manual transmission LAND ROVER DISCOVERY 1995 User Guide
[x] Cancel search | Manufacturer: LAND ROVER, Model Year: 1995, Model line: DISCOVERY, Model: LAND ROVER DISCOVERY 1995Pages: 873, PDF Size: 12.89 MB
Page 403 of 873
R380
1
REPAIR R380 MANUAL GEARBOX
Service repair no - 37.20.02
Remove
WARNING: Where the use of a
transmission hoist is necessary, it is
absolutely essential to follow the
manufacturer's instructions to ensure safe and
effective use of equipment.
1.Install vehicle on a ramp [hoist].
2.Disconnect battery earth lead.
3.Remove centre console.
See CHASSIS AND
BODY, Repair, Centre Console
4.Remove sound insulation from top of
transmission tunnel.
5.Remove bolt and remove upper gear lever.
6.Remove screws securing gear selector lever and
high/low selector lever draft excluders.
7.Remove draft excluder clamp rings.
8.Remove handbrake cable clevis pin clip and
clevis pin.
9.Remove 'C' clip and cable adjuster.
10.Select low range to prevent gear lever fouling
tunnel when removing gearbox.
11.Remove bolt securing gearbox breather pipe clip
to cylinder block.
12.Remove bolts securing fan cowl to radiator.
13.Release fan cowl from radiator and lay over fan
blades.
14.Raise ramp [hoist].
15.Drain oil from main gearbox and transfer
gearbox.
See SECTION 10, Maintenance,
Under Vehicle Maintenance
16.Remove exhaust front pipe(s).See MANIFOLD
AND EXHAUST SYSTEM, Repair, Exhaust
System Complete
17.Release intermediate exhaust pipe(s) from
mountings and tie aside.
18.Remove bolts securing clutch slave cylinder.
19.Release slave cylinder from clutch housing and
collect spacer.
20.Mark propeller shaft drive flange relationships for
reassembly.
21.Disconnect front and rear propeller shafts from
transfer gearbox. Tie shafts aside.
22.Remove clamp and disconnect speedometer
cable from transfer gearbox.
23.Release handbrake cable from transmission
tunnel.
24.Temporarily support transmission in a way which
enables the crossmember to be removed and a
hoist cradle to be fitted.
Page 404 of 873
37MANUAL GEARBOX
2
REPAIR 25.Remove nuts and bolts securing transmission
cross-member to chassis.
26.Remove nuts and bolts securing cross-member
mountings to transmission.
27.Remove cross-member.
28.Manufacture an adapter plate to dimensions
given in service tool section and attach it to a
transmission hoist. To achieve balance of the
transmission unit when mounted to hoist, it is
essential that pointA,is situated over lifting hoist
ram. Drill holesBto suit hoist table. Secure the
transmission unit cradle at pointCusing the
lower bolts retaining transfer gearbox rear cover.
Raise hoist just enough to take weight of
transmission.
29.Lower hoist sufficiently to allow transfer gearbox
selector lever to clear transmission tunnel
aperture.
30.Disconnect differential lock switch connectors.
31.Disconnect reverse lamp switch connectors.
32.Remove clips securing gearbox breather pipes
to harness.
33.Support engine under sump with a jack.
CAUTION: Use a wooden block to protect
sump.
34.Remove bell housing nuts.
35.Withdraw transmission whilst ensuring all
connections to engine and chassis are released.36.Remove transmission assembly from hoist
cradle and position safely on a bench.
37.Remove breather pipes. Discard pipe union
sealing washers.
38.Remove 'Nyloc' nut, and remove bolt, securing
lever to high/low shaft.
39.Collect spacer washer.
40.Remove 2 clips and remove differential lock
lever link.
41.Remove lower locknut from high/low operating
rod.
42.Place a sling round transfer box and attach to
hoist.
43.Remove nut and 5 bolts securing transfer
gearbox to extension housing.
44.Withdraw transfer gearbox.