steering LAND ROVER DISCOVERY 1995 User Guide

09LUBRICANTS, FLUIDS AND CAPACITIES
2
INFORMATION RECOMMENDED LUBRICANTS AND FLUIDS
All climates and conditions
AMBIENT TEMPERATURE°C
COMPONENT SPECIFICATION VISCOSITY -30 -20 -10 0 10 20 30 40 50
Petrol modelsOils must meet: 5W/30
Engine sump
RES.22.OL.G-4 5W/40
or 5W/50
CCMC G-4 or 10W/30
API SG or SH 10W/40
10W/50
15W/40
15W/50
20W/40
20W/50
25W/40
25W/50
DieselRES.22.OL.PD-2 15W/40
Engine sump or CCMC PD-2
or API CD
Main Gearbox
AutomaticATF Dexron IID
Main Gearbox
manualATF Dexron IID
Final drive units API or GL5 90 EP
Swivel pin housings MIL - L - 2105 or
MIL - L - 2105B 80 EP
CorD
Power steering ATF Dexron IID
Transfer box API GL4 or GL5 90 EP
LT230T MIL - L - 2105 or
MIL - L - 2105B 80 EP
CorD

09LUBRICANTS, FLUIDS AND CAPACITIES
4
INFORMATION CAPACITIES
The following capacity figures are approximate and are provided as a guide only.
Capacities (approx.)* Litres Imp.Unit US unit
Engine sump oil
- 300Tdi models 5,8...................................................... 10.20 pt 12.30 pt
- V8i petrol models 3.9 6,1............................................ 10.70 pt 12.90 pt
- Mpi petrol models 4,90.................................................. 8.70 pt 10.40 pt
Extra when refilling after fitting new filter
- 300Tdi models 0,85...................................................... 1.50 pt 1.80 pt
- V8i petrol models 0,56.................................................. 1.00 pt 1.20 pt
- Mpi 0,4........................................................................ 0.70 pt 0.85 pt
Manual gearbox 2,67............................................................... 4.70 pt 5.70 pt
Automatic gearbox 9,1........................................................... 16.00 pt 19.20 pt
Transfer gearbox oil 2,30......................................................... 4.00 pt 4.90 pt
Front differential 1,70............................................................... 3.00 pt 3.60 pt
Rear differential 1,70................................................................ 3.00 pt 3.60 pt
Power steering box and reservoir LHD 2,90............................ 5.00 pt 6.00 pt
Power steering box and reservoir RHD 3,40............................ 6.00 pt 7.20 pt
Swivel pin housing oil (each) 0,35............................................ 0.60 pt 0.75 pt
Fuel tank usable fuel 89,0........................................................ 19.5 gall 23 gall
Cooling system
- 300Tdi models 11,50...................................................... 20.20 pt 24.30 pt
- V8i petrol models 11,30.................................................. 20.00 pt 23.90 pt
- Mpi 10,00........................................................................ 17.60 pt 21.00 pt
Washer bottle 7,0................................................................... 12.30 pt 14.80 pt
NOTE: * All levels must be checked by dipstick or level plugs as applicable. When draining oil
from the ZF automatic gearbox, oil will remain in the torque converter, refill to high level on
dipstick only.

MAINTENANCE
3
MAINTENANCE VEHICLE EXTERIOR
CHECK/ADJUST HEADLAMP ALIGNMENT
Check/adjust headlamp and auxiliary alignment.
CHECK FRONT WHEEL ALIGNMENT
Use recognised wheel alignment equipment to
perform this check and adjustment.
See STEERING,
Adjustment, Front Wheel Alignment
REMOVE WHEELS, CHECK TYRES
Check tyres (including spare) for compliance with
manufacturers' specification.
Check visually for cuts, lumps, bulges, uneven tread
wear and tread depth. Check road wheels for
damage.
Check/adjust tyre pressures.
CHECK/TIGHTEN TOWING BRACKET FITTINGSINSPECT BRAKE PADS FOR WEAR, CALIPERS
FOR LEAKS AND CONDITION
Check thickness of brake pads, fit new pads if
minimum thickness is less than 3,0mm. Check brake
pads for oil contamination. If new brake pads required.
See BRAKES, Repair, Front Brake Pads
or.See BRAKES, Repair, Rear Brake Pads
WARNING: When renewing brake pads, it
is essential that only genuine components
with correct grade of lining are used.
Always fit new pads as complete axle sets, NEVER
individually or as a single wheel set. Serious
consequences could result from out of balance
braking due to mixing of linings.
Refit road wheels
Fit road wheels in original hub position. Secure in
position with wheel nuts, do not fully tighten wheel
nuts at this stage, lower vehicle and finally tighten
wheel nuts to correct torque.
Alloy wheels:
130 Nm.
Steel wheels:130 Nm.
LUBRICATE ALL HINGES, DOOR CHECK
MECHANISMS, BONNET [HOOD] CATCHES AND
FUEL FILLER FLAP

10MAINTENANCE
10
MAINTENANCE
CHECK/TOP UP COOLING SYSTEM
1.To prevent corrosion of aluminium alloy engine
parts it is imperative that cooling system is filled
with a solution of water and phosphate free
anti-freeze, winter or summer. Never fill or top up
with plain water.
WARNING: Do not remove filler cap when
engine is hot because cooling system is
pressurised and personal scalding could
result.
2.When removing filler cap, turn cap slowly
anti-clockwise, pause and allow all pressure to
escape.
3.Continue to turn until cap is removed.
4.When engine is cold expansion tank coolant
should be level with top of indicator post, visible
inside tank through filler hole.
5.If necessary, top up cooling system with
premixed coolant. Use soft water whenever
possible, if local water supply is hard, rainwater
should be used.
6.When replacing filler cap it is important that it is
tightened down fully. Failure to tighten filler cap
properly may result in water loss, with possible
damage to engine
The cooling system should be drained and flushed at
2 year intervals or at onset of second winter. Refer to
Coolant Requirements.
See COOLING SYSTEM,
Adjustment, Coolant RequirementsCHECK/ TOP UP POWER STEERING FLUID
RESERVOIR
1.Remove fluid reservoir cap. Check that fluid is
up to high mark on dipstick.
CHECK/ TOP UP CLUTCH AND BRAKE FLUID
RESERVOIRS
CAUTION: Brake fluid can damage
paintwork. If spillage occurs, wash
affected area IMMEDIATELY with a large
quantity of water.
CHECK/TOP UP WASHER RESERVOIR
Top up washer reservoir to within 25 mm of filler neck.
Use a screen washer solvent/anti-freeze solution to
assist removing mud, flies and road film and protect
against freezing.
LUBRICATE ACCELERATOR AND CRUISE
CONTROL LINKAGES
CHECK/ADJUST IGNITION TIMING - V8i
CATALYST
Check ignition timing.See ENGINE TUNING
DATA, Information, Engine 3.9 V8i

MAINTENANCE
11
MAINTENANCE
CHECK/ADJUST ENGINE IDLE SPEED - Tdi
For idle speed.See ENGINE TUNING DATA,
Information, 300 Tdi Engine
CHECK ENGINE IDLE SPEED - Mpi
For idle speed.See ENGINE TUNING DATA,
Information, Engine - Mpi - 2.0 Litre
CHECK/ADJUST STEERING BOX V8i - Tdi - Mpi
Check steering box for fluid leaks.
Check that there is no backlash in steering box in
straight ahead position. Adjust steering box if
necessary.
See STEERING, Adjustment, Power
Steering Box
CLEAN BATTERY CONNECTIONS
NOTE: Some 96 models are fitted with
battery backed-up sounder
See
ELECTRICAL, Repair, Battery
Remove battery terminals, clean and coat with
petroleum jelly.
A low maintenance battery is installed in vehicle.
Dependent upon climate conditions electrolyte levels
should be checked as follows:
Temperate climates every three years.
Hot climates every year.
RENEW CAMSHAFT DRIVE BELT - Tdi
Renew camshaft drive belt.See ENGINE, Repair,
Camshaft Drive Belt and Gears
The engine timing gears are driven by a flexible
rubber belt which must be renewed at intervals
determined by the severity of operating conditions.
In reasonable, temperate climate operation, renew the
belt every 120,000 km (72,000 miles) or every 6 years
whichever occurs earlier.
In adverse operating conditions such as work in dusty
atmospheres, high ambient temperatures and desert
and tropical zones, renew the belt every 60,000 km
(36,000 miles) or every 3 years whichever occurs
earlier.
CAUTION: If the drive belt is not renewed
at the correct interval, it could fail,
resulting in serious damage.
RENEW CAMSHAFT DRIVE BELT - Mpi
Renew every 160,000 km (96,000 miles) or every 6
years. In adverse conditions every 80,000 km (48,000
miles).
For details of renewing camshaft drive belt.
See
ENGINE, Repair, Camshaft Drive Belt - Mpi
CHECK CAMSHAFT DRIVE BELT - Mpi
For details of checking camshaft drive belt.See
ENGINE, Repair, Check Camshaft Drive Belt - Mpi

10MAINTENANCE
16
MAINTENANCE
LUBRICATE PROPELLER SHAFT SLIDING , AND
UNIVERSAL JOINTS
1.Clean all grease nipples on front and rear
propeller shafts.
2.Using a low pressure hand grease gun, apply
recommended grease, to grease nipples at front
and rear propeller shaft universal and sliding
joints.
NOTE: The rear propeller shaft flexible
coupling is not fitted with a grease nipple.
CHECK VISUALLY BRAKE, FUEL, CLUTCH
PIPES/UNIONS FOR CHAFING LEAKS AND
CORROSION
CHECK EXHAUST SYSTEM FOR LEAKS,
SECURITY AND DAMAGE
CHECK FOR FLUID LEAKS FROM POWER
STEERING AND SUSPENSION SYSTEMS,
HYDRAULIC PIPES AND UNIONS FOR CHAFING
AND CORROSION
CHECK/TIGHTEN STEERING UNIT AND STEERING
ROD BALL JOINT FIXINGS, CHECK CONDITION
OF OF BALL JOINTS AND DUST COVERS
Ball joints are lubricated for their normal life during
manufacture and require no further lubrication. This
applies ONLY if rubber boot has not been dislodged
or damaged. Joints should be checked at specified
mileage intervals but more frequently if vehicle is used
under arduous conditions.
1.Check for wear in joints by moving ball joint up
and down vigorously. If free movement is
apparent fit a new joint assembly.

10MAINTENANCE
18
MAINTENANCE
ABS VEHICLES - CHECK ROAD WHEEL SPEED
SENSOR ELECTRICAL HARNESS FOR DAMAGE
RENEW OXYGEN SENSORS
See EMISSION CONTROL, Repair, Heated
Oxygen Sensor (HO2S)
RENEW CATALYTIC CONVERTERS
See MANIFOLD AND EXHAUST SYSTEM, Repair,
Exhaust System Complete
REPORT ANY UNUSUAL FEATURES OF VEHICLE
CONDITION AND ADDITIONAL WORK REQUIREDCARRY OUT ROAD TEST
For details of dynamometer testing.See
INTRODUCTION, Information, Dynamometer
Testing - Non Anti-lock brake vehicles See
INTRODUCTION, Information, Dynamometer
Testing - Vehicles with Anti-lock brakes (ABS)
Check following items:
1.Inhibitor switch only operates in P and N.
2.Engine for excessive noise.
3.Clutch for slip, judder or spin.
4.Automatic gear selection/shift speeds.
5.Gear selection/noise - high/low range.
6.Steering for abnormal noise/effort.
7.Steering for free play.
8.All instruments, gauges and warning indicators.
9.Heater and air conditioning systems.
10.Heated rear screen.
11.Shock absorbers - ride irregularities.
12.Foot brake, on emergency stop, pulling to one
side, binding, pedal effort.
13.Parkbrake efficiency.
14.Seat reclining and latching.
15.Fully extend seat belt, check operation of
retraction and latching. Inertia belts lock when
snatched or vehicle on slope.
16.Road wheel balance.
17.Transmission for vibrations.
18.Body noises, squeaks and rattles.
19.Excessive exhaust smoke.
20.Engine idle speed.
21.Endorse service record.
22.Report any unusual features of vehicle condition
and additional work required.
ENDORSE SERVICE RECORD

Tdi
3
REPAIR ENGINE
Service repair no - 12.41.01
Remove
CAUTION: Seal all exposed pipe ends
against ingress of dirt after disconnection.
1.Park vehicle on level ground and apply park
brake.
2.Disconnect battery negative lead.
3.Remove bonnet [hood].
See CHASSIS AND
BODY, Repair, Bonnet [Hood]
4.If air conditioning is fitted, remove RH footwell
side trim panel and disconnect harness multiplug
from relay.
5.Disconnect the two engine harness multiplugs
on LH side of footwell.
6.Remove engine harness grommet from
bulkhead and move harness into engine bay.
7.Release battery positive lead from retaining clip
at base of suspension turret.
8.Remove Radiator Assembly.
See COOLING
SYSTEM, Repair, Radiator
9.Discharge air conditioning system.See AIR
CONDITIONING, Adjustment, Refrigerant
Recovery Recycling Recharging
Remove retaining bolts and disconnect both pipe
adaptors from rear of compressor.
10.Remove rocker cover insulation.
11.Disconnect cyclone hose from air cleaner hose.
12.Remove air cleaner hose from turbocharger.
13.Remove feed pipe/hose from turbocharger and
intercooler.
14.Disconnect heater hoses from cylinder head and
heater rails.
15.Remove bolt securing transmission breather
pipe clip to cylinder head; move breather pipes
aside.
16.Disconnect inlet and outlet hoses from power
steering pump.
17.Disconnect bypass hose from thermostat
housing.
18.Release bypass hose from retaining clips on
front timing cover.
19.Remove split pin securing inner throttle cable to
injector pump.
20.Depress tags on outer cable adjusting nut,
remove cable from mounting bracket, and move
aside.
21.If automatic transmission is fitted, release
kickdown cable from injector pump and mounting
bracket.

V8i
5
REPAIR CYLINDER HEADS - RENEW
Service repair no - 12.29.15
1.Remove cylinder heads and gaskets.
See
Cylinder Head Gaskets - Renew
2.Remove spark plugs.
3.Using spring compressor LRT-12-034, remove
seals, valves, collets, springs and caps.
CAUTION: Keep components in fitted
order
4.From left hand cylinder head, remove earth lead
studs.
5.Remove three bolts securing power steering
pump mounting bracket to cylinder head.
6.Remove four bolts securing generator mounting
bracket to cylinder head.
7.Right hand cylinder head, remove rear lifting
bracket.
8.Fit lifting bracket to new right hand cylinder
head.
9.Fit mounting brackets and earth lead studs to
new cylinder head. Tighten bolts to
30 Nm.
10.Regrind valves- refer to engine overhaul
publication
11.Lubricate valve stems, fit valves, springs, and
caps. Fit new inlet and exhaust valve stem seals.
12.Using spring compressor LRT-12-034, compress
springs, fit collets. Tap valve to check correct
collet seating.
13.Fit spark plugs.
14.Fit cylinder heads with new gaskets.
See
Cylinder Head Gaskets - Renew
ROCKER COVER - RIGHT HAND - RENEW
Service repair no - 12.29.41
1.Disconnect battery negative lead.
2.Disconnect purge pipe from charcoal canister at
plenum.
3.Remove breather pipe from rocker cover.
4.Remove coolant pipes from inlet manifold.
5.Remove spark plug leads from plugs and
retaining clips.
6.Remove four rocker cover bolts. Moving fuel
pipes aside, remove rocker cover.
7.Discard rocker cover gasket.
8.Remove plug lead retaining clips from rocker
cover, fit to new rocker cover.
9.Clean and dry rocker cover and cylinder head
mating faces, using Bostik cleaner 6001.
NOTE: Gasket fits one way round only. It
must be fitted accurately, first time.
Subsequent movement will destroy
bonding.
10.Apply Bostik 1775 impact adhesive to rocker
cover seal face and gasket, using a brush to
ensure an even film. Allow adhesive to become
touch dry.

V8i
9
REPAIR FRONT COVER GASKET
Service repair no - 12.65.04
1.Remove crankshaft pulley.
See Crankshaft
Pulley Assembly. Do not remove pulleys
2.Remove water pump pulley.
3.Release distributor cap clips.
4.Release plug leads from plugs and clips.
5.Place cap and leads to one side.
6.Turn engine until No. 1 piston is at T.D.C.
7.Check position of rotor arm.
8.Remove fixings securing power steering pump
bracket to water pump bracket.
9.Remove power steering pump bracket from
water pump.
10.Remove clips securing wiring to generator
tensioner.
11.Disconnect distributor feed wire.
12.Pivot power steering pump away from front
cover, tighten pivot to retain in position.
13.Disconnect vacuum pipe from distributor.
14.Remove water pump bottom hose.
15.Disconnect oil pressure switch.
16.Disconnect heater hose at water pump.
17.Remove generator tensioner from water pump,
move tensioner aside.
18.Mark distributor position to front cover.
19.Remove distributor clamp, remove distributor.
See ELECTRICAL, Repair, Distributor - V8i
20.Remove fixings sump to front cover.
21.Loosen four adjacent sump fixings.
22.Remove generator support strut from front cover,
move strut aside.
23.Loosen remaining front cover fixings and remove
front cover.
24.Remove front cover gasket.Refit
25.Clean timing cover, clean block face.
26.Lightly grease gasket faces.
27.Fit new gasket to block face.
28.Apply hylosil to sump gasket.
29.Clean threads of cover fixing bolts, apply Loctite
372 to threads.
30.Fit timing cover, fit fixing bolts. Tighten to
28
Nm.
31.Fit generator support strut to front cover.
32.Tighten sump to timing cover fixings to
10 Nm.
33.Tighten sump fixings to10 Nm.
34.Lubricate distributor O ring.
35.Fit distributor in position marked.
36.Align oil pump drive, if distributor does not seat
correctly.
37.Fit distributor clamp. Tighten to
20 Nm.
38.Locate generator tensioner on water pump
bracket.
39.Connect heater hose, tighten clip.
40.Connect oil pressure switch.
41.Connect bottom hose, tighten clip.
42.Connect vacuum pipe to distributor.
43.Loosen power steering pump pivot, lower pump.
44.Connect distributor feed wire.
45.Connect wire ties to generator tensioner.
46.Fit power steering pump bracket to water pump.
Tighten to
28 Nm.
47.Fit power steering pump to bracket.
48.Position distributor cap. Fit plug leads to plugs
and clips.
49.Clip distributor cap in position.
50.Fit water pump pulley. Tighten to
10 Nm.
51.Fit crankshaft pulley.See Crankshaft Pulley
Assembly
52.Tension drive belts correctly.
53.Check ignition timing.
54.Refill cooling system.