service LAND ROVER DISCOVERY 1995 Workshop Manual

60FRONT SUSPENSION
6
REPAIR ANTI-ROLL[SWAY] BAR BALL JOINT LINKS
Service repair no - 60.10.04.
Remove
1.Remove two nuts, bolts, washers and rubber
bushes from ball joint links.
2.Remove cotter pin and loosen castellated nut a
few turns.
3.Release ball joint using special tool 18G 1063A
as shown.
4.Remove castellated nut and ball joint link.
Refit
5.Fit ball joint link and castellated nut. Ensure ball
joint link arm points up. Tighten to
40Nmand fit
new cotter pin.
6.Align anti-roll bar to ball joint links.
7.Fit bolts, washers and rubber bushes using new
self locking nuts secure anti-roll[sway] bar to ball
joint links. Tighten to
68Nm.

REAR SUSPENSION
1
REPAIR REAR ROAD SPRING
Service repair no - 64.20.01
Remove
1.Loosen rear road wheel retaining nuts.
2.Support chassis on stands and remove wheels.
3.Support rear axle weight with jack.
4.Disconnect shock absorbers at one end.
5.Position coil spring compressor correctly on road
spring.
6.Compress spring evenly to facilitate removal.
7.Lower axle to free road spring from upper seat.
CAUTION: Avoid lowering axle further than
rear brake flexible hose will allow.
8.Remove spring retainer plate.
9.Withdraw road spring, and spring isolator.
10.Lift off spring seat.
Refit
11.Reverse removal procedure.REAR SHOCK ABSORBER
Service repair no - 64.30.02.
Remove
1.Loosen road wheel retaining nuts.
2.Support chassis on stands. Remove road wheel
and support rear axle weight with jack.
3.Remove fixings and withdraw shock absorber
from axle bracket.
4.Remove upper fixings.
5.Withdraw shock absorber.
6.If required remove mounting bracket
7.If required remove mounting rubbers.
Refit
8.Reverse removal procedure.

64REAR SUSPENSION
2
REPAIR BUMP STOP
Service repair no - 64.30.15.
Remove
1.Remove fixings.
2.Remove bump stop.
Refit
3.Position bolts in slots in bracket.
4.Fit bump stop secure with washer and nuts.SUSPENSION LINK UPPER
Service repair no - 64.35.44.
Remove
1.Support rear of chassis on stands, allow axle to
hang freely.
2.Remove fixings, upper link bracket to frame.
3.Remove fixings, upper links to pivot bracket.
4.Remove upper link complete with frame bracket.
5.Remove bolt.
6.Separate link from bracket.

REAR SUSPENSION
3
REPAIR Renew bush
7.Press out rubber bushes.
8.Fit bush centrally in housing.
CAUTION: Apply pressure to outer edge of
bush, and not rubber inner.
Refit
9.Reverse removal procedure. 1 to 6. Do not fully
tighten fixings until all components are in
position.
10.Tighten fixings to correct torque.
See
Specifications, torque, Torque Values
SUSPENSION LINK LOWER
Service repair no - 64.35.02.
Remove
1.Site vehicle on a ramp [hoist].
2.Alternatively, support vehicle on stands under
rear axle.
3.Remove rear fixings.
4.Remove mounting bracket fixings at side
member bracket.
5.Remove lower link complete.
6.Remove locknut.
7.Remove mounting bracket from lower link.
Renew bush
8.Press out rubber bushes.
9.Fit bush centrally in housing.
CAUTION: Apply pressure to outer edge of
bush, and not rubber inner.
Refit
10.Reverse removal procedure. 6 and 7. Do not
tighten locknut.
11.Reverse removal procedure. 3 to 5.
12.Lower vehicle, allow axle to take up static laden
position. Tighten to
176 Nm.

64REAR SUSPENSION
4
REPAIR ANTI-ROLL[SWAY] BAR ASSEMBLY REAR
Service repair no - 64.35.08.
KEY
1. Anti-roll[sway] bar
2. Rubber bush
3. Strap
4. Nut, bolt, washer5. Nut and washer
6. Ball joint link arm
7. Bolt and washer
8. Castellated nut and cotter pin
Remove
1.Note for reassembly, position of rubber bushes
on anti-roll bar.
2.Remove four nuts, bolts and washers securing
two bush straps.
3.Remove nuts, bolts, washers and rubber bushes
from the ball joint links and remove anti-roll bar.Refit
4.Position rubber bushes on anti-roll bar. Fit joint
towards axle.
5.Fit anti-roll bar with two straps. Ensure ball joint
link arms point down as shown. Loosely fit, bolts,
washers and new nyloc nuts.
6.Fit bolt, washers and rubber bushes. Fit anti-roll
bar to ball joint links. Tighten to
68Nm.
7.Tighten nuts securing straps to30Nm.

REAR SUSPENSION
5
REPAIR ANTI-ROLL[SWAY] BAR BALL JOINT LINKS
Service repair no - 64.35.24.
Remove
1.Remove two nuts, bolts, washers and rubber
bushes from ball joint links and lower anti-roll bar
to clear links.
2.Remove cotter pin and loosen castellated nut a
few turns.
3.Release ball joint using special tool 18G 1063A
as shown.
4.Remove castellated nut and ball joint link.
Refit
5.Fit ball joint link arm and castellated nut. Point
ball joint link arm down as shown. Tighten to
40Nmand fit new cotter pin.
6.Align anti-roll bar to ball joint links.
7.Fit bolts, washers and rubber bushes using new
self locking nuts secure anti-roll bar to ball joint
links. Tighten to
68Nm.

BRAKES
1
DESCRIPTION AND OPERATION BRAKES
Discovery vehicles have servo assisted brake
systems and the option of an anti-lock brake system.
Information in this section refers to components
relevant to both brake systems. Where the system
components are different they are referred to as ABS
or NON ABS
BRAKE SYSTEM NON ABS
Description
The servo assisted hydraulic braking system is the
dual line type, incorporating primary and secondary
hydraulic circuits.
NOTE: References made to primary or
secondary do not imply main service
brakes or emergency brakes but denote
hydraulic line identification.
The brake pedal is connected to a vacuum assisted
mechanical servo which in turn operates a tandem
master cylinder. The front disc brake calipers each
house four pistons, these pistons are fed by the
secondary hydraulic circuit. The rear disc brake
calipers each house two pistons, these are fed by the
primary hydraulic circuit via a pressure reducing valve.
A brake fluid level switch is incorporated into the
reservoir cap assembly, the switch will immediately
illuminate a warning light in the instrument binnacle
indicating low fluid or sudden fluid loss.
The brake fluid reservoir is divided, the section closest
to the servo feeds the primary circuit and the section
furthest from the servo feeds the secondary circuit.
Under normal operating conditions both the primary
and secondary circuits operate simultaneously on
brake pedal application. In the event of a failure in the
primary circuit the secondary circuit will still function. If
the secondary circuit fails the primary circuit will still
function. The brake pedal travel will be longer in the
event of a half system failure.If the servo should fail, both hydraulic circuits will still
function but would require greater pedal effort due to
the lack of vacuum assistance. The hand operated
parking brake acts on a brake drum at the rear of the
transfer gearbox and is completely independent of the
hydraulic circuits.
Hydraulic circuit non ABS
Key
A = Primary hydraulic circuit
B = Secondary hydraulic circuit
C = Pressure reducing valve

BRAKES
3
DESCRIPTION AND OPERATION Description of components
1. ABS Modulator unit
To provide the ABS function a Modulator is positioned
within the system between the master cylinder and the
calipers. On both LHD and RHD vehicles it is sited on
the left inner wing [fender]. The Modulator has 8
solenoid valves, 2 for each wheel, 2 expanders and a
recirculation pump. It is non serviceable.
2. Servo/master cylinder
Actuation of the system is provided by a combined
master cylinder and servo assembly attached to the
pedal box, this provides pressure to opposed piston
calipers at each brake pad Twin piston at the front
axle, single piston at the rear.
3. Pressure reducing valve
To maintain the braking balance, pressure to the rear
axle is regulated by a Pressure Reducing Valve (PRV)
This PRV is of the failure bypass type, allowing full
system pressure to the rear axle in the event of a front
circuit failure. It is sited on the left inner wing [fender].
4. Electronic control unit - ECU
ABS control is provided by an electronic control unit
which is positioned on the passenger side of the
vehicle behind the dash panel/glove box.
The ECU, which is non-serviceable, is connected to
the ABS harness by a 35 way connector. non
serviceable.
The ECU continually monitors the brake system,
providing diagnostics in the event of a system
malfunction. Details of how to access the ECU
diagnostics are provided in the Electrical
Troubleshooting Manual.
5.& 6. Front and rear sensors/exciter rings - 4 off
A sensor is sited at each wheel, sensing a 60 tooth
exciter ring. When vehicle is in motion inductive
sensors send signals to ECU. Front exciter ring is
fitted to outside diameter of constant velocity joint
inside each front hub assembly. The rear exciter ring
is bolted to the rear of each brake disc bell.7. Diagnostic plug connection
A diagnostic plug is located behind the dash. To the
left of the steering column on LHD vehicles. To the
right of the steering column on RHD vehicles. It is a 5
way blue connector.
The location and identification of ABS electrical relays
are given in the Electrical Troubleshooting Manual.
For location and identification of ABS electrical fuses.
See ELECTRICAL, Repair, Fuse Box - Interioror.
See ELECTRICAL, Repair, Fuse Box - Engine
Compartment
ANTI-LOCK BRAKE SYSTEM - ABS
Manufactured by WABCO
Introduction
The purpose of ABS is to prevent vehicle wheels
locking during brake application, thus maintaining
vehicle steerability and stability. This allows vehicle to
be steered whilst brakes are applied, even under
emergency conditions, and to avoid obstacles where
there is sufficient space to redirect the vehicle.
WARNING: ABS is an aid to retaining
steering control and stability while
braking.
·ABS cannot defy the natural laws of physics
acting on the vehicle.
·ABS will not prevent accidents resulting from
excessive cornering speeds, following
another vehicle too closely or aquaplaning,
i.e. where a layer of water prevents adequate
contact between tyre and road surface.
·The additional control provided by ABS must
never be exploited in a dangerous or
reckless manner which could jeopardise the
safety of driver or other road users.
·The fitting of ABS does not imply that the
vehicle will always stop in a shorter stopping
distance.

BRAKES
1
REPAIR GENERAL BRAKE SERVICE PRACTICE
Brake fluid precautions
WARNING: Do not allow brake fluid to
come into contact with eyes or skin.
CAUTION: Brake fluid can damage
paintwork, if spilled wash off immediately
with plenty of clean water.
CAUTION: Use only correct grade of brake
fluid. If an assembly fluid is required use
ONLY brake fluid. Do NOT use mineral oil,
i.e. engine oil etc.
CAUTION: Thoroughly clean all brake
calipers, pipes and fittings before
commencing work on any part of the brake
system. Failure to do so could cause foreign
matter to enter the system and cause damage to
seals and pistons which will seriously impair the
efficiency of the brake system.
·To ensure the brake system efficiency is not
impaired the following warnings must be
adhered to :-
·DO NOT use any petroleum based cleaning
fluids or any proprietary fluids containing
petrol.
·DO NOT use brake fluid previously bled from
the system.
·DO NOT flush the brake system with any fluid
other than the recommended brake fluid.
The brake system should be drained and flushed
at the recommended service intervals.
Cover all electrical terminals carefully to make
absolutely certain that no fluid enters the
terminals and plugs.FLUID LEVEL CHECK / TOP UP
WARNING: Clean reservoir body and filler
cap before removing cap. Use only fluid
from a sealed container.
1.Park vehicle on level ground.
2.Check level is between 'MIN' and 'MAX' marks.
3.If level is below 'MIN' mark top up fluid level to
'MAX' mark on reservoir, using correct fluid.
See
LUBRICANTS, FLUIDS AND CAPACITIES,
Information, Recommended Lubricants and
Fluids
Do not fill reservoir above maximum line

70BRAKES
2
REPAIR BRAKE SYSTEM BLEED
Service repair no - 70.25.02
The following method for bleeding the hydraulic brake
system applies to both ABS and NON ABS vehicles.
Preparation
WARNING: Before bleeding the brake
system refer to general brake service
practice.
See General Brake Service
Practice
·During bleed procedure, brake fluid level
must not be allowed to fall below the MIN
level. Keep reservoir topped to the MAX level.
·To bleed the hydraulic circuits four bleed
nipples are provided, one at each caliper.
·There are two methods by which air can be
removed from the braking system:-
1. MANUAL BLEED PROCEDURE.
2. PRESSURE BLEED PROCEDURE.
Pressure bleed procedure
Purpose designed equipment for pressure filling and
bleeding of hydraulic systems may be used on Land
Rover vehicles. The equipment manufacturer's
instructions must be followed and the pressure must
not exceed 4.5 bar.
Manual bleed procedure
Equipment required
·Clean glass receptacle
·Bleed hose
·Wrench
·Approx 2 litres brake fluid.
See
LUBRICANTS, FLUIDS AND CAPACITIES,
Information, Recommended Lubricants and
Fluids
Master cylinder bleed
1.Disconnect battery negative lead.
2.Depress brake pedal fully and slowly 5 times.
3.Release the pedal and wait for ten seconds.
4.Air bubbles will rise into the reservoir during
these instructions.
5.Repeat instructions until a firm resistance is felt
at the pedal.
Complete circuit bleed
1.Disconnect battery negative lead.
2.Fit bleed hose to any caliper bleed screw.
3.Dip free end of bleed hose into brake fluid in
bleed bottle.
4.Open bleed screw of caliper.
5.Depress brake pedal fully several times until fluid
is clear of air bubbles.
6.Keeping pedal fully depressed, tighten bleed
screw, then release pedal.
7.Repeat the above procedure on remaining three
calipers.
8.Fit all bleed screw protection caps.
9.Check/top-up fluid level when bleeding is
complete.
See Fluid Level Check / Top-Up