cooling LAND ROVER DEFENDER 1999 Repair Manual

COOLING SYSTEM
3
REPAIR RADIATOR
Service repair no - 26.40.01
Remove
1.Remove front grille.See CHASSIS AND
BODY, Repair.
2.Drain cooling system.See Adjustment.
3.Remove cooling fan.See this Section.
4.Remove 5 bolts and move bonnet platform
aside.
5.Release clip and disconnect bleed hose from
radiator.
6.Release clip and disconnect top hose from
radiator.
7.Release clip and disconnect fuel cooler hose
from radiator.
8.Release clip and disconnect coolant rail hose
from radiator.
ProCarManuals.com

26COOLING SYSTEM
4
REPAIR
9.Remove 4 bolts securing RH and LH radiator
mounting brackets to body and remove brackets.
10.Release clip and release air hose from
turbocharger inlet pipe.11.Release bottom hose from bracket on lower
cooling fan cowl.
12.Remove radiator assembly and collect lower
mounting spacers.
13.Remove 2 bolts and remove intercooler from
radiator. Collect 2 nuts from radiator side
brackets.
14.Remove 2 rubber mountings from intercooler.
15.Remove 2 screws and remove lower cooling fan
cowl from radiator.
16.Remove 2 rubber mountings from bottom of
radiator.
ProCarManuals.com

COOLING SYSTEM
5
REPAIR Refit
17.Fit rubber mountings to bottom of radiator.
18.Fit lower cooling fan cowl to radiator and secure
with screws.
19.Fit nuts to radiator side brackets.
20.Position intercooler to radiator and tighten bolts.
21.Fit rubber mountings to intercooler.
22.Position mounting spacers and fit radiator.
23.Fit bottom hose into bracket on lower cooling fan
cowl.
24.Position air hose to turbocharger pipe and
secure with clip.
25.Position LH and RH radiator mounting brackets
to body and radiator and tighten bolts.
26.Position coolant rail hose to radiator and secure
with clip.
27.Position fuel cooler hose to radiator and secure
with clip.
28.Position top hose to radiator and secure with
clip.
29.Position bleed hose to radiator and secure with
clip.
30.Position bonnet platform and tighten bolts.
31.Fit cooling fan.See this Section.
32.Fit front grille.See CHASSIS AND BODY,
Repair.
33.Fill cooling system.See Adjustment.
ProCarManuals.com

MANIFOLD AND EXHAUST SYSTEM
3
REPAIR EXHAUST - TAIL PIPE AND SILENCER
Service repair no - 30.10.22
Remove
1.Raise vehicle on ramp.
2.Remove 3 nuts securing silencer to tail pipe.
3.Release tail pipe from mounting and remove tail
pipe.
4.Collect silencer to tail pipe gasket.
Refit
5.Clean silencer and tail pipe mating faces.
6.Position tail pipe and secure on mounting
rubber.
7.Using a new gasket, align silencer to tail pipe.
8.Fit nuts to silencer and tighten to25 Nm (18
lbf.ft).GASKET - INLET MANIFOLD
Service repair no - 30.15.08
Remove
1.Remove battery cover.
2.Disconnect battery negative lead.
3.Remove 3 bolts and remove engine acoustic
cover.
4.Release retainers and remove cooling fan cowl.
5.Disconnect multiplug from manifold air pressure
sensor and release 4 glow plug leads.
6.Remove 4 bolts, release EGR valve from inlet
manifold and discard gasket.
ProCarManuals.com

MANIFOLD AND EXHAUST SYSTEM
5
REPAIR Refit
16.Clean inlet manifold and mating face.
17.Fit new gasket.
18.Fit inlet manifold, and working from the centre
outwards, tighten nuts and bolts to25 Nm (18
lbf.ft).
19.Position harness to sensors and connect
multiplugs.
20.Tighten harness clip bolts to camshaft carrier to
10 Nm (7 lbf.ft).
21.Clean dip stick tube and fit new’O’ring.
22.Fit dip stick tube and tighten bolt to10 Nm (7
lbf.ft).
23.Connect glow plug leads.
24.Fit alternator support bracket and tighten bolts to
45 Nm (33 lbf.ft).
25.Position fuel cooler. Apply Loctite 242 to bolts
and tighten to18 Nm (13 lbf.ft).
26.Fit new gasket, position EGR valve and tighten
bolts to9 Nm (7 lbf.ft).
27.Connect multiplug to MAP sensor.
28.Fit cooling fan cowl.
29.Fit engine acoustic cover.
30.Reconnect battery negative lead.
31.Fit battery cover.GASKET - EXHAUST MANIFOLD
Service repair no - 30.15.12
Remove
1.Remove turbocharger.See FUEL SYSTEM,
Repair.
2. Models with A/C:Remove auxiliary drive belt.
See ELECTRICAL, Repair.
3.Remove 4 bolts securing compressor and move
to one side.
All Models
NOTE: EU3 Model illustrated.
4.Remove and discard 2 Allen screws securing
EGR pipe to exhaust manifold.
5.Remove 10 nuts securing exhaust manifold to
cylinder head.
6.Remove exhaust manifold and gasket.
ProCarManuals.com

37MANUAL GEARBOX
8
REPAIR
12.Remove 13 screws securing tunnel cover.
13.Release and remove tunnel cover.
14.Remove cooling fan.See COOLING SYSTEM,
Repair.
15.Remove air filter.See FUEL SYSTEM, Repair.
16.Remove 2 upper bolts securing clutch housing to
engine.
17.Remove bolt securing shim to clutch housing.
18.Release gearbox breather pipes from clips on
heater hose.
19.Remove starter motor.See ELECTRICAL,
Repair.
20.Remove exhaust front pipe.See MANIFOLD
AND EXHAUST SYSTEM, Repair.
21.Drain gearbox oil.See Adjustment.
22.Drain transfer gearbox oil.See
MAINTENANCE ,
23.Remove 3 nuts securing intermediate silencer to
tail pipe.
24.Release silencer from mounting rubbers, remove
silencer and discard gasket.
25.Mark front and rear propeller shaft to transfer
gearbox flanges for reassembly purposes.
ProCarManuals.com

MANUAL GEARBOX
11
REPAIR Refit
44.Clean gearbox to engine mating faces, dowels
and dowel holes.
45.With assistance raise gearbox on jack and align
to clutch and engine.
46.Fit lower bolts securing clutch housing to engine
and tighten to50 Nm (37 lbf.ft).
NOTE: Do not fit upper bolts at this stage.
47.Fit earth leads and secure with bolt.
48.Connect Lucars to differential lock switch,
multiplug to reverse light switch, position
multiplug to bracket and connect low ratio detect
multiplug - if fitted.
49.Raise gearbox jack and guide transfer gearbox
lever through tunnel.
50.Secure body harness clips to bracket on top of
transfer gearbox.
51.Position battery earth lead to transfer gearbox
and tighten retaining nut.
52.Connect multiplug to speed sensor and secure
harness in clip on transfer gearbox.
53.Position mounting brackets and rubber
mountings, positioning heat shield to LH
mounting and tighten bracket bolts to85 Nm (63
lbf.ft).
54.Position nuts to mountings and tighten to48 Nm
(35 lbf.ft).
55.Remove 3 bolts securing support plate
LRT-99-007to gearbox.
56.Position handbrake cable through heel board.
57.Position clutch slave cylinder, fit bolts and
tighten to25 Nm (18 lbf.ft).
58.Clean propeller shafts and mating faces.
59.Position propeller shafts, align to marks and
tighten nuts to48 Nm (35 lbf.ft).
60.Clean intermediate silencer and tail pipe mating
faces.
61.Position silencer and secure on mountings,
using a new gasket align to tail pipe, fit nuts and
tighten to25 Nm (18 lbf.ft).
62.Refill gearbox with oil.See Adjustment.
63.Refill transfer gearbox with oil.See
MAINTENANCE ,
64.Fit exhaust front pipe.See MANIFOLD AND
EXHAUST SYSTEM, Repair.
65.Refit starter motor.See ELECTRICAL, Repair.
66.Fit bolt securing shim plate to clutch housing and
tighten10 Nm (7 lbf.ft).
67.Position heater pipe to gearbox housing, fit
upper bolts securing clutch housing to engine
and tighten to50 Nm (37 lbf.ft).
68.Position gearbox breather pipes to clips on
heater hose.69.Fit air cleaner.See FUEL SYSTEM, Repair.
70.Fit cooling fan.See COOLING SYSTEM,
Repair.
71.Fit and align tunnel cover, fit and tighten screws.
72.Position relay panel, fit spacers and tighten
screws.
73.Position hand-brake lever and tighten bolts to25
Nm (18 lbf.ft).
74.Connect handbrake cable to lever, fit clevis pin,
washer and new split pin.
75.Connect Lucar to hand-brake switch.
76.Position gaiter to handbrake lever and secure
with trim stud.
77.Locate insulation pad over gear levers and fit to
tunnel cover.
78.Align spline marks, fit gear lever to lower lever,
fit washer and secure with retaining nut.
79.Position gear lever cover.
80.Position gearbox tunnel carpet.
81.Fit gear lever and transfer gear lever knobs.
82.Reconnect battery negative lead.
83.Fit battery cover.
ProCarManuals.com

41TRANSFER GEARBOX
2
REPAIR
13.Release handbrake outer cable from heelboard.
14.Remove breather pipe banjo bolt from transfer
gearbox high/low cross shaft housing and
discard sealing washers.
15.Remove retaining clip and disconnect high/low
operating rod from lever.
16.Remove cooling fan.See COOLING SYSTEM,
Repair.
17.Remove front exhaust pipe.See MANIFOLD
AND EXHAUST SYSTEM, Repair.
18.Drain transfer gearbox oil.
19.Remove 3 nuts securing intermediate silencer to
tail pipe.
20.Release intermediate silencer from rubber
mountings and remove silencer from tail pipe,
discard gasket.
21.Using a centre punch, mark relationship between
front propeller shaft and transfer gearbox drive
flanges and rear propeller shaft and brake drum
drive flanges.
22.Remove 4 nuts securing front propeller shaft to
transfer gearbox drive flange and remove
propeller shaft.
23.Remove 4 nuts securing rear propeller shaft to
brake drum flange.
24.Release propeller shaft and tie aside.
ProCarManuals.com

41TRANSFER GEARBOX
6
REPAIR 71.Release propeller shaft, align flange markings
and connect to studs.
72.Fit nuts securing propeller shaft and tighten to48
Nm (33 lbf.ft).
73.Clean front propeller to transfer gearbox flange
mating faces.
74.Fit propeller shaft, align flange markings and
tighten nuts to48 Nm (33 lbf.ft).
75.Using new gasket, fit intermediate silencer and
tighten nuts to25 Nm (18 lbf.ft).
76.Fit exhaust front pipe.See MANIFOLD AND
EXHAUST SYSTEM, Repair.
77.Refill transfer gearbox with recommended oil.
78.Fit cooling fan cowl.
79.Fit high/low operating rod and secure with
retaining clip.
80.Position handbrake outer cable to heelboard.
81.Position handbrake cable to lever, fit clevis pin,
washer and new split pin.
82.Position handbrake gaiter and secure with trim
studs.
83.Fit insulation pad to tunnel.
84.Fit gear lever cover.
85.Fit gear lever knobs.
86.Position diagnostic plug bracket, access panel
and tighten screws.
87.Fit carpet to transmission tunnel.
88.Fit cubby box.See CHASSIS AND BODY,
Repair.
89.Fit cooling fan.See COOLING SYSTEM,
Repair.
90.Reconnect battery negative lead.
91.Fit battery cover.GASKET - REAR COVER PLATE
Service repair no - 41.20.30
Remove
1.Raise vehicle on’4 post ramp’.
2.Mark rear cover plate to bearing housing for
assembly purposes.
3.Noting fitted position of stud bolt and harness
clip bracket, remove 5 bolts and stud bolt
securing cover plate.
4.Collect harness clip bracket.
5.Remove cover plate.
Refit
6.Clean cover plate and mating face.
7.Apply Hylosil RTV 102 to rear cover mating face.
8.Align reference marks, fit cover plate.
9.Clean cover bolts and apply Loctite 290 threads
of bolts and stud nut.
10.Position clip bracket, fit stud nut and bolts,
tighten by diagonal selection to25 Nm (18
lbf.ft).
11.Check/top-up transfer gearbox oil.
12.Lower vehicle.
ProCarManuals.com

76CHASSIS AND BODY
4
REPAIR WING - FRONT
Service repair no - 76.10.24
Remove
1.Remove wheel arch liner.See this Section.
2.Remove front grille.See this Section.
3.Release fixings and remove cooling fan cowl.
4.Remove air cleaner grille from front wing.
5.Remove 4 screws securing air intake elbow to
wing.
6.Remove 7 screws and remove heater air intake
grille from wing.
7.Remove 2 bolts securing heater air intake
bracket to inner wing. Remove bracket.
8.Remove heater air intake from wing and collect
seal.
9.Remove 2 bolts securing EGR solenoid to inner
wing and lay aside.
10.Remove 3 studs securing expansion tank pipe to
inner wing.
11.Remove 2 bolts securing PAS reservoir to inner
wing and lay aside.
12.Remove 4 bolts securing outer wing to inner
wing.
ProCarManuals.com