINE
3
OVERHAUL GASKET - CYLINDER HEAD
Service repair no - 12.29.02.01
Remove
CAUTION: The following procedures
should only be carried out when cylinder
head is to be overhauled; for replacement
of cylinder head gasket only, see Repairs section -
Gasket - Cylinder head.
NOTE: The following procedure covers
both EU3 and non EU3 engines
1.Remove exhaust manifold gasket.See
MANIFOLD AND EXHAUST SYSTEM, Repair.
2.Remove inlet manifold gasket.See MANIFOLD
AND EXHAUST SYSTEM, Repair.
3. Models with EGR cooler:Remove and discard
2 Allen screws securing EGR pipe to cooler.
4.Progressively loosen then remove 13 bolts
securing camshaft cover, remove cover; remove
and discard gasket.
5.Remove isolators and sealing washers from
cover.
6.Disconnect injector multiplug from camshaft
carrier.
7.Disconnect multiplug from ECT sensor.
8.Remove bolt securing alternator strap bracket to
cylinder head.
9.Set engine to TDC firing - No. 1 cylinder -
coloured links on timing chain are aligned with
timing mark on camshaft sprocket.
10.Fit timing pinLRT-12-058into slot in camshaft.
ProCarManuals.com

12ENGINE
4
OVERHAUL
11.Disconnect alternator/vacuum pump oil feed pipe
union from cylinder head, remove and discard
’O’ring.
12.Remove camshaft sprocket access plug from
front of cylinder head, remove and discard’O’
ring.
13.Remove timing chain fixed guide Allen screw.
14.Remove timing chain tensioner, remove and
discard sealing washer.
15.Remove and discard 3 bolts securing camshaft
sprocket to camshaft; release sprocket from
camshaft.
16.Remove bolt and nut securing front of cylinder
head to timing chain cover.
17.Using sequence shown, progressively loosen
then remove 12 cylinder head bolts; discard
bolts together with their captive washers.
18.Using assistance, remove cylinder head and
place on 2 wooden blocks.
CAUTION: Cylinder head is dowel located,
do not tap it sideways to free it from
cylinder block. Support both ends of
cylinder head on blocks of wood. With the
camshaft carrier bolted down, the injector nozzles
and some of the valves will protrude from the face
of the cylinder head.
19.Remove the cylinder head gasket.
20.Note the gasket thickness indicator and ensure
the same thickness gasket is used on refitment
of the cylinder head.
CAUTION: If new pistons, connecting rods
or crankshaft are fitted, it will be
necessary to measure piston stand proud
in order to determine thickness of gasket
required.See this Section.
21.Remove and discard 2 plastic locating dowels
from cylinder block.
22.Carry out cylinder head overhaul procedures.
See this Section.
ProCarManuals.com