alignment LAND ROVER DEFENDER 1999 Workshop Manual

10 - MAINTENANCE
CONTENTS
Page
MAINTENANCE
UNDERBONNET VIEW - Td5 1..............................................................................
SEATS AND SEAT BELTS 2..................................................................................
LAMPS, HORNS AND WARNING INDICATORS 2................................................
WIPERS AND WASHERS 3...................................................................................
HANDBRAKE 3.......................................................................................................
BATTERY CONDITION - Td5 4..............................................................................
HANDSET BATTERY 5...........................................................................................
HEADLAMP ALIGNMENT 5....................................................................................
ROAD WHEELS 6...................................................................................................
TYRE PRESSURES, CONDITION AND TREAD DEPTH 6....................................
BRAKE PADS, CALIPERS AND DISCS 7..............................................................
ROAD WHEEL SPEED SENSOR HARNESS - Td5 7............................................
FUEL FILTER ELEMENT 8.....................................................................................
FUEL FILTER SEDIMENTER - Td5 8.....................................................................
INTERCOOLER / COOLING SYSTEM 9................................................................
AMBIENT AIR PRESSURE (AAP) SENSOR - Td5 9..............................................
DOOR LOCKS AND HINGES 10............................................................................
ENGINE COOLANT 10...........................................................................................
BRAKE FLUID 11....................................................................................................
AIR FILTER ELEMENT AND DUMP VALVE 11.....................................................
AUXILIARY DRIVE BELT 12...................................................................................
PAS FLUID, CLUTCH FLUID AND SCREEN WASHER LEVELS 12.....................
STEERING BOX 13................................................................................................
ENGINE OIL 14.......................................................................................................
CENTRIFUGE ROTOR - Td5 14.............................................................................
FULL FLOW OIL FILTER 15...................................................................................
GEARBOX OIL 15...................................................................................................
TRANSFER BOX OIL 16.........................................................................................
FRONT AND REAR AXLE OIL 17..........................................................................
PROPELLER SHAFTS 18.......................................................................................
CLUTCH PIPES AND UNIONS 18..........................................................................
PAS PIPES AND UNIONS 19.................................................................................
ENGINE, GEARBOX, TRANSFER BOX AND AXLES 19.......................................
EXHAUST SYSTEM 20...........................................................................................
STEERING BOX AND SUSPENSION 20...............................................................
STEERING BALL JOINTS 21.................................................................................
SHOCK ABSORBERS 22.......................................................................................
TOWING BRACKET 22...........................................................................................
ENGINE AND TRANSMISSION MOUNTINGS 23..................................................
ProCarManuals.com

MAINTENANCE
5
MAINTENANCE HANDSET BATTERY
Remove
NOTE: Do not remove a battery until you
are ready to install the replacement.
Always fit a Land Rover STC4080 or a
Panasonic CR2032 replacement battery.
1.Unlock the vehicle and disarm the alarm system.
2.Turn the ignition switch to position’II’, then turn
to position’0’and remove the key.
3.Carefully prise the handset apart, starting from
the keyring end. Avoid damaging the seal
between the two halves of the case.
CAUTION: Do not allow moisture to get
inside the handset.
4.Slide the battery out of its clip, taking care to
avoid touching the circuit board or the contact
surfaces of the clip.
5.Press and hold one of the buttons for at least 5
seconds to drain any residual power from the
handset.
Refit
6.Fit the new battery, ensuring that correct polarity
is maintained (+ve side facing up). Finger marks
will adversely affect battery life. Avoid touching
the flat surfaces of the battery, and wipe clean
before fitment.
7.Reassemble the two halves of the handset.
Operate the Padlock symbol button at least 4
times within range of the vehicle to
resynchronise the hanset.HEADLAMP ALIGNMENT
1.Check alignment of headlamps.See
ELECTRICAL, Adjustment.
ProCarManuals.com

ENGINE
27
DESCRIPTION AND OPERATION Camshaft
The camshaft is machined from cast steel and is located between the cylinder head and the camshaft carrier and
the six bearing journals are line bored between the two components to form a matched pair. The machined
camshaft has 15 lobes. Ten lobes operate the inlet and exhaust valves through hydraulic lash adjusters and finger
followers which are located below the camshaft. Five larger lobes activate the injector rockers which are located
above the camshaft on the rocker shaft and are used to generate fuel pressure in the EUI injectors.
The camshaft sprocket is driven via a Duplex chain connected to the crankshaft sprocket at a speed ratio of 2:1.
The camshaft sprocket is fixed to the front end of the camshaft by three bolts.
Camshaft lubrication is by splash and channel fed via pressurised oil flowing through galleries in the cylinder head.
Rocker shaft and rocker arms
Type A - Non EU3 Models - Engine Serial No. Prefixes 10P to 14P
Type B - EU3 Models - Engine Serial No. Prefixes 15P to 19p
1.Rocker arm adjusting screw
2.Rocker shaft
3.Rocker arm
4.EUI pin and roller assembly
5.Roller pin retention slug6.Camshaft lobe
7.Injector spring
8.Injector push-rod
9.Adjusting nut
The hollow rocker shaft is located in the camshaft carrier in six fixed mountings which sit above the camshaft. Six
bolts are used to lock the rocker shaft to the camshaft carrier. The front rocker shaft bearing has a ring dowel
located at the front rocker shaft mounting of the camshaft carrier for rocker shaft alignment. Two circlips hold each
rocker arm in position at the relevant positions on the rocker shaft.
CAUTION: The rocker shaft from a pre EU3 engine must not be fitted to an EU3 engine. This is
because the stroke of the EU3 injector has increased which requires the rocker to articulate over a
larger angle.
The camshaft end of each rocker arm features a roller which is free to rotate about a pin which passes through
two webs in the rocker arm, the roller pins are held in place by an interference fit retention slug passing through a
hole in the front web of each rocker arm.
To correctly function against the higher loads of the EU3 engine the geometry of the contact between the injector
pushrod and rocker arm adjusting screw has been modified. Both designs of adjusting screw are separately
available, with the EU3 version identified by an engraved dimple on the slotted end.
Rocker shaft and rocker arm lubrication is by splash and channel fed via pressurised oil flowing through galleries
in the cylinder head and through the rocker shaft.
ProCarManuals.com

12ENGINE
24
OVERHAUL Inspection
CAUTION: Inspection/overhaul procedures
for the oil pump are limited to carrying out
dimensional checks. In the event of wear
or damage being found, a replacement pump and
stiffener plate assembly must be fitted.
Oil pump
1.Remove and discard 5 screws securing cover to
oil pump, remove cover.
2.Using a felt tipped pen, make suitable alignment
marks between inner and outer rotors and pump
body.
3.Remove inner and outer rotors.
4.Check rotors, cover and pump body for signs of
scoring and wear.
5.Fit rotors ensuring that reference marks are
aligned and identification mark on inner rotor is
facing outwards.
6.Using feeler gauges, check pump body to outer
rotor clearance:
Pump body to outer rotor clearance =0.295
to 0.375 mm (0.012 to 0.015 in)
7.Using feeler gauges, check clearance of inner to
outer rotor in 2 positions, both clearances must
be within limit given:
Inner to outer rotor clearance =0.13 mm (0.05
in)
ProCarManuals.com

12ENGINE
30
OVERHAUL
22.Fit oil seal guide, from seal kit, over end of
crankshaft.
23.Fit new oil seal into timing cover using
LRT-12-156.
CAUTION: Oil seal must be fitted dry.
24.RemoveLRT-12-156and oil seal guide.
25.Fit crankshaft pulley, fit crankshaft pulley bolt.
26.FitLRT-51-003to crankshaft pulley and secure
with 2 bolts.
27.Using assistance, restrain engine and using a
torque multiplier, tighten crankshaft bolt to460
Nm (340 lbf.ft).
WARNING: DUE TO THE HIGH TORQUE
LOADING REQUIRED, IT IS ESSENTIAL
THAT ENGINE IS ADEQUATELY
RESTRAINED.
28.RemoveLRT-51-003.
29.Position damper to crankshaft pulley, fit 3 bolts
and tighten to80 Nm (60 lbf.ft).
30.Fit sump gasket.See this Section.
31.Fit cylinder head gasket.See this Section.BEARINGS - CONNECTING RODS
Service repair no - 12.17.16.01
Remove
1.Remove oil pump.See this Section.
2.Mark cylinder reference number on each
connecting rod big-end bearing cap.
3.Make suitable alignment marks between each
big-end bearing cap and connecting rod.
CAUTION: Due to the’fracture split’
method of manufacturing connecting rods
and bearing caps, incorrect fitting of cap
to connecting rod will damage mating faces and
necessitate replacement of connecting rod
assembly.
4.Rotate crankshaft clockwise until No. 1 big-end
is at BDC.
5.Remove and discard 2 bolts securing No. 1
big-end bearing cap.
6.Remove bearing cap, remove and discard
big-end bearing shell.
7.Push connecting rod up cylinder bore until rod is
clear of crankshaft journal.
CAUTION: Ensure that connecting rod
does not contact cylinder bore or oil squirt
jet and piston does not contact the valves
or EUI’s if the cylinder head is fitted.
ProCarManuals.com

ENGINE
33
OVERHAUL Cylinder bores - Inspection
1.Check cylinder bores for scoring.
2.Measure cylinder bore wear and ovality at a
point 70 mm (2.75 in) from top of each cylinder
bore:
Cylinder bore diameter =84.460 to 84.442 mm
(3.325 to 3.324 in)
CAUTION: Measurement must be taken
from side to side and front to rear of bore:
CAUTION: Cylinder bore diameter and
ovality must be within limits given above,
no reboring, honing or glaze busting of
cylinder bores is permissible; cylinder block must
be replaced if bores are worn or excessively
scored.
Pistons and connecting rods - Inspection
1.Check each piston for cracks, burning and
damage.
2.Check connecting rods for alignment.
CAUTION: Do not attempt to straighten
misaligned connecting rods.
3.Ensure small-end oil feed holes in connecting
rods are clear.
4.Measure and record diameter of each piston at
right angles to gudgeon pin axis and 46 mm
(1.81 in) from bottom of skirt:
Piston diameter =84.262 mm±0.009 mm
(3.317 in±0.0003 in)
CAUTION: Measurement point must be on
the graphited area of the piston.
ProCarManuals.com

12ENGINE
36
OVERHAUL 9.Check that the cut-out in piston skirt is
positioned above the oil squirt jet.
10.Repeat for other pistons in turn ensuring that
pistons and connecting rods are fitted in cylinder
bores from which they were removed.
11.Fit connecting rod bearings.See this Section.
CAUTION: If new pistons, connecting rods
or crankshaft have been fitted, it will be
necessary to select correct thickness of
cylinder head gasket.See this Section.CRANKSHAFT
Service repair no - 12.21.33.01
Remove
1.Remove timing chain and sprockets.See this
Section.
2.Remove crankshaft rear oil seal.See this
Section.
3.Remove connecting rod bearings.See this
Section.
4.Check that cylinder reference number is on each
main bearing cap. Make suitable alignment
marks between each main bearing cap and
cylinder block.
5.Starting at No. 3 main bearing cap and working
outwards, progressively loosen, then remove 2
bolts securing each cap. Discard main bearing
cap bolts.
ProCarManuals.com

MANIFOLD AND EXHAUST SYSTEM
3
DESCRIPTION AND OPERATION Front pipe assembly
The front pipe is of welded and fabricated tubular construction. The front pipe is connected to a flange on the
turbocharger and secured with three flanged nuts and sealed with a metal laminated gasket. The front pipe
incorporates a flexible pipe near the connection with the turbocharger and terminates in a flanged connection with
the intermediate pipe.
The flexible pipe is formed into a concertina shape with woven metal strands around its outer diameter. The
flexible pipe allows for ease of exhaust system alignment and also absorbs engine vibration. The woven metal
strands also increase the longevity of the flexible pipe.
The front pipe is attached via a bracket and a mounting rubber to the chassis. The mounting rubber allows ease of
alignment and vibration absorption.
Intermediate pipe and silencer
The intermediate pipe is of welded and fabricated tubular construction. It connects at its forward end to the front
pipe flange. Two captive studs on the intermediate pipe flange allow for attachment to the front pipe with locknuts.
The rear section of intermediate pipe connects to the tail pipe assembly via a flanged joint, sealed with a metal
gasket and secured with locknuts and studs.
The forward and rear sections are joined by a silencer. The silencer is fabricated from stainless steel sheet to form
the body of the silencer. An end plate closes each end of the silencer and is attached to the body with seam joints.
Perforated baffle tubes, inside the silencer, are connected to the inlet and outlet pipes on each end plate. Internal
baffle plates support the baffle tubes and, together with a stainless steel fibre packing, absorb combustion noise
as the exhaust gases pass through the silencer.
The intermediate pipe is attached by two brackets, positioned at each end of the silencer, and two mounting
rubbers to the chassis. The mounting rubber allows for ease of alignment and vibration absorption.
Tail pipe assembly
The tail pipe is of welded and fabricated construction. The tail pipe connects to the intermediate pipe with a
flanged joint secured with locknuts and sealed with a metal gasket. The pipe is shaped to locate above the rear
axle allowing clearance for axle articulation. The pipe is also curved to clear the left hand side of the fuel tank
which has a reflective shield to protect the tank from heat generated from the pipe.
A fabricated silencer is located at the rear of the tail pipe. The silencer is circular in section and is constructed from
stainless steel sheet. A baffle tube is located inside the silencer and the space around the baffle tube is packed
with a stainless steel fibre. The holes in the baffle tube allow the packing to further reduce combustion noise from
the engine. The tail pipe from the silencer is curved downwards at the rear of the vehicle and directs exhaust
gases towards the ground. The curved pipe allows the exhaust gases to be dissipated by the airflow under the
vehicle and prevents the gases from being drawn behind the vehicle.
The tail pipe is attached by a bracket, positioned forward of the silencer, and a mounting rubber to the chassis.
The mounting rubber allows ease of alignment and vibration absorption.
ProCarManuals.com

CLUTCH
1
REPAIR CLUTCH ASSEMBLY
Service repair no - 33.10.01.01
Remove
1.Remove gearbox assembly.See MANUAL
GEARBOX, Repair.
2.Restrain flywheel.
3.Working in sequence, loosen 6 nuts securing
clutch cover to flywheel.
4.Remove clutch cover and clutch plate.
Refit
5.Clean clutch cover and flywheel mating faces
and spigot bush in end of crankshaft.
6.Position clutch drive plate to flywheel with
’gearbox side’ facing towards gearbox.
7.PositionLRT-12-152alignment tool through
drive plate into spigot bearing in crankshaft.8.Fit clutch cover and locate on dowels.
9.Position clutch cover nuts and tighten in diagonal
sequence to25 Nm (18 lbf.ft).
10.Fit gearbox assembly.See MANUAL
GEARBOX, Repair.
ProCarManuals.com

51REAR AXLE AND FINAL DRIVE
2
OVERHAUL
CAUTION: To prevent permanent damage
to the gear carrier case, it must not be
over-stretched. Each flat on the turnbuckle
is numbered to enable a check to be made on the
amount turned. The maximum stretch permitted is
0,30 mm, equivalent to three flats.
15.Ease off adjuster and remove spreader.
Using axle compressor LRT-51-503
16.Place tool on to differential casing, as illustrated,
with weld seam uppermost. Ensure that plates
rest squarely on differential machined surface
and end bars butt against edges of casing.
17.Tighten adjusting nuts by hand only, until all
slack is taken up.
18.Continue to tighten both nuts alternately with a
spanner, one flat at a time, to a maximum of
three flats.
19.Carefully lever-out differential assembly.
Dismantle differential
20.Add alignment marks between crown wheel and
differential case for reassembly purposes, then
remove fixings and withdraw crown wheel.
21.Note alignment markings on two differential
casings to ensure correct refitting, then remove
fixings.
22.Lift off upper case.
23.Withdraw upper differential wheel and thrust
washer.
24.Lift out cross-shaft and pinions.
ProCarManuals.com