length LAND ROVER DISCOVERY 1995 Service Repair Manual

GENERAL SPECIFICATION DATA
1
INFORMATION ENGINE 3.9 V8i
Type V8i.................................................................................
Number of cylinders Eight, two banks of four.........................................................
Bore 94,00 mm.................................................................................
Stroke 71,12 mm...............................................................................
Capacity 3950 cc...........................................................................
Compression ratio 8.13:1 or 9.35:1............................................................
Valve operation Overhead by push-rod................................................................
Maximum power - 8.13:1 127kW at 4550 rev/min............................
- 9.35:1 134kW at 4750 rev/min............................
Crankshaft
Main journal diameter 58,409-58,422 mm.......................................................
Minimum regrind diameter 57,393-57,406 mm...............................................
Crankpin journal diameter 50,800-50,812 mm................................................
Minimum regrind diameter 49,784-49,797 mm...............................................
Crankshaft end thrust/(end float) Taken on thrust washers of centre main bearing......................................
0,10-0,20 mm
Main bearings
Number and material 5, Lead-indium........................................................
Diametrical clearance 0,010-0,048 mm.......................................................
Undersize bearing shells 0,254 mm, 0,508 mm..................................................
Connecting rods
Type Horizontally split big-end, plain small-end.................................................................................
Length between centres 143,81-143,71 mm...................................................
Big-end bearings
Type and material Lead-indium............................................................
Diametrical clearance 0,015-0,055 mm.......................................................
End-float crankpin 0,15-0,36mm............................................................
Undersize bearing shells 0,254 mm, 0,508 mm..................................................
Piston pins
Length 72,67-72,79 mm..............................................................................
Diameter 22,215-22,220 mm..........................................................................
Fit-in connecting rod Press fit.........................................................
Clearance in piston 0,002-0,007 mm..........................................................

04GENERAL SPECIFICATION DATA
2
INFORMATION Pistons
Clearance in bore, measured at bottom
of skirt at right angles to piston pin 0,018-0,041 mm...................................
Piston rings
Number of compression rings 2..........................................
Number of control rings 1....................................................
No 1 compression ring Molybdenum barrel faced.....................................................
No 2 compression ring Tapered and marked 'T' or 'TOP'.....................................................
Width of compression rings 1,478-1,49 mm..............................................
Compression ring gap 0,40-0,65 mm......................................................
Oil control ring width 3,0 mm.........................................................
Oil control ring rail gap 0,38-1,40 mm.....................................................
Camshaft
Location Central...........................................................................
Bearings Tin - aluminium...........................................................................
Number of bearings 5..........................................................
Drive Chain 9,52 mm pitch x 54 pitches..................................................................................
TappetsHydraulic-self-adjusting ...........................................................................
Valves
Length: Inlet 116,59-117,35 mm..................................
Exhaust 116,59-117,35 mm...........................
Seat angle: Inlet 45°to 45 1/2° ..................................
Exhaust 45°to 45 1/2° ...........................
Head diameter: Inlet 39,75-40,00 mm..................................
Exhaust 34,226-34,480 mm...........................
Stem diameter: Inlet 8,664-8,679 mm..................................
Exhaust 8,651-8,666 mm...........................
Stem to guide clearance: Inlet 0,025-0,066 mm..................................
Exhaust 0,038-0,078 mm...........................
Valve lift (Inlet and Exhaust) 9,49 mm............................................
Valve spring length fitted 40,4 mm at pressure of 29,5 kg..................................................
Lubrication
System type Wet sump, pressure fed.....................................................................
Oil pump type Eccentric rotor...................................................................
Oil pressure 2.75 bar (40 lb/in
2) at 2500 rev/min with engine at ......................................................................
running temperature
Oil filter-internal Wire screen, pump intake filter.................................................................
Oil filter-external Full flow, self-contained cartridge...............................................................

GENERAL SPECIFICATION DATA
3
INFORMATION ENGINE 4.0 V8
Type 4.0 litre V8.................................................................................
Number of cylinders Eight, two banks of four.........................................................
Bore 94.00 mm................................................................................. 3.70 in
Stroke 71.12 mm............................................................................... 2.80 in
Capacity 3950 cm
3........................................................................... 241 cu in
Valve operation Overhead by push-rod................................................................
High Compression Low Compression
Compression ratio 9.35:1............................................................ 8.2:1
Valve operation Overhead by push-rod................................................................
Maximum power: 9.35:1 140kW at 4750 rev/min..............................
8.2:1 132kW at 4750 rev/min................................
Crankshaft
Main journal diameter 63.500 - 63.487 mm....................................................... 2.50 - 2.4995 in
Crankpin journal diameter 55.513 - 55.500 mm................................................ 2.1855 - 2.1850 in
Crankshaft end thrust/end float Taken on thrust washers of centre main bearing........................................
0.10 - 0.20 mm 0.004 - 0.008 in
Main bearings
Number and type 5, Vandervell shells..............................................................
Material Lead bronze with lead-indium overlay............................................................................
Diametrical clearance 0.015 - 0.060 mm....................................................... 0.0006 - 0.0024 in
Connecting rods
Type Horizontally split big-end, plain small-end.................................................................................
Length between centres 155.12 - 155.22 mm................................................... 6.1071 - 6.1110 in
Big-end bearings
Type and material Vandervell VP3 Lead bronze with lead-indium overlay............................................................
Diametrical clearance 0.015 - 0.016 mm....................................................... 0.0006 - 0.0024 in
Piston pins
Length 60.00 - 60.50 mm.............................................................................. 2.3622 - 2.3819 in
Diameter 23.995 - 24.000 mm.......................................................................... 0.9447 - 0.9449 in
Fit-in connecting rod Press fit.........................................................
Clearance in piston 0.015 - 0.006 mm.......................................................... 0.0006 - 0.0002 in
Pistons
Clearance in bore, measured at bottom
of skirt at right angles to piston pin 0.020 - 0.050 mm................................... 0.0008 - 0.0020 in

04GENERAL SPECIFICATION DATA
4
INFORMATION Piston rings
Number of compression rings 2..........................................
Number of control rings 1....................................................
No 1 compression ring Nitrided steel barrel faced.....................................................
No 2 compression ring Tapered spherical barrel marked 'TOP'.....................................................
Width of compression rings 1.478 - 1.49 mm.............................................. 0.0582 - 0.0587 in
(Top) 1.21 - 1.23 mm................................ 0.0476 - 0.0484 in
Compression ring gap 0.40-0.65 mm...................................................... 0.0157 - 0.0256 in
(Top) 0.3 - 0.5 mm................................ 0.0118 - 0.0197 in
Oil control ring type Aclonoform..........................................................
Oil control ring width 3.0 mm......................................................... 0.1181 in
Oil control ring rail gap 0.38-1.40 mm..................................................... 0.0150 - 0.0551 in
Camshaft
Location Central...........................................................................
Bearings Non serviceable...........................................................................
Number of bearings 5..........................................................
Drive Chain 9.52 mm pitch x 54 pitches..................................................................................
Camshaft End Float 0.076 - 0.355 mm......................................................... 0.003 - 0.014 in
TappetsHydraulic self-adjusting ...........................................................................
Valves
Length: Inlet 116.59 - 117.35 mm.................................. 4.590 - 4.620 in
Exhaust 116.59 - 117.35 mm........................... 4.590 - 4.620 in
Seat angle: Inlet 46°-46°25' ..................................
Exhaust 46°-46°25' ...........................
Head diameter: Inlet 39.75 - 40.00 mm.................................. 1.565 - 1.575 in
Exhaust 34.227 - 34.48 mm........................... 1.3475 - 1.3575 in
Stem diameter: Inlet 8.664 - 8.679 mm.................................. 0.3411 - 0.3417 in
Exhaust 8.651 - 8.666 mm........................... 0.3406 - 0.3412 in
Stem to guide clearance: Inlet 0.025 - 0.066 mm.................................. 0.0010 - 0.0026 in
Exhaust 0.038 - 0.078 mm........................... 0.0015 - 0.0031 in
Valve lift (Inlet and Exhaust) 9.94 mm............................................ 0.3913 in
Valve spring length fitted 40.4 mm (1.59 in) at pressure of 29.5 kg (65 lb)..................................................
Lubrication
System type Wet sump, pressure fed.....................................................................
Oil pump type Rotor...................................................................
Oil pressure 2.11 to 2.81 kg/cm
2(30 to 40 psi) at 2400 rev/min with ......................................................................
engine warm
Oil filter-internal Wire screen, pump intake filter in sump................................................................
Oil filter-external Full flow, self-contained cartridge...............................................................

GENERAL SPECIFICATION DATA
13
INFORMATION AIR CONDITIONING
System Nippon Denso.............................................................................
Compressor Nippon Denso 10 PA 17.....................................................................
Refrigerant R134a.......................................................................
Charge quantity 0.9Kg................................................................
Charge quantity with rear air conditioning 1.15Kg........................
WIPER MOTORS
Tailgate wiper motor
Make/type IMOS (non-serviceable)........................................................................
Running current, wet screen at 20°C ambient 1.0 to 2.8 amps.................
Wiper speed, wet screen at 20°C ambient 37 to 43 cycles per minute.......................
Windscreen wiper motor
Make/type Delco AMR 1514/5........................................................................
Running current (Link disconnected) 1.5 amps at 39 to 45 rev/min (normal speed)...............................
Rotary link speed 60 to 73 rev/min (high speed).............................................................
ELECTRICAL
System 12 volt, negative ground.............................................................................
Battery
Make/type - basic Land Rover Parts and Equipment/Lucas maintenance.............................................................
free 9-plate-YGD 10017
Make/type - heavy duty Land Rover Parts and Equipment/Lucas maintenance....................................................
free 14-plate-YGD 10015
Generator
Manufacturer Magnetti Marelli....................................................................
Type A127i 100amp.................................................................................
Polarity Negative ground.............................................................................
Brush length
New 17 mm.........................................................................
Worn, minimum free protrusion from moulding 5 mm.......
Brush spring pressure flush with moulding 1.3N to 2.7N......................
Regulator voltage 13.6 to 14.4 volts.............................................................
Nominal output
Generator speed 6000 rev/min.....................................................
Control voltage 14 volt........................................................
Amp 100 amp.........................................................................

04GENERAL SPECIFICATION DATA
18
INFORMATION 300 Tdi ENGINE
Type Direct injection, turbocharged, intercooled.................................................................................
Number of cylinders 4.........................................................
Bore 90,47 mm.................................................................................
Stroke 97,00 mm...............................................................................
Capacity 2495 cc...........................................................................
Compression ratio 19.5:1±0.5:1 ............................................................
Valve operation O.H.V. pushrod operated................................................................
Crankshaft
Main bearing journal diameter 63,475 - 63,487 mm..........................................
Regrind dimensions 63,2333 - 63,246 mm.........................................................
Use 0.010 in U/S bearings
Crankpin journal diameter 58,725 - 58,744 mm................................................
Regrind dimensions 58,4708 - 58,48985 mm.........................................................
Use 0.010 in U/S bearings
Crankshaft end thrust Taken on thrust washers at centre main bearing.......................................................
Crankshaft end float 0,05 - 0,15 mm.........................................................
Main bearings
Number and type 5 halved shells with oil grooves..............................................................
Diametrical clearance 0,0792 - 0,0307 mm.......................................................
Connecting rods
Length between centres 175,38 - 175,43 mm...................................................
Diametrical clearance (big-end bearings) 0,025 - 0,075 mm........................
End float on crankpin 0,15 - 0,356 mm.......................................................
Pistons
Type Aluminium alloy, combustion chamber in crown..................................................................................
Graphite coating on sidewalls.
Skirt diametrical clearance
(at right angle to gudgeon pin) 0,025 - 0,05 mm.........................................
Maximum height above combustion face 0,8 mm.........................
Gudgeon pins
Type Floating.................................................................................
Fit in piston Hand push fit.......................................................................
Diameter 30,1564 - 30,1625 mm..........................................................................
Clearance in connecting rod 0,0025 - 0,0163 mm............................................

GENERAL SPECIFICATION DATA
19
INFORMATION Piston rings
Type:
- Top Barrel edge, chrome plated........................................................................
- Second Taper faced..................................................................
- Oil control Expander and rails..............................................................
Gap in bore:
- Top 0,40 - 0,60 mm........................................................................
- Second 0,30 - 0,50 mm..................................................................
- Oil control 0,3 - 0,6 mm..............................................................
Clearance in piston grooves:
- Second 0,050 - 0,085 mm..................................................................
- Oil control 0,050 - 0,085 mm..............................................................
Camshaft
Drive 30 mm wide dry toothed belt.................................................................................
Location Right hand side (thrust side)...........................................................................
End float 0,1 - 0,2 mm...........................................................................
Number of bearings 4..........................................................
Material Steel shell, white metal lined............................................................................
Valves
Tappet clearance:
- Inlet and exhaust 0,20 mm...................................................
Seat angle:
- Inlet 30° .......................................................................
- Exhaust 45° .................................................................
Head diameter:
- Inlet 38,75 - 39,05 mm.......................................................................
- Exhaust 36,35 - 36,65 mm.................................................................
Stem diameter:
- Inlet 7,960 - 7,975 mm.......................................................................
- Exhaust 7,940 - 7,960 mm.................................................................
Valve lift:
- Inlet 9,67 mm.......................................................................
- Exhaust 9,97 mm.................................................................
Cam lift:
- Inlet 6,81 mm.......................................................................
- Exhaust 7,06 mm.................................................................
Valve head stand down
- Inlet 0,81 - 1,09 mm.......................................................................
- Exhaust 0,86 - 1,14 mm.................................................................
Valve springs
Type Single coil.................................................................................
Length, free 46,28 mm......................................................................
Length, under 21 kg load 40,30 mm.................................................

04GENERAL SPECIFICATION DATA
20
INFORMATION Lubrication
System Wet sump, pressure fed.............................................................................
Pressure, engine warm at normal operating speeds 25 - 55lbf/in
2= 1,76 - 3,87Kgf cm2........
Oil pump:
- Type G-rotor integral with front cover.......................................................................
- Drive off crankshaft nose.....................................................................
Oil pressure relief valve Non-adjustable....................................................
Relief valve spring:
- Full length 51,6mm......................................................................
- Compressed length at 7.71Kg load 31mm................................
Oil filter Screw-on disposable canister.............................................................................
Engine oil cooler Combined with coolant radiator and intercooler...............................................................
FUEL SYSTEM - 300 Tdi
Fuel lift pump type Mechanical with hand primer............................................................
Fuel lift pump pressure 42 - 55 kpa at 1800 rpm.....................................................
Fuel filter Paper element in disposable canister..........................................................................
Air cleaner Paper element type........................................................................
COOLING SYSTEM - 300 Tdi
System type Pressurised, spill return, thermostatically controlled.....................................................................
water and anti freeze mixture. Pump assisted thermo
syphon. Coolant radiator combined with oil cooler and
turbo intercooler.
Cooling fan 11 blade axial flow 433 mm diameter. 1.29:1 drive.......................................................................
ratio. Viscous coupling.
Pump type Centrifugal, impellor, belt driven.........................................................................
Thermostat opening 88° .........................................................
Expansion tank cap pressure 15lbf/in
2= 1,06Kgf cm2(system pressure) ...........................................
CLUTCH - 300 Tdi
Type Valeo diaphragm spring.................................................................................
Centre plate diameter 235 mm.......................................................
Facing material Verto F202 grooved.................................................................
Release bearing Ball journal...............................................................

04GENERAL SPECIFICATION DATA
22
INFORMATION ENGINE - Mpi - 2.0 LITRE
Type 20 T4 - 16 valve twin overhead camshaft.................................................................................
Cylinder arrangement 4 in line.......................................................
Bore 84.45 mm.................................................................................
3.325 in
Stroke 89.00 mm...............................................................................
3.504 in
Capacity 1994 cm
3...........................................................................
121.68 in3
Firing order 1-3-4-2.......................................................................
Compression ratio 10 : 1............................................................
Oil pump
Outer rotor to body clearance 0.05 to 0.10 mm..........................................
Inner rotor tip clearance 0.025 to 0.12 mm...................................................
Outer rotor end float 0.03 to 0.08 mm.........................................................
Oil pressure relief valve
Spring free length 42.0 mm.............................................................
Cooling system
Starts to open 82 to 86°C ...................................................................
Thermostat fully open 88°C .......................................................
Open travel A 9 mm...................................................................
Camshaft
Camshaft end-float 0.06 to 0.25 mm...........................................................
Bearing clearance 0.060 to 0.094 mm............................................................
Service limit 0.15 mm.............................................................
Timing belt tensioner
Spring free length 57.5 to 58.5 mm.............................................................
Cylinder head
Longitudinal warp - maximum 0.1 mm.................................
Transverse warp - maximum 0.1 mm...................................
Diagonal warp - maximum 0.1 mm......................................
Cylinder head height 135.0 to 135.1 mm...............................................
Valve springs
Free length 46.25 mm.......................................................................
Fitted length 37.0 mm.....................................................................
Load at fitted length 255±12 N ..........................................................
Load at valve open length 560±22.5 N ................................................

GENERAL SPECIFICATION DATA
23
INFORMATION Valves
Valve stem diameter:
Inlet 7.09 to 7.10 mm.........................................................................
Exhaust 7.07 to 7.09 mm...................................................................
Valve head diameter:
Inlet 31.7 to 31.95 mm.........................................................................
Exhaust 29.2 to 29.43 mm...................................................................
Valve installed height - maximum 43.4 mm....................................
Valve stem to guide clearance:
Inlet 0.04 to 0.06 mm.........................................................................
Service limit 0.09 mm.............................................................
Exhaust 0.06 to 0.07 mm...................................................................
Service limit 0.10 mm.............................................................
Valve guides
Internal diameter - Inlet and Exhaust 7.137 to 7.162 mm...............................
Overall length:
Inlet 48.5 mm.........................................................................
Exhaust 52.9 mm...................................................................
Valve seats
Valve seat angle - Inlet and Exhaust 45° ................................
Valve seat width - Inlet and Exhaust 1.5 to 2.0 mm................................
Valve face angle:
Inlet and Exhaust 45°to 45°15' .............................................................
Crankshaft
End-float 0.03 to 0.2 mm...........................................................................
Thrust washer halves thickness 2.31 to 2.36 mm.......................................
Main journal diameter 54.005 to 54.026 mm.......................................................
Maximum out of round 0.010 mm............................................
Main bearing diametric clearance 0.03 to 0.07 mm....................................
Big-end journal diameter 47.648 to 47.661 mm..................................................
Maximum out of round 0.010 mm............................................
Big-end bearing diametric clearance 0.04 to 0.08 mm................................
Piston rings
New ring to groove clearance:
Top compression 0.06 to 0.09 mm.............................................................
2nd compression 0.05 to 0.07 mm..............................................................
Oil control rails - expander fitted 0.03 to 0.05 mm......................................
Ring fitted gap:
Top compression 0.25 to 0.35 mm.............................................................
2nd compression 0.3 to 0.5 mm..............................................................
Oil control rails 0.38 to 1.14 mm.................................................................
Pistons
Piston diameter:
Grade A 84.409 to 84.422 mm...................................................................
Grade B 84.423 to 84.436 mm...................................................................
Clearance in bore 0.01 to 0.03 mm.............................................................
Cylinder bore
Grade A 84.442 to 84.455 mm...................................................................
Grade B 84.456 to 84.469 mm...................................................................