brakes LAND ROVER DISCOVERY 1995 User Guide

MAINTENANCE
19
MAINTENANCE
RESET EMISSION MAINTENANCE REMINDER -
USA
The emission maintenance reminder is designed to
activate at 52,500 and 105,000 miles respectively and
will illuminate a 'Service Engine' red warning light in
instrument binnacle.
The emission maintenance reminder must be reset
after required maintenance has been carried out and
a new tamperproof label fitted by a Land Rover of
North America dealer. This emission maintenance
reminder is part of the Emission Control System
Reset
1.The control unit is located in the passenger
footwell.
2.Identify control unit and remove from plug.
3.Remove tamperproof label to reveal access hole
for resetting.
4.Place a thin metallic probe into access hole and
momentarily electrically short between reset pins
inside unit.RECOMMENDED SERVICE ITEMS
Refer Service Schedule sheets for intervals.
Clean sunroof drain tubes, clean and lubricate guide
rails and slides.
Renew the hydraulic brake fluid.
See BRAKES,
Repair, Brake System Bleed
Renew all hydraulic brake fluid, seals, brake servo
filter and flexible hoses.
All working surfaces of the master cylinder and caliper
cylinders should be examined and renewed where
necessary.
ABS vehicles only - renew hydraulic brake fluid and
flexible hoses examine the working surfaces of the
caliper cylinders and renew the seals or cylinders
where necessary.
Air cleaner - When the vehicle is used in dusty or field
conditions or deep wading, frequent attention to the
air cleaner may be required.
ABS vehicles used extensively in arduous off-road
conditions - check the rear wheel road speed sensor
for abrasive wear.

V8i
3
FAULT DIAGNOSIS ENGINE STARTING PROBLEMS
Engine fails to crank in park or neutral (Automatic
Transmission)
1.Is battery in good state of charge?
NO -
See INTRODUCTION, Information,
Jump Starting
YES - Continue.
2.Is automatic transmission inhibitor switch faulty
or gear selection linkage incorrectly adjusted?
YES -
See AUTOMATIC GEARBOX, Repair,
Inhibitor Switch
,
NO -
See Electrical Trouble Shooting
Manual.
If problem is not diagnosed repeat tests, starting
at 1.
Engine fails to crank (Manual Transmission)
1.Is battery in good state of charge?
NO -
See INTRODUCTION, Information,
Jump Starting
YES -See Electrical Trouble Shooting
Manual.
If problem is not diagnosed repeat tests, starting
at 1.
Engine cranks but fails to start
1.Is the cranking speed fast enough (120 rpm)?
NO -
See INTRODUCTION, Information,
Jump Starting
If necessary also.See Electrical Trouble
Shooting Manual.
YES - Continue.
2.Is there combustion in any cylinder?
NO -
See ELECTRICAL, Fault diagnosis,
Lucas Constant Energy Ignition
System - V8i See Electrical Trouble
Shooting Manual.
YES - Continue.
3.Are the fuel supply, tank, pump, ventilation and
emission control systems in correct working
order or the fuel contaminated?
NO -
See FUEL SYSTEM, Repair, Fuel
Filter See FUEL SYSTEM, Repair,
Fuel Tank See FUEL SYSTEM, Repair,
Fuel pump and Sender Unit See
EMISSION CONTROL, Description and
operation, Emission control
If problem is not diagnosed repeat tests, starting
at 2.ENGINE RUNNING PROBLEMS
Engine runs at high speed but will not idle (stops)
Engine idle speed erratic Engine starts but stops
immediately
Engine stalls Engine misfires/hesitation
1.Multiport fuel injection.
See Electrical Trouble
Shooting Manual. See ELECTRICAL, Fault
diagnosis, Lucas Constant Energy Ignition
System - V8i
Check brake vacuum connections.See
BRAKES, Description and operation, Brake
Servo Unit
Check heater/ventilation unit vacuum
connections.
See HEATING AND
VENTILATION, Description and operation,
Heating and Ventilation Unit
If problem is not diagnosed continue.
2.Are HT leads correctly routed and clipped?
NO -
See ELECTRICAL, Repair, Distributor
- V8i
YES - Continue.
3.Is fuel supply, tank, pump, ventilation and
emission control systems in correct working
order or the fuel contaminated?
NO -
See FUEL SYSTEM, Repair, Fuel
Filter See FUEL SYSTEM, Repair,
Fuel Tank See FUEL SYSTEM, Repair,
Fuel Pump and Sender Unit See
EMISSION CONTROL, Description and
operation, Emission Control
If problem is not diagnosed repeat tests, starting
at 1.
Engine lacks power/poor performance
1.Is throttle travel restricted or cable incorrectly
adjusted?
YES - Check thickness of carpets.
See FUEL
SYSTEM, Repair, Throttle Cable See
FUEL SYSTEM, Repair, Accelerator
Pedal
NO - Continue.
2.Are the Ignition and Multiport Fuel Injection
systems in order?
NO -
See Electrical Trouble Shooting
Manual.A1 See ELECTRICAL, Fault
diagnosis, Lucas Constant Energy
Ignition System - V8i See
ELECTRICAL, Repair, Distributor - V8i
YES - Continue.

12ENGINE
4
FAULT DIAGNOSIS 3.Are fuel supply, tank, pump, ventilation and
emission control systems in correct working
order or the fuel contaminated?
NO -
See FUEL SYSTEM, Repair, Fuel
Filter See FUEL SYSTEM, Repair,
Fuel Tank See FUEL SYSTEM, Repair,
Fuel Pump and Sender Unit
YES - Suspect valves held open by hydraulic
tappets due to high oil pressure.
See
Engine Oil Pressure Test
4.Is oil pressure high?
YES - Remove oil filter and cooler adaptor and
check pressure relief valve strainer gauze
for blockage and that the relief valve is
not stuck closed.
See Description and
operation, Description
NO - Carry out cylinder compression tests to
determine condition of head gaskets and
valves.
See Cylinder Compression -
Test
5.Are cylinder compressions satisfactory?
NO -
See Repair, Cylinder Heads - Renew
YES - Check brake vacuum connections.See
BRAKES, Description and operation,
Brake Servo Unit
Check heater/ventilation unit vacuum connections.
See HEATING AND VENTILATION, Description and
operation, Heating and Ventilation Unit
If problem is not diagnosed: Continue.
6.Are the brakes binding?
YES - Investigate cause of binding.
NO - Continue.
7.Automatic Transmission only. Is the Torque
Converter and Transmission operating correctly?
Carry out Road test, Static tests and Stall tests
to determine condition of Automatic
transmission.
If problem is not diagnosed: repeat tests starting at 1.Engine backfires into exhaust system
1.Are there any leaking joints/connections or holes
in the exhaust system?
YES -
See MANIFOLD AND EXHAUST
SYSTEM, Repair, Exhaust System
Complete
NO - Continue.
2.Is distributor fitted correctly, HT leads in correct
firing order and routed correctly?
NO -
See ELECTRICAL, Repair, Distributor
- V8i
YES - Continue.
3.Is air fuel ratio correct?
NO - Check multiport fuel injection.
See
Electrical Trouble Shooting Manual.
Check brake vacuum connections.See
BRAKES, Description and operation, Brake
Servo Unit
Check heater/ventilation unit vacuum
connections.
See HEATING AND
VENTILATION, Description and operation,
Heating and Ventilation Unit
Check the crank case and fuel tank ventilation
system.
See EMISSION CONTROL,
Description and operation, Emission Control
YES - Continue.
4.Are cylinder compressions satisfactory?
NO - Carry out compression test to check for
leaking gaskets valves etc.
See
Cylinder Compression - Test
See Repair, Cylinder Heads - Renew
If problem is not diagnosed: repeat tests starting
at 1.

V8i
5
FAULT DIAGNOSIS Engine backfires into inlet system
1.Is the Distributor, HT connections and routing
correct?
NO -
See ELECTRICAL, Repair, Distributor
- V8i
YES - Continue.
2.Is air fuel ratio correct?
NO - Check multiport fuel injection.
See
Electrical Trouble Shooting Manual.
Check brake vacuum connections.See
BRAKES, Description and operation, Brake
Servo Unit
Check heater/ventilation unit vacuum
connections.
See HEATING AND
VENTILATION, Description and operation,
Heating and Ventilation Unit
Check the crank case and fuel tank ventilation
system.
See EMISSION CONTROL,
Description and operation, Emission Control
YES - Continue.
3.Are cylinder compressions satisfactory?
NO - Carry out compression test to check for
leaking gaskets valves etc.
See
Cylinder Compression - Test
For repairSee Repair, Cylinder Heads -
Renew
If problem is not diagnosed: repeat tests starting
at 1.

REAR AXLE AND FINAL DRIVE
1
DESCRIPTION AND OPERATION DESCRIPTION
The welded steel rear axle casing houses a separate
spiral bevel type differential unit, which is off set to the
right of the vehicle centre line. The differential unit
drives the rear wheels via the axle shafts and fully
floating hubs which are mounted on tapered roller
bearings.
Lubrication
The differential is lubricated with oil and the hub
bearings with grease. The hub bearings are fittedwith inner and outer seals. The outer seals prevent
the differential oil mixing with the hub grease and the
inner seals prevent dirt ingress into the hub.
Ventilation
Ventilation of the hub bearings is through the outer oil
seals and the differential ventilation pipe, which
terminates at a high level.
The wheel hubs on axles with ABS brakes share the
same construction to non ABS axles except for the
addition of a sensor ring 11 on the brake disc 10.
Rear axle hub
1. Axle casing
2. Ventilation pipe
3. Axle shaft
4. Wheel studs and hub
5. Wheel bearing stub axle
6. Wheel bearings (2)7. Inner hub seal
8. Outer hub/axle shaft seal
9. Hub lock plate, thrust washer and nuts (2)
10. Brake disc
11. Sensor ring, ABS

REAR AXLE AND FINAL DRIVE
1
REPAIR REAR AXLE
Service repair no - 51.25.01
Remove
WARNING: Remove and refit of axle
requires a further two persons to steady
the axle when lowering or repositioning
axle.
1.Drain brake system.
2.Support chassis rear.
3.Remove road wheels.
4.Support axle weight with hydraulic jack.
5.Disconnect ABS wiring harness multi-plug at
jump hose bracket, if applicable.
6.Disconnect shock absorbers.
7.Disconnect flexible brake hose at connection
under floor.
8.Disconnect lower links at axle.
9.Mark differential and propeller shaft flanges with
identification marks for assembly. Remove four
nuts and bolts. Lower propeller shaft and tie to
one side.10.Disconnect pivot bracket ball joint at axle
bracket.
11.Release bolts and remove coil spring retaining
plates.
12.Lower axle and remove road springs.
13.Disconnect anti-roll[sway] bar links to axle.
See
REAR SUSPENSION, Repair, Anti-Roll[Sway]
Bar Ball Joint Links
14.Remove axle assembly.
Refit
15.Position axle and fit lower links. Tighten to
176
Nm
16.Reverse removal procedure.
17.Tighten pivot bracket ball joint to axle to
176 Nm.
18.Tighten propeller shaft to differential drive flange
to
47 Nm
19.Bleed brake system.See BRAKES, Repair,
Brake System Bleed

51REAR AXLE AND FINAL DRIVE
4
REPAIR Refit
10.Clean stub axle. Retract ABS sensor slightly
from sensor sleeve, if applicable
11.Fit hub assembly to stub axle.
12.Fit spacing washer.
13.Fit hub adjusting nut. Tighten to
61 Nm.
Back off adjusting nut 90°. Tighten to4 Nm.
This will give the required hub end float of
0,010mm
14.Fit a new lock washer.
15.Fit locknut. Tighten to61 Nm.
16.Tab over lock washer to secure adjusting nut
and locknut.
17.Using a new joint washer fit axle shaft to hub,
secure with five bolts. Tighten to
65 Nm.
18.Fit brake caliper. Tighten to82 Nm.
Secure brake pipes to axle casing.
19.If applicable, set ABS brakes sensor.
Push sensor in until it touches sensor ring then
rotate hub to set sensor.
20.Fit road wheel, remove axle stands and final
tighten road wheel nuts to
126 Nm.
21.Operate footbrake to locate brake pads before
driving vehicle.

FRONT AXLE AND FINAL DRIVE
1
DESCRIPTION AND OPERATION DESCRIPTION
The welded steel front axle casing houses a separate
spiral bevel type differential unit, which is off set to the
right of the vehicle centre line. The differential unit
drives the front wheels via the axle shafts and
constant velocity joints which are totally enclosed in
the spherical and swivel housings.
The front axles fitted with ABS brakes or non ABS
brakes are of the same construction except for
different top swivel pins in the swivel housing and a
sensor on the constant velocity joint.
Front axle - ABS
The front wheels are pivoted on taper roller bearings
19 at the bottom of the swivel housing and a 'Rialco
bush' 25 at the top. The top swivel pin also houses the
ABS pickup (electrical connection) as shown in the
main illustration, J5367.
Front axle - non ABS
The front wheels are pivoted on tape roller bearings at
the top (see insert) and bottom of the swivel housing.
The wheel hubs on all axles are supported by two
taper bearings and driven by drive flanges which are
splined to the one piece, stub shaft/constant velocity
joint.
Lubrication
The differential, swivel pin housing and wheel hubs
are indiviudally lubricated and separated by oil seals 7
and 8 to prevent oil transfer across the axle when the
vehicle is traversing steep inclines. The wheel
bearings are lubricated with grease and the swivel
housing and differential with oil.
Ventilation
Ventilation of the differential is through a plastic pipe 2
which terminates at a high level in the vehicle on both
ABS and non ABS axles. The swivel housings
ventilate through axle shaft oil seals 8 into the
differential and the hub bearings vent via the oil seals
into swivel housing.

54FRONT AXLE AND FINAL DRIVE
4
REPAIR Refit
11.Clean stub axle and drive shaft and fit hub
assembly to axle.
12.Fit spacing washer.
13.Fit hub adjusting nut. Tighten to
61 Nm.
14.Back off adjusting nut 90°. Tighten to4 Nm.
This will give the required hub end float of
0,010mm
15.Fit a new lock washer.
16.Fit locknut. Tighten to61 Nm.
17.Tab over lock washer to secure adjusting nut
and locknut.
18.Fit a new joint washer to driving member and fit
member to hub and secure with five bolts.
Tighten to
65 Nm.
19.Fit original drive shaft shim and secure with a
circlip.
20.To check drive shaft end play mount a dial
gauge using bracket LRT-99-503 and rest pin in
a loaded condition on end of drive shaft.
21.Fit a suitable bolt to threaded end of drive shaft.
Move drive shaft in and out noting dial gauge
reading. End play should be between0,08 to
0,25 mm.
22.If end play requires adjustment, remove circlip,
measure shim thickness and fit an appropriate
shim to give required end-play.
23.Remove bolt from drive shaft, fit circlip and dust
cap.
24.Fit brake caliper. Tighten to
82 Nm.
25.Bleed brake system.See BRAKES, Repair,
Brake System Bleed
26.Fit road wheel, remove axle stands and tighten
road wheel nuts to
126 Nm.
27.Operate footbrake to locate brake pads before
taking vehicle on road.

FRONT AXLE AND FINAL DRIVE
11
OVERHAUL Fit driveshaft and stub axle
59.Insert axle shaft, and when differential splines
are engaged, push assembly in fully.
CAUTION: Take care not to damage axle
shaft oil seals.
60.Place a new joint washer in position on swivelpin
housing to stub axle mating face. Coat threads
of stub axle bolts with Loctite 270.
61.Fit stub axle with flat at 12 o'clock position.
CAUTION: Ensure that constant velocity
joint bearing journal is butted against
thrust ring on stub axle. Before stub axle
is secured.
62.Place mud shield in position and secure stub
axle to swivel pin housing with six bolts and
tighten evenly to
65 Nm.
63.Fit brake jump hoses to brake jump hose
bracket.
64.Fit front hub complete assembly.
See Repair,
Front Hub Assembly
65.Check swivel pin housing oil drain plug is fitted.
66.Fill swivel assembly to correct level, with new oil.
See SECTION 10, Maintenance, Under
Vehicle Maintenance
67.Set steering lock stop bolts to provide a
clearance of 20mm.
See STEERING,
Adjustment, Steering Lock Stops
68.Fit ABS brake sensor.See BRAKES, Repair,
Sensors - Front