ecu LAND ROVER DEFENDER 1999 Owner's Manual

ENGINE
3
REPAIR
25.Using sequence shown, progressively tighten
bolts to25 Nm (18 lbf.ft).
26.Lubricate a new camshaft rear oil seal with
engine oil, fit seal using a suitable mandrel.
27.Fit rocker shaft ensuring it is located on dowel, fit
new bolts and working from the centre outwards,
tighten bolts progressively to32 Nm (24 lbf.ft).
28.Fit new’O’ring to injector harness multiplug, fit
harness and connect injector multiplugs.
29.Fit cylinder head gasket.See this Section.
30.Before refitting the camshaft cover the fuel
injector rockers must be adjusted.
31.Rotate engine clockwise until No. 1 injector lobe
is at full lift.
32.Rotate rocker adjusting screw clockwise until the
injector plunger is felt to bottom out.
33.Rotate rocker adjusting screw anti-clockwise 1
complete turn to give plunger the required bump
clearance and tighten rocker adjusting screw
locknut to16 Nm (12 lbf.ft).
34.Carry out above procedure for the remaining 4
rockers.
35.After completion of rocker adjustment, slowly
rotate engine clockwise 2 complete turns by
hand to ensure that no injectors are bottoming
out on their plungers.PULLEY - CRANKSHAFT
Service repair no - 12.21.01
Remove
1.Remove underbelly panel.See CHASSIS AND
BODY, Repair.
2.Remove radiator.See COOLING SYSTEM,
Repair.
3.Using a 15 mm ring spanner release the
auxiliary drive belt tensioner.
4.Remove auxiliary drive belt.
5.Remove 3 bolts and remove crankshaft damper.
6.PositionLRT-51-003to crankshaft pulley and
secure with 2 bolts.
7.Remove and discard crankshaft pulley bolt.
Remove crankshaft pulley.
8.Remove 2 bolts and removeLRT-51-003.
ProCarManuals.com

12ENGINE
4
REPAIR Refit
9.Position new crankshaft pulley to vice.
10.Remove 3 bolts and remove damper from
crankshaft pulley.
11.Using a lint free cloth, thoroughly clean oil seal
recess and the running surface on crankshaft
pulley.
12.Fit crankshaft pulley.
13.FitLRT-51-003to crankshaft pulley and secure
with 2 bolts.
14.Fit new crankshaft pulley bolt and tighten to460
Nm (340 lbf.ft).
NOTE: It is recommended that a torque
multiplier is used to tighten crankshaft
pulley bolt.
15.Remove 2 bolts and removeLRT-51-003from
crankshaft pulley.
16.Fit damper to crankshaft pulley, fit bolts and
tighten to80 Nm (60 lbf.ft).
17.Fit auxiliary drive belt.
18.Fit radiator.See COOLING SYSTEM, Repair.
19.Fit underbelly panel.See CHASSIS AND
BODY, Repair.OIL SEAL - CRANKSHAFT - REAR
Service repair no - 12.21.20
Remove
1.Remove flywheel.See this Section.
2.Remove sump gasket.See this Section.
3.Remove 5 bolts securing oil seal housing to
cylinder block.
4.Remove seal housing.
Refit
5.Clean seal housing mating face on cylinder
block.
6.Position seal protector,LRT-12-061over
crankshaft boss. Fit new seal and housing
assembly and remove toolLRT-12-061.
CAUTION: Oil seal must be fitted dry.
ProCarManuals.com

12ENGINE
6
REPAIR GASKET - CYLINDER HEAD
Service repair no - 12.29.02
Remove
NOTE: The following procedures cover
engines fitted with or without an EGR
cooler. The EGR cooler is bolted to the
front of the cylinder head.
1.Remove underbelly panel.See CHASSIS AND
BODY, Repair.
2.Drain cooling system.See COOLING
SYSTEM, Adjustment.
3.Remove camshaft cover gasket.See this
Section.
4.Remove cooling fan.See COOLING SYSTEM,
Repair.
5.Release clips and disconnect air flow meter from
air filter.
6.Disconnect multiplug from air flow meter.
7.Loosen clip and remove air inlet hose from
turbocharger.
8.Remove 3 bolts and remove exhaust manifold
heat shield.
9.Remove turbocharger oil feed banjo bolt and
discard sealing washers.
10.Remove 3 nuts, release turbocharger from
exhaust manifold, discard gasket and tie
turbocharger aside.
11.Remove 2 bolts securing engine harness to
camshaft carrier.
12.Disconnect fuel injector, coolant and compressor
sensors.
13.Disconnect 4 heater plug connectors.
ProCarManuals.com

ENGINE
7
REPAIR
14.Disconnect MAP sensor multiplug from inlet
manifold.
15.Position engine harness clear of inlet manifold.
16.Disconnect vacuum hose from EGR valve.
17.Loosen clip screw and disconnect air intake
hose from EGR valve.
18.Release 3 clips and disconnect coolant hoses
from fuel cooler.
19.Disconnect fuel hoses, tank to fuel cooler and
connector block on cylinder head.
CAUTION: Plug the connections.
20.Disconnect fuel hose from fuel cooler and secure
to connector block on cylinder head. This is to
prevent contamination of the fuel injection
system.
ProCarManuals.com

12ENGINE
8
REPAIR
NOTE: Non EU3 model illustrated.
21.Loosen vacuum pipe union from cylinder head
and discard’O’ring.
22.Loosen 2 bolts and release alternator support
bracket from cylinder head.
23. Pre EU3 model:-Remove bolt securing EGR
valve pipe to cylinder head.
24. EU3 model:-Release the clips and disconnect
the coolant hoses from the EGR cooler.
25.Release clips and disconnect top hose, heater
hose and heater feed hose.
26.Remove the nut and bolt securing the cuylinder
head to the timing chain cover.
27.Rotate engine clockwise to align mark on
camshaft sprocket between coloured links on
timing chain.
28.PositionLRT-12-058through camshaft carrier to
lock camshaft.
29.PositionLRT-12-158through gearbox bell
housing to lock crankshaft.
ProCarManuals.com

12ENGINE
10
REPAIR Refit
39.Clean mating faces of cylinder head and cylinder
block.
40.Check cylinder head for warping, across centre
and from corner to corner:
Maximum warp = 0.10 mm (0.004 in)
CAUTION: Cylinder heads may not be
refaced, replace cylinder head assembly if
warping exceeds figure given.
41.Ensure coolant and oil passages are clean.
42.Clean dowel holes and fit new dowels.
43.Fit new cylinder head gasket of the correct
thickness with the word’TOP’uppermost.
44.Using assistance, fit cylinder head and locate on
to dowels.
45.Carefully enter new cylinder head bolts together
with their captive washers,DO NOT DROP.
Lightly tighten bolts.
46.Using sequence shown, tighten cylinder head
bolts to:-
Stage 1 -30 Nm (23 lbf.ft)
Stage 2 -65 Nm (48 lbf.ft)
Stage 3 -90°
Stage 4 -Further 180°
Stage 5 -Further 45°
CAUTION: Ensure correct tightening
sequence is followed for all 5 tightening
stages. Do not tighten bolts 315°in one
operation.
47.Fit nut and bolt securing cylinder head to timing
chain cover and tighten to25 Nm (18 lbf.ft).
48.Clean camshaft sprocket and mating face on
camshaft.
49.Ensure engine is set to TDC No. 1 cylinder and
mark on camshaft sprocket is positioned
between the 2 coloured links.
50.Position camshaft sprocket to camshaft, fit and
lightly tighten new bolts then loosen bolts half a
turn.
51.Clean fixed guide retaining pin and apply Loctite
242 to threads.
52.Fit and tighten fixed guide retaining pin to25 Nm
(18 lbf.ft).
53.Clean timing chain tensioner and fit new sealing
washer.
54.Fit timing chain tensioner and tighten to45 Nm
(33 lbf.ft).
55.Tighten camshaft sprocket retaining bolts to36
Nm (27 lbf.ft).
56.RemoveLRT-12-058from camshaft.
57.RemoveLRT-12-158from gearbox bell housing.
58.Clean access plug recess in cylinder head and
fit new’O’ring. Fit access plug.
59.Clean vacuum pump union.
60.Tighten vacuum pipe union to10 Nm (7lbf.ft).
61.Fit bolts securing alternator bracket to cylinder
head and tighten to25 Nm (18 lbf.ft).
62.Connect top hose, heater hoses and secure with
clips.
ProCarManuals.com

ENGINE
11
REPAIR 63. Pre EU3 model:-Fit bolt, EGR valve pipe to
cylinder head and tighten to25 Nm (18 lbf.ft).
64. EU3 model:-Connect coolant hoses to EGR
cooler and secure with clips.
65.Position air intake hose to EGR valve and
tighten clip screw.
66.Disconnect fuel hose from connector block and
connect to fuel cooler.
67.Connect fuel hoses to fuel cooler and connector
block on cylinder head.
68.Connect coolant hoses to fuel cooler and secure
clips.
69.Connect vacuum hose to EGR valve.
70.Position engine harness and connect multiplugs
and heater plug connectors.
71.Fit and tighten bolts, engine harness to camshaft
carrier.
72.Clean exhaust manifold and mating face.
73.Fit new gasket to exhaust manifold, position
turbocharger and tighten nuts to30 Nm (22 lbf.
ft).
74.Clean turbocharger feed hose bolt.
75.Position feed hose using new sealing washers,
tighten bolt to25 Nm (18 lbf.ft).
76.Position exhaust manifold heat shield, and
tighten M6 bolts to10 Nm (7 lbf.ft)and M8 bolt
to25 Nm (18 lbf.ft).
77.Position air inlet hose to turbocharger and
tighten clip screw.
78.Connect air flow meter to air filter and secure
clips.
79.Connect air flow meter multiplug.
80.Fit cooling fan.See COOLING SYSTEM,
Repair.
81.Fit camshaft cover gasket.See this Section.
82.Refill cooling system.See COOLING SYSTEM,
Adjustment.
83.Fit underbelly panel.See CHASSIS AND
BODY, Repair.ROCKER SHAFT ASSEMBLY
Service repair no - 12.29.29
Remove
1.Remove cooling fan.See COOLING SYSTEM,
Repair.
2.Remove camshaft cover gasket.See this
Section.
3.Loosen lock nuts and fully retract rocker
adjusting screws to prevent damage on
reassembly.
4.Rotate engine clockwise, until camshaft gear
and timing chain marks are aligned and fit
LRT-12-058through camshaft carrier to lock
camshaft.
ProCarManuals.com

12ENGINE
14
REPAIR
9. Not EU3 model:-Apply two 3 mm diameter
beads of sealant, Part No.STC 5433 to areas’A’
shown on illustration.
CAUTION: Excessive use of sealant could
result in blockage of oil drain hole,
arrowed’B’in illustration.
10.Fit new gasket to camshaft cover. fit cover and
tighten bolts to10 Nm (7 lbf.ft).
11.Position breather hose and secure clip.
12.Fit engine acoustic cover.
13.Reconnect battery negative lead.
14.Fit battery cover.ENGINE AND ANCILLARIES
Service repair no - 12.41.01.99
Remove
1.Remove underbelly panel.See CHASSIS AND
BODY, Repair.
2.Drain engine oil.
3.Remove radiator.See COOLING SYSTEM,
Repair.
4.Remove turbocharger.See FUEL SYSTEM,
Repair.
5.Remove starter motor.See ELECTRICAL,
Repair.
6.Remove air filter.See FUEL SYSTEM, Repair.
7.Loosen clip screw and release air intake hose
from intake elbow.
8.Release clips and disconnect coolant hoses
from fuel cooler and coolant rail.
ProCarManuals.com

ENGINE
15
REPAIR
NOTE: Non EU3 model illustrated.
9.Disconnect fuel hoses, tank to fuel cooler and
connector block on cylinder head.
CAUTION: Plug the connections.
10.Disconnect fuel hose from fuel cooler and secure
to connector block on cylinder head. This to
prevent contamination of the fuel system.
11.Release servo vacuum pipe, remove 4 bolts and
remove fuel cooler.
12.Release servo vacuum pipe from engine rear
cover clips and vacuum pump.
NOTE: Non EU3 model illustrated.
13.Disconnect vacuum hose from EGR valve.
14.Release EGR vacuum hose from vacuum pipe.
15.Disconnect multiplug from condensor cooling
fan.
NOTE: Non EU3 model illustrated.
16.Disconnect multiplugs from EGR solenoid, inlet
manifold sensor and injector harness.
ProCarManuals.com

12ENGINE
16
REPAIR
NOTE: Non EU3 model illustrated.
17.Disconnect multiplug from fuel temperature
sensor.
18.Disconnect multiplug from CKP sensor. Remove
bolt securing CKP sensor, remove sensor and
discard’O’ring.
CAUTION: If fitted:- Retain CKP sensor
spacer.
19.Disconnect 4 glow plug leads.
20.Remove nut securing alternator lead and
disconnect multiplug.
NOTE: Non EU3 model illustrated.
21.Remove 2 bolts securing engine harness to
camshaft carrier.
22.Disconnect A/C compressor and ECT sensor
multiplugs.
ProCarManuals.com