reset LAND ROVER DISCOVERY 1995 User Guide

ELECTRICAL
13
REPAIR EXTERIOR DRIVING MIRRORS
Service repair no - 76.11.10
Replacing the mirror glass
1.Press the outer end of the glass inwards to its
full extent.
2.Insert the fingers under the inner end of the
glass and pull outwards until the glass is
released from its two retaining clips.
3.Disconnect the two demister leads attached to
the back of the glass unit.
4.To replace the glass, locate the inner end of the
glass in the retaining clip of the housing first.
5.Carefully press the outer end of the glass
inwards until it securely locates in the front
retaining clip.
6.Reset the fine adjustment as required.Complete assembly
Service repair no - 76.11.10
Remove
1.Disconnect battery negative lead.
2.Carefully prise off interior finisher to reveal
retaining plate and securing screws.
3.Disconnect electrical plug.
4.Supporting the mirror assembly remove three
securing screws and retaining plate.
5.Detach mirror assembly from outer door frame.
Refit
6.Reverse removal procedure.
NOTE: To prevent damage to the electrical
lead ensure that it is not pushed down
inside the door casing.

ELECTRICAL
33
REPAIR INSTRUMENT BINNACLE COMPONENTS
1. Instrument cowl
2. Face plate
3. Fuel gauge
4. Speedometer
5. Instrument binnacle
6. Screw - securing circuit board
7. Circuit board8. Tachometer
9. Temperature gauge
10. Illumination board
11. Screw securing illumination board
12. Circuit board - instrument illumination
13. Instrument illumination bulb holder and bulb
14. Speedometer trip reset button sleeve
15. Screw - cowl and binnacle

86ELECTRICAL
36
REPAIR SPEEDOMETER
Service repair no - 88.30.01
Remove
1.Remove instrument cowl.
See Instrument
cowl and illumination board
2.Remove speedometer trip reset button sleeve.
3.Remove instrument face plate.
4.Remove 4 screws securing speedometer,
remove speedometer.
Refit
5.Reverse removal procedure.TACHOMETER
Service repair no - 88.30.21
Remove
1.Remove circuit board.
See Circuit board
2.Remove instrument cowl.See Instrument
cowl and illumination board
3.Remove speedometer trip reset button sleeve.
4.Remove instrument face plate.
5.Remove 3 screws securing tachometer to
binnacle, remove tachometer.
Refit
6.Reverse removal procedure.

ELECTRICAL
37
REPAIR COOLANT TEMPERATURE AND FUEL GAUGES
Service repair no - 88.25.14 - Coolant temperature
gauge
Service repair no - 88.25.26 - Fuel gauge
Remove
1.Remove instrument cowl.
See Instrument
cowl and illumination board
2.Remove speedometer trip reset button sleeve.
3.Remove instrument face plate.
Coolant temperature gauge
4.Remove circuit board,See Circuit board
5.Remove 3 screws securing coolant temperature
gauge to binnacle, remove gauge.
Fuel gauge
6.Remove 3 screws securing fuel gauge to
binnacle, remove gauge.
Refit
7.Reverse removal procedure.SPEEDOMETER TRANSDUCER
Service repair no - 88.30.14
Remove
1.Position vehicle on ramp and chock wheels.
2.Raise ramp.
3.Disconnect multiplug from transducer.
4.Remove bolt securing transducer, remove
transducer.
Refit
5.Reverse removal procedure.

ELECTRICAL
41
REPAIR COOLANT TEMPERATURE TRANSMITTER - V8i
Service repair no - 26.10.02
Remove
1.Disconnect battery negative lead.
2.Disconnect lead from transmitter.
3.Remove transmitter, discard sealing washer if
fitted.
Refit
4.Coat threads of replacement transmitter with
Loctite 572.
5.Fit a new sealing washer to transmitter.
6.Fit transmitter, connect lead.
7.Top-up cooling system.HEATED FRONT SCREEN
Heated front screen will operate when switch is
operated, with engine running. Timer unit will provide
a preset time cycle of 7« minutes±20%.
To identify timer unit.
See Electrical Trouble
Shooting Manual.Electrical Troubleshooting
Manual
Switching OFF ignition, or further operation of heated
front screen switch during cycle will switch off screen
and cancel, reset and switch off timer unit.