check engine LAND ROVER DEFENDER 1999 Workshop Manual

01INTRODUCTION
6
INFORMATION 3.Position an axle stand under right hand axle
tube, carefully lower jack until axle sits securely
on both axle stands, remove trolley jack.
4.Before commencing work on underside of
vehicle re-check security of vehicle on stands.
5.Reverse procedure when removing vehicle from
stands.
Raise rear of vehicle
1.Position cup of hydraulic arm under differential
casing.
2.Raise vehicle to enable axle stands to be
installed under left and right hand axle tubes.
3.Lower jack until axle sits securely on axle
stands, remove trolley jack.
4.Before commencing work on underside of
vehicle re-check security of vehicle on stands.
5.Reverse procedure when removing vehicle from
stands.
HYDRAULIC VEHICLE RAMP (FOUR POST)
Use only a’drive on’type ramp which supports vehicle
on its road wheels. If a’wheel-free’condition is
required, use a’drive on’ramp incorporating a
’wheel-free’system providing support beneath axle
casings. Alternatively, place vehicle on a firm, flat floor
and support on axle stands.
TWO POST VEHICLE RAMPS
The manufacturer of LAND ROVER VEHICLES
DOES NOT recommend using ’Two Post’ ramps
that employ four adjustable support arms. These
are NOT considered safe for Land Rover vehicles.
If vehicle is installed on a Two Post ramp
responsibility for safety of vehicle and personnel
performing service operations is in the hands of
the Service Provider.DYNAMOMETER TESTING
The front and rear axles cannot be driven
independently.
WARNING: DO NOT attempt to drive
individual wheels with vehicle supported
on floor jacks or stands.
Four wheel dynamometers
Provided that front and rear dynamometer rollers are
rotating at identical speeds and that normal workshop
safety standards are applied, there is no speed
restriction during testing except any that may apply to
the tyres.
Two wheel dynamometers
IMPORTANT: Use a four wheel dynamometer for
brake testing if possible.
If brake testing on a single axle rig is necessary it
must be carried out with propeller shaft to rear axle
removed, AND neutral selected in BOTH main
gearbox and transfer gearbox. When checking brakes,
run engine at idle speed to maintain servo vacuum.
If checking engine performance, the transfer box must
be in high range and propeller shaft to stationary axle
must be removed.
ProCarManuals.com

GENERAL FITTING REMINDERS
1
INFORMATION GENERAL FITTING REMINDERS
WORKSHOP SAFETY IS YOUR RESPONSIBILITY!
The suggestions, cautions and warnings in the
section are intended to serve as reminders for
trained and experienced mechanics. This manual
is not a definitive guide to automotive mechanics
or workshop safety.
Shop equipment, shop environment, and the use
and disposal of solvents, fluids, and chemicals
are subject to government regulations which are
intended to provide a level of safety. It is your
responsibility to know and comply with such
regulations.
PRECAUTIONS AGAINST DAMAGE
1.Always fit covers to protect fenders before
commencing work in engine compartment.
2.Cover seats and carpets, wear clean overalls
and wash hands or wear gloves before working
inside vehicle.
3.Avoid spilling hydraulic fluid or battery acid on
paint work. Wash off with water immediately if
this occurs. Use Polythene sheets to protect
carpets and seats.
4.Always use a recommended Service Tool where
specified.
5.Protect temporarily exposed screw threads by
replacing nuts or fitting plastic caps.SAFETY PRECAUTIONS
1.Whenever possible, use a lift when working
beneath vehicle, in preference to jacking. Chock
wheels as well as applying parking brake.
WARNING: Do not use a pit when
removing fuel system components.
2.Never rely on a jack alone to support vehicle.
Use axle stands carefully placed at jacking
points to provide rigid support.
3.Ensure that a suitable form of fire extinguisher is
conveniently located.
4.Check that any lifting equipment used has
adequate capacity and is fully serviceable.
5.Disconnect battery.
WARNING: Do not disconnect any pipes in
air conditioning system, unless trained
and instructed to do so. A refrigerant is
used which can cause blindness if allowed to
contact eyes.
6.Ensure that adequate ventilation is provided
when volatile degreasing agents are being used.
7.Do not apply heat in an attempt to free stiff
fixings; as well as causing damage to protective
coatings, there is a risk of damage to electronic
equipment and brake linings from stray heat.
ProCarManuals.com

LUBRICANTS, FLUIDS AND CAPACITIES
3
INFORMATION CAPACITIES
The following capacity figures are approximate and are provided as a guide only.
Capacities (approx.)* Litres Pints
Engine sump oil - Td5 7.20...................................................... 12.67
Extra when refilling after fitting new filter 1.00.......................... 1.76
Manual gearbox 2.38............................................................... 4.19
Transfer gearbox oil 2.30......................................................... 4.00
Front differential 1.70............................................................... 3.00
Rear differential
90 Models 1.70............................................................... 3.00
110 Models 2.26............................................................. 4.00
Power steering box and reservoir LHD 2.90............................ 5.00
Power steering box and reservoir RHD 3.40............................ 6.00
Swivel pin housing oil/grease (each) 0.35................................ 0.60
Fuel tank usable fuel
90 Models 60.00............................................................... 13.20 gall
110 & 130 Models 75.00................................................... 16.50 gall
Cooling system - Td5 13.00....................................................... 22.88
Washer bottle 3,0................................................................... 5.28
NOTE: * All levels must be checked by dipstick or level plugs as applicable.
ANTI-FREEZE
PERCENTAGE CONCENTRATION - 50%
PROTECTION - LOWER TEMPERATURE LIMIT
Complete protection
Vehicle may be driven away immediately from cold,
-33°C (-36°F).
Safe limit protection
Coolant in semi-frozen state. Engine may be started
and driven away after warm-up period, -41°C (-42°
F).
Lower protection
Prevents frost damage to cylinder head, block and
radiator. Thaw out before starting engine, -47°C (-53°
F).
CAUTION: Anti-freeze content must never
be allowed to fall below 50% otherwise
damage to the engine is liable to occur.
Also, anti-freeze content should not exceed 60%
as this will greatly reduce the cooling effect of the
coolant.RECOMMENDED FUEL
Diesel fuel oil, distillate, diesel fuel, automotive gas or
Derv to British standard 2869, Class A1 or A2
Using diesel fuel with a class rating lower than stated
above could seriously impair vehicle performance.
ProCarManuals.com

MAINTENANCE
9
MAINTENANCE INTERCOOLER / COOLING SYSTEM
1.Visually check for any obstructions in the
radiator and intercooler matrix and remove
debris as necessary.
2.Visually check fan blades for damage.
3.Check cooling, intercooler and heating systems
for leaks, hoses and oil pipes for security and
condition.
4.Check accessible hose clips for tightness.
5.Check coolant level, top-up if necessary
Cooling System Top-Up
1.With engine cold, remove expansion tank filler
cap.
2.Top-up with recommended mixture of coolant
until level reaches mark on expansion tank.
3.Fit expansion tank filler cap.
Intercooler Flush
1.Remove intercooler.See FUEL SYSTEM,
Repair.
2.Flush intercooler element using Unicorn
Chemicals’C’Solve following the manufaturers
instructions.
3.Thoroughly dry intercooler ensuring that no trace
of solvent remains in the element.
4.Refit intercooler.See FUEL SYSTEM, Repair.AMBIENT AIR PRESSURE (AAP) SENSOR - Td5
1.Check ambient air pressure sensor for damage.
ProCarManuals.com

10MAINTENANCE
10
MAINTENANCE DOOR LOCKS AND HINGES
Front, rear and tail doors
1.Open each door in turn and lubricate door
hinges and check strap using recommended
lubricant.
2.Lubricate door lock, striker and private lock using
PTFE lubricant. Remove excessive lubricant,
particularly from door striker area, to avoid
customer complaint.
3.Check tightness of accessible door lock and
striker fixings
4.Open and close door to check for smooth,
noise-free operation. Ensure door closes
securely.
5.Check for smooth operation of private lock.
Bonnet
1.With bonnet open, lubricate hinges, striker, lock
and safety catch using a suitable lubricant.ENGINE COOLANT
1.Renew engine coolant.See COOLING
SYSTEM, Adjustment.
ProCarManuals.com

MAINTENANCE
19
MAINTENANCE PAS PIPES AND UNIONS
Check
1.Check PAS pipes for correct, secure routing and
signs of chafing.
2.Check for signs of fluid leakage from PAS pump,
hoses, and hose unions.ENGINE, GEARBOX, TRANSFER BOX AND AXLES
Check
1.Check for oil leaks from engine, gearbox, tansfer
box, and front and rear axles. Pay particular
attention to areas around oil seals.
ProCarManuals.com

MAINTENANCE
23
MAINTENANCE ENGINE AND TRANSMISSION MOUNTINGS
1.Check condition of front LH engine mounting.
Tighten fixings if necessary.See ENGINE ,
Repair.
2.Check condition of front RH engine mounting.
Tighten fixings if necessary.See ENGINE ,
Repair.
3.Check condition of rear LH gearbox mounting.
Tighten fixings if necessary.See ENGINE ,
Repair.
4.Check condition of rear RH gearbox mounting.
Tighten fixings if necessary.See ENGINE ,
Repair.ROAD TEST
There are two purposes for conducting a road test.
Firstly, to ensure the work completed within the
dealership meets the standards required as layed
down by dealership processes. Secondly, for a skilled
technician to assess the general condition of the
vehicle and report any conditions that the customer
should be made aware of.
CAUTION: Two wheel roller tests must not
be carried out. Four wheel roller tests
must be restricted to 3 mph (5 kph).
1.Check for correct operation of starter switch.
Ensure the engine starts in a correct manner.
Leave the engine running.
2.With vehicle stationary, turn steering from lock to
lock. Check for smooth operation and ensure
there is no undue noise from the power steering
pump or drive belt.
3.Depress clutch and select all gears in turn.
Check for smooth notch free engagement.
4.Drive vehicle on a short road test. Check all
vehicle systems for correct operation. Pay
particular attention to:
Engine noise
Gearbox noise
Suspension noise
Body noise
Braking system operation
Gear selection
Engine performance
5.Check for correct operation of all instruments
and warning devices where practical.
6.After road test, carry out a final inspection of the
vehicle on vehicle ramps.
7.Check all underbonnet fluid levels and top-up if
necessary.
ProCarManuals.com

12 - ENGINE
CONTENTS
Page
DESCRIPTION AND OPERATION
TD5 ENGINE 1........................................................................................................
GENERAL 12..........................................................................................................
CYLINDER BLOCK 13............................................................................................
CRANKSHAFT, SUMP AND OIL PUMP 22............................................................
CYLINDER HEAD COMPONENTS 25...................................................................
CAMSHAFT COVER COMPONENTS 30...............................................................
CAMSHAFT TIMING CHAIN COMPONENTS 30...................................................
CYLINDER BLOCK FLOW 32.................................................................................
OIL COOLER / FILTER FLOW 34...........................................................................
CYLINDER HEAD FLOW 36...................................................................................
ADJUSTMENT
ENGINE OIL PRESSURE CHECK 1......................................................................
REPAIR
CAMSHAFT 1.........................................................................................................
PULLEY - CRANKSHAFT 3....................................................................................
OIL SEAL - CRANKSHAFT - REAR 4.....................................................................
BEARING - SPIGOT - CRANKSHAFT 5.................................................................
GASKET - CYLINDER HEAD 6..............................................................................
ROCKER SHAFT ASSEMBLY 11...........................................................................
GASKET - COVER - CAMSHAFT 13......................................................................
ENGINE AND ANCILLARIES 14.............................................................................
MOUNTING - FRONT - LH 19................................................................................
MOUNTING - FRONT - RH 20................................................................................
MOUNTING - GEARBOX - REAR - LH 21..............................................................
MOUNTING - GEARBOX - REAR - RH 22.............................................................
FLYWHEEL 22........................................................................................................
FILTER - OIL 23......................................................................................................
STRAINER - OIL PICK-UP 24.................................................................................
PUMP - OIL 24........................................................................................................
GASKET - ENGINE TO SUMP 26..........................................................................
SWITCH - OIL PRESSURE 28...............................................................................
VALVE - RELIEF - OIL PRESSURE 29..................................................................
COOLER - ENGINE OIL 29....................................................................................
CENTRIFUGE ASSEMBLY 30................................................................................
ROTOR - CENTRIFUGE 32....................................................................................
ProCarManuals.com

ENGINE
1
ADJUSTMENT ENGINE OIL PRESSURE CHECK
Service repair no - 12.90.09.01
Check
1.Remove oil pressure switch.See Repair.
2.Connect pressure check kitLRT-12-052C
adaptor and gauge to oil pressure switch
position on oil cooler.
3.Check and if necessary, top-up engine oil.
4.Run engine at idle speed and check that oil
pressure is within limits given.
5.Switch off ignition.
6.Remove oil pressure check kitLRT-12-052C.
7.Clean oil spillage.
8.Fit oil pressure switch.See Repair.
Adjust
1.If engine oil pressure is not within specified
limits, check condition of oil pump and/or main
and connecting rod bearings.
ProCarManuals.com

ENGINE
1
REPAIR CAMSHAFT
Service repair no - 12.13.02
Remove
1.Remove cylinder head gasket.See this
Section.
2.Note the gasket thickness indicator and ensure
the same thickness gasket is used on refitment
of cylinder head.
3.Disconnect multiplug from injector units and
remove harness from camshaft carrier.
4.Remove and discard multiplug’O’ring.
5.Loosen lock nuts and fully retract rocker
adjusting screws.
6.Progressively loosen then remove and discard 6
bolts securing rocker shaft, remove shaft.
7.Using sequence shown, progressively loosen
then remove 13 bolts securing camshaft carrier
to cylinder head.
8.Gently tap the camshaft carrier upwards to break
the sealant bond and remove carrier noting it is
located by 2 dowels.
9.Remove camshaft.
10.Remove and discard camshaft rear oil seal.
11.Remove and discard lock nuts and rocker
adjusting screws.
12.Check bearing surfaces in cylinder head and
camshaft carrier for signs of scoring and wear.
ProCarManuals.com