display LAND ROVER DEFENDER 1999 Workshop Manual

01INTRODUCTION
10
INFORMATION CROSS REFERENCE OF EMISSION SYSTEM
TERMINOLOGY
NEW TERM (ACRONYM)
Accelerator pedal (AP).................................................
Air cleaner (ACL)..........................................................
Air conditioning (A/C)...................................................
Battery positive voltage (B+)........................................
Closed loop (CL)..........................................................
Closed throttle position (CTP)......................................
Canister purge valve (CANPV)....................................
Data link connector (DLC)...........................................
Diagnostic trouble code (DTC).....................................
Distributor ignition (DI).................................................
Engine control module (ECM)......................................
Engine coolant level (ECL)...........................................
Engine coolant temperature (ECT)..............................
Engine speed (RPM)....................................................
Evaporative emission system (EVAP)..........................
Engine fuel temperature sensor (EFTS)......................
4th gear, 3rd gear etc. (4GR, 3GR)..............................
Fuel pump (FP)............................................................
Fan control module (FCM)...........................................
Generator (GEN)..........................................................
Ground (GND)..............................................................
Heated oxygen sensor (H02S)....................................
Idle air control (IAC)......................................................
Idle air control valve (IACV).........................................
Ignition control module (ICM).......................................
Intake air temperature (IAT).........................................
Manifold vacuum zone (MVZ)......................................
Mass air flow sensor (MAF).........................................
Open loop (OL)............................................................
Relay module (RM)......................................................
Solid state relay module (SSRM).................................
Three way catalytic converter (TWC)..........................
Throttle body (TB)........................................................
Throttle position sensor (TP)........................................
Transmission range (TR)..............................................
Wide open throttle (WOT)............................................OLD TERM (ACRONYM)
Throttle pedal (-)..........................................................
Air cleaner (-)...............................................................
Air conditioning (AC)....................................................
Battery plus, bat +, bat feed (B+).................................
Closed loop (-).............................................................
Closed throttle, idle position (-)....................................
Charcoal canister purge valve (-).................................
Serial link (-)................................................................
Fault code (-)...............................................................
Electronic ignition (-)....................................................
Electronic control unit (ECU)........................................
Coolant level (-)...........................................................
Coolant temperature (temp).........................................
Coolant temperature thermistor (-)..............................
Engine speed (rev/min)................................................
Evaporative loss system (ELC)...................................
Fuel temperature thermistor (-)....................................
Fourth gear, 3rd gear (-)..............................................
Fuel pump (-)...............................................................
Condenser fan timer (-)................................................
Alternator (-)................................................................
Ground, earth (B-)........................................................
Lambda (02) sensor (-)................................................
Idle speed control (ISC)................................................
Stepper motor (-).........................................................
Ignition module (-)........................................................
Intake temperature/ambient temperature (-)................
Manifold depression, vacuum (-).................................
Air flow meter (-)..........................................................
Fault code display unit (-)............................................
Open loop (-)...............................................................
Relay (-).......................................................................
Control unit (-)..............................................................
Catalyst, catalytic converter (CAT)..............................
Throttle housing (-)......................................................
Transmission gear (-)...................................................
Full throttle, wide open throttle (WOT).........................
ProCarManuals.com

86ELECTRICAL
8
DESCRIPTION AND OPERATION Visual and Audible Warnings
Audible and visual warnings are dependant on market legislation. The hazard warning lamps are controlled by two
outputs from the anti-theft alarm ECU; one for the LH lamps and one for the RH lamps. To illuminate the warning
lamps the output from the ECU is at battery voltage. When the lamps are off, the output is driven to earth.
When the alarm is armed the hazard warning lamps will flash three times to indicate that the system is active.
When the alarm is triggered the sounder will operate in either a pulsed or continuous tone (dependant on market
legislation) and the hazard warning lamps will flash at 0.5 second on/off intervals for 30 seconds. The alarm
system can be triggered for up to three times in any one alarm armed cycle. When the alarm system is disarmed
confirmation will be by one single flash of the hazard warning lamps for 0.3 seconds.
If the hazard warning lamps are active when an alarm trigger is active or the alarm is armed, the visual alarm
active visual warning using the hazard warning lamps will be cancelled.
In addition to the visual and audible warnings, the security LED in the instrument pack also displays alarm system
status information.
ProCarManuals.com

86ELECTRICAL
10
DESCRIPTION AND OPERATION Remote Handset
The remote handset is a separate unit from the vehicle key and is used to arm and disarm the alarm system. The
handset comprises two buttons; lock and unlock. The handset contains a battery (CR3032) and a printed circuit
board containing the circuitry to generate the RF signals.
NOTE: In selected markets, the vehicle key, when used in the drivers door key barrel switch, will
not disarm the alarm system.
The remote handset RF code consists of two parts. One part is a fixed code that is unique to the handset and the
second part is a rolling code which changes in accordance with a predetermined pattern. The anti-theft alarm ECU
can store the codes of up to four different remote handsets at any one time.
If the remote handset battery falls below a predetermined level, the handset will transmit an additional RF signal
code to the anti-theft alarm ECU when either button is depressed. The security LED will display this as two rapid
flashes every 0.5 seconds to visually display the low handset battery condition. This will continue for the 10
second confirmation period or until the ignition is switched on.
Resynchronisation of Remote Handset
If either the remote handset battery or the vehicle battery is removed or disconnected, the rolling part the handset
code is lost and the handset(s) need to be resynchronised to the anti-theft alarm ECU. The resynchronisation
procedure is as follows:
Disconnect the vehicle battery.
Wait for 30 seconds for residual current to dissipate.
Reconnect the vehicle battery.
Carefully prise the remote handset apart and remove the battery. Avoid unnecessary handling of the battery.
With the battery removed, press either the lock or unlock button several times to remove residual current from
the circuitry.
Check the handset battery with a voltmeter. If the battery voltage is less than 2.7 volts, replace the battery.
Ensure that the battery contact surfaces are clean and replace the battery in the handset clip with the + symbol
uppermost. Put the two halves of the handset case back together.
DO NOT press any buttons.
With the handset within range of the vehicle, press the lock button four times in quick succession. The
anti-theft alarm ECU will respond by locking the vehicle.
Press the unlock button once to complete the resynchronisation procedure.
ProCarManuals.com

86ELECTRICAL
16
DESCRIPTION AND OPERATION CDL Using the Key
The driver and the passenger front doors are fitted with key barrel locks. Using the vehicle key in the passenger
door will only lock or unlock that door. Using the key in the drivers door will operate the CDL system and lock or
unlock all doors.
NOTE: The passenger door key barrel is connected to the door latch and has no electrical input to
the anti-theft alarm ECU. The driver door key barrel is also connected to the door latch and its
operation is monitored by the ECU only via the latch motor and the two wires connected to it.
When the vehicle is locked using the key in the drivers door, only CDL and perimetric protection is invoked.
Volumetric protection and active immobilisation is not initiated.
CDL Using the Remote Handset
The remote handset has two buttons; lock and unlock. A single press on the lock button will lock all doors and
invoke perimetric and volumetric protection and active immobilisation. Remote locking is inhibited if the
transponder coil senses that the key is in the ignition switch.
When the vehicle is locked, a single press of the unlock button will unlock all doors and disable perimetric and
volumetric protection. Immobilisation is only disabled using the transponder coil and the remote handset or the
EKA procedure.
Security LED
In addition to the alarm system status indications, the security LED also displays CDL system status.
The system confirms that the drivers door is open by illuminating the LED for the 10 second confirmation period. If
any other door or the bonnet is open, the LED remains unlit for the 10 second confirmation period. After the 10
second confirmation period the LED reverts to the slow flash deterrent mode if the alarm is armed.
ProCarManuals.com