brake sensor LAND ROVER DISCOVERY 1995 User Guide

19FUEL SYSTEM
6
DESCRIPTION AND OPERATION DESCRIPTION ELECTRONIC DIESEL CONTROL
The Electronic Diesel Control (EDC) 'drive by wire'
system derives its from the replacement of
conventional mechanical controls by electronic
components.
The EDC system supplies the exact amount of fuel to
the engine according to the prevailing engine
operating conditions. To monitor these conditions,
sensors are fitted to the engine to measure engine
parameters. Data from the sensors is received by the
Engine Control Module (ECM) which determines the
exact amount of fuel, injection timing and Exhaust
Gas Recirculation (EGR) required for any running
condition.
Safety and emergency features are built into the
system which protect the engine against overspeed
and overheating damage. In the event of component
failure the system is designed to compensate and
allow emergency start and limp home facilities to
operate. The ECM does this by substituting a default
value for the failed component which may result in a
noticeable loss in power but keeps the engine
running.FUEL SYSTEM COMPONENT LOCATION EDC
1. Vehicle speed sensor
2. No. 4 injector sensor
3. Coolant temperature sensor
4. Boost pressure sensor
5. Electro-pneumatic modulator
6. Airflow sensor
7. Engine speed sensor
8. Brake/clutch switches
9. Injector pump
10. Throttle position sensor
11. Engine control module

19FUEL SYSTEM
8
DESCRIPTION AND OPERATION FUEL SYSTEM LAYOUT EDC
1. Fuel injection pump
2. Fuel temperature sensor
3. Air temperature sensor
4. Water temperature sensor
5. No. 4 injector sensor
6. Air flow sensor
7. Engine speed sensor
8. Boost pressure sensor
9. Vehicle speed sensor
10. Clutch switch
11. Brake switch
12. Throttle position sensor
13. Electro-pneumatic modulator
14. Exhaust gas recirculation (EGR) valve
15. Engine control module (ECM)
16. Diagnostic indicator
A. To turbo
B. To air box.
C. To 'T' piece on brake servo hose position
D. Solenoid operated valve energization timing device.
E. Fuel cut off
F. Actuator current
G. Control collar

19FUEL SYSTEM
10
DESCRIPTION AND OPERATION Vehicle speed sensor
The vehicle speed sensor is located on the transfer
box behind the transmission brake. The unit has a
multirole as the vehicle electronic speedometer
sensor and as a sensor for 'surge damping', (a
function which smooths out engine response to sharp
accelerator movement and reduces vehicle 'bucking').
The sensor is an additional input for engine overheat
protection.
Brake and clutch switches
The brake and clutch switches are located on the
pedal box and serve as safety features to the system.
They return information to the ECM which limits
maximum fuel quantity under braking.
Throttle position sensor
The accelerator pedal is connected directly to a
sensor mounted in the pedal box. Driver demand is
relayed back to the ECM to increase or decrease
injected fuel quantity.
Incorporated in the sensor is a backup idle switch
which the system will default to in the event of sensor
failure.
Boost pressure sensor
The boost pressure sensor is mounted on the
bulkhead. It relays boost pressure information to the
ECM which compensates fuel quantity to reduce
smoke during acceleration.
Electro-pneumatic modulator
The electro-pneumatic modulator is located on the
inner wing just forward of the air cleaner. It regulates
vacuum signals from the source to the EGR valve.
The ECM controls the modulator to open the EGR
valve according to required airflow.Exhaust gas recirculation valve
The EGR valve is located on the engine exhaust
manifold and is controlled by vacuum from the
electro-pneumatic modulator.
Once open the EGR valve directs a quantity of
exhaust gas back into the inlet manifold to be burnt
inside the engine. This reduces NOx (Oxides of
nitrogen) emissions of the engine.
Temperature sensors
Water, Fuel and Air temperature sensors monitor
engine conditions and relay their information back to
the ECM which makes adjustments to injected fuel
quantity, injection timing, EGR and corrections to
measured boost pressure and airflow.

19FUEL SYSTEM
16
REPAIR ENGINE SPEED SENSOR
Service repair no - 18.30.65
Remove
1.Disconnect battery negative lead.
2.Disconnect sensor multi-plug.
3.Place vehicle on ramp and apply handbrake.
4.Raise ramp.
5.Remove sensor retaining nut.
6.Remove sensor from housing.
7.Clean housing mating faces.
Refit
8.Reverse removal procedure.

19FUEL SYSTEM
18
REPAIR BRAKE PEDAL SWITCH
Service repair no - 18.30.66
Remove
1.Disconnect battery negative lead.
2.Disconnect switch wiring Lucars.
3.Loosen rear locknut.
4.Remove front locknut.
5.Remove switch from mounting bracket.
Refit
6.Reverse removal procedure.COOLANT TEMPERATURE SENSOR
Service repair no - 18.30.68
Remove
1.Disconnect battery negative lead.2.Disconnect sensor multi-plug.
3.Remove sensor.
4.Clean off water spillage from sensor area.
Refit
5.Fit a new copper washer.
6.Fit sensor and tighten securely.
7.Refill cooling system.
8.Run engine, check for water leaks around
sensor.

MFI
3
DESCRIPTION AND OPERATION Tune select resistor -
To suit individual market requirements a tune select
resistor is connected across pins 5 and 27 of the
ECM.
It is located adjacent to the ECM, and strapped to the
MFI cable assembly. The value of the resistor is
dependent on the market application:
Red wire, 180 ohms, Australia, Rest of world.
Green wire, 470 Ohms, UK and Europe - non catalyst.
Yellow wire 910 Ohms, Saudi non catalyst.
White wire, 3K9 Ohms, European catalyst
Condenser fans
It should be noted that under high coolant
temperatures, when the engine is switched off, the
condenser fans will be activated and will run for
approximately ten minutes.Vehicle speed sensor
The vehicle speed sensor is located on the side of the
Transfer box adjacent to the parking brake. The
sensor provides road speed data to the ECM. The
ECM in turn detects vehicle movement from the road
speed input and ensures that idle air control mode is
disengaged. Should the vehicle speed sensor fail in
service the ECM idle air control would become erratic.
The sensor also provides road speed data to the
electric speedometer and cruise control ECU.
Inertia fuel shutoff switch
The inertia fuel shutoff switch is a mechanically
operated switch, located on the bulkhead adjacent to
the washer reservoir under bonnet [hood].
The switch is normally closed and is in line with the
fuel pump. In the event of a sudden impact the switch
opens, and disconnects the electrical feed to the fuel
pump. The switch is reset by pressing down the
button.
WARNING: Check the integrity of the fuel
system before the inertia switch is reset.
Relay modules
The two multiport fuel injection relays are located in
the RH footwell area behind the 'A' post panel. The
main relay module is energized via the ECM when the
ignition is switched on and supplies current to the
multiport fuel injection system. The fuel pump relay
module is energized by the ECM which in turn
operates the fuel pump to pressurize the fuel system.

MFI
3
REPAIR IDLE AIR CONTROL VALVE
Service repair no - 19.22.54
Remove
1.Disconnect battery negative lead.
2.Disconnect multi-plug.
3.Unscrew valve from rear plenum chamber.
4.Remove washer.
Refit
5.FitNEWsealing washer.
NOTE: If same idle air control valve is
being refitted clean sealing compounds
from threads. Apply Loctite 241 to threads
of valve before reassembly.
6.Tighten valve to
20 Nm.
7.Reverse removal procedure.VEHICLE SPEED SENSOR
Service repair no - 88.30.14
The vehicle speed sensor is located in the LH side of
the transfer box.
Remove
1.Place vehicle on lift, apply parking brake.
2.Disconnect battery negative lead.
3.Raise lift, disconnect multiplug from vehicle
speed sensor.
4.Remove screw securing sensor to transfer box.
5.Remove vehicle speed sensor
Refit
6.Reverse removal procedure.

CRUISE CONTROL
1
DESCRIPTION AND OPERATION CRUISE CONTROL COMPONENT LOCATIONS -
Tdi AUTO EDC
COMPONENT LOCATION
1. Cruise control unit Under LH dash...................................................
2. Engagement (on/off) switch Dash panel....................................
3. Cruise control switch Steering wheel...............................................
4. Rotary coupler Steering wheel.........................................................
5. Vacuum pump Box section under jack.........................................................
6. Brake/vent switch Brake pedal....................................................
7. Vehicle speed sensor Transfer box behind transmission brake..............................................
8. Neutral lock-out relay Behind RH lower 'A' post trim casing..............................................
9. Actuator RH engine compartment...................................................................

19FUEL SYSTEM
2
DESCRIPTION AND OPERATION CRUISE CONTROL SYSTEM - V8i/Tdi AUTO EDC
Description
The cruise control system consists of
electro-mechanical devices, and comprises of the
following components.
ELECTRONIC CONTROL UNIT (ECU)
The microprocessor based ECU evaluates the signals
provided by the driver controls, brake pedal switch,
clutch pedal switch on manual models, and the
vehicle speed sensor. The ECU activates the vacuum
pump as required. The ECU also has a memory
function for set speed storage.
Driver operated switches
The main cruise control switch is located in the
auxiliary switch panel and activates the cruise control
system. The steering wheel switches provide
'set/accelerate' and 'resume/decelerate' features.
These switches provide the interface between driver
and cruise control system.
Brake pedal switch
The brake pedal switch is located under the lower
dash attached to the brake pedal mounting bracket.
The switch provides for fast disengagement of the
cruise control system and rapid return of the throttle
levers to the idle position when the brake pedal is
applied.
Clutch pedal switch
The clutch pedal switch is located under the lower
dash attached to the clutch pedal mounting bracket.
The switch provides for fast disengagement of the
cruise control system and rapid return of the throttle
levers to the idle position when the clutch pedal is
applied.Vehicle speed sensor
The vehicle speed sensor is located on the side of the
transfer box adjacent to park brake. The sensor
provides road speed data to the ECU. The cruise
control system cannot be engaged until the road
speed exceeds 45 km/h, (28 mph) the system will
automatically disengage at a road speed of 42 km/h
(26 mph).
Vacuum pump
The vacuum pump is energised when the main cruise
control switch is operated, and is actuated by the
steering wheel and brake pedal switches. The pump
provides a vacuum source to the cruise control
actuator. A control valve in the pump provides for
steady increase of road speed or purge of the system
when the brake pedal is applied.
Actuator
The actuator provides the servo mechanism link
between the cruise control system and throttle linkage
and is operated by vacuum from the vacuum pump.
Neutral lockout relay - automatic vehicles
The relay module is located in the right hand side
footwell, accessible by removing the trim casing.
The function of the relay module is to disengage the
cruise control system if neutral, or park, is selected in
the main gearbox, when the system is engaged.
Engine speed trip ECU - Manual vehicles
This unit is located in the right hand side footwell,
accessible by removing the trim casing.
The function of the unit is to disengage cruise control
if engine speed exceeds 5000 rev/min.

MANIFOLD AND EXHAUST SYSTEM
5
REPAIR INLET MANIFOLD GASKET - Mpi
Service repair no - 30.15.08
Remove
1.Disconnect battery negative lead.
2.Position absorbent cloth around fuel pipe to fuel
rail union. Unscrew union to relieve fuel
pressure. Re-tighten union.
CAUTION: Plug connections.
3.Release clip and remove air cleaner to throttle
housing hose.
4.Disconnect stepper motor multiplug.
5.Disconnect throttle potentiometer multiplug.
6.Release throttle cable from abutment bracket.
7.Release throttle cable from cam. Remove
coolant bypass hose.
8.Disconnect fuel temperature sensor multiplug.
9.Release clip and disconnect brake servo hose
from manifold.