coolant LAND ROVER DEFENDER 1999 Repair Manual

26COOLING SYSTEM
2
REPAIR PUMP - COOLANT
Service repair no - 26.50.01
Remove
1.Drain cooling system.See Adjustment.
2.Remove centrifuge.See ENGINE , Repair.
3.Release clip and hose from coolant pump cover.
4.Remove 5 bolts securing coolant pump cover.
5.Remove cover and coolant pump from housing
and discard’O’rings.Refit
6.Clean coolant pump housing and mating faces.
7.Fit new’O’rings to coolant pump and cover.
8.Fit coolant pump and cover and tighten bolts to9
Nm (7 lbf.ft).
9.Connect hose to pump cover and secure clip.
10.Refit centrifuge.See ENGINE , Repair.
11.Refill cooling system.See Adjustment.
ProCarManuals.com

COOLING SYSTEM
3
REPAIR RADIATOR
Service repair no - 26.40.01
Remove
1.Remove front grille.See CHASSIS AND
BODY, Repair.
2.Drain cooling system.See Adjustment.
3.Remove cooling fan.See this Section.
4.Remove 5 bolts and move bonnet platform
aside.
5.Release clip and disconnect bleed hose from
radiator.
6.Release clip and disconnect top hose from
radiator.
7.Release clip and disconnect fuel cooler hose
from radiator.
8.Release clip and disconnect coolant rail hose
from radiator.
ProCarManuals.com

COOLING SYSTEM
5
REPAIR Refit
17.Fit rubber mountings to bottom of radiator.
18.Fit lower cooling fan cowl to radiator and secure
with screws.
19.Fit nuts to radiator side brackets.
20.Position intercooler to radiator and tighten bolts.
21.Fit rubber mountings to intercooler.
22.Position mounting spacers and fit radiator.
23.Fit bottom hose into bracket on lower cooling fan
cowl.
24.Position air hose to turbocharger pipe and
secure with clip.
25.Position LH and RH radiator mounting brackets
to body and radiator and tighten bolts.
26.Position coolant rail hose to radiator and secure
with clip.
27.Position fuel cooler hose to radiator and secure
with clip.
28.Position top hose to radiator and secure with
clip.
29.Position bleed hose to radiator and secure with
clip.
30.Position bonnet platform and tighten bolts.
31.Fit cooling fan.See this Section.
32.Fit front grille.See CHASSIS AND BODY,
Repair.
33.Fill cooling system.See Adjustment.
ProCarManuals.com

77PANEL REPAIRS
2
REPAIR WING UPPER - LH
Remove
1.Disconnect both battery leads, negative lead
first.
2.Remove headlamp.See ELECTRICAL,
Repair.
3.Remove headlamp mounting panel.See this
Section.
4.Remove radiator.See COOLING SYSTEM,
Repair.
5.Recover refrigerant from A/C system.See AIR
CONDITIONING, Repair.
6.Remove receiver drier.See AIR
CONDITIONING, Repair.
7.Remove relevant A/C pipes.
8.Remove relevant heater intake pipes.
9.Remove screen washer bottle.
10.Remove wheel arch liner.See CHASSIS AND
BODY, Repair.
11.Remove bolts and release welds securing panel,
remove panel.
Refit
12.Prepare and clean panel joint faces.
13.Reverse removal procedure.
14.Align headlamps.See ELECTRICAL,
Adjustment.WING UPPER - RH
Remove
1.Disconnect both battery leads, negative lead
first.
2.Remove headlamp.See ELECTRICAL,
Repair.
3.Remove headlamp mounting panel.See this
Section.
4.Remove radiator.See COOLING SYSTEM,
Repair.
5.Recover refrigerant from A/C system.See AIR
CONDITIONING, Repair.
6.Remove relevant A/C pipes.
7.Position PAS reservoir aside.
8.Remove wheel arch liner.See CHASSIS AND
BODY, Repair.
9.Remove aerial.
10.Remove vacuum solenoid valve.
11.Release clips securing coolant reservoir.
12.Remove bolts and release welds securing panel,
remove panel.
Refit13.Prepare and clean panel joint faces.
NOTE: LH panel shown
14.Reverse removal procedure.
15.Align headlamps.See ELECTRICAL,
Adjustment.
ProCarManuals.com

AIR CONDITIONING
1
REPAIR COMPRESSOR
Service repair no - 82.10.20
Remove
1.Remove engine acoustic cover.See ENGINE ,
Repair.
2.Depressurise A/C system.See Adjustment.
3.Remove auxiliary drive belt.See
ELECTRICAL, Repair.
4.Drain cooling system.See COOLING
SYSTEM, Adjustment.
5.Disconnect multiplug from compressor.
6.Remove 2 bolts securing air conditioning pipes
to compressor and discard’O’rings.
CAUTION: Immediately cap all air
conditioning pipes to prevent ingress of
dirt and moisture into the system.
7.Release clips and disconnect top hose from
coolant elbow and heater pipe.
8.Remove 4 bolts securing compressor to
mounting bracket.
9.Remove compressor.Refit
10.Position compressor to mounting bracket and
tighten bolts to25 Nm (18 lbf.ft).
11.Remove caps from compressor and pipe
connections.
12.Clean compressor and pipe connections.
13.Lubricate new’O’rings with refrigerant oil and fit
to compressor.
14.Position A/C pipes to compressor and tighten
bolts to9 Nm (7 lbf.ft).
15.Connect multiplug to compressor.
16.Position top hose and secure with clips.
17.Refill cooling system.See COOLING SYSTEM,
Adjustment.
18.Fit auxiliary drive belt.See ELECTRICAL,
Repair.
19.Recharge A/C system.See Adjustment.
20.Fit engine acoustic cover.See ENGINE ,
Repair.
ProCarManuals.com