seats LAND ROVER DISCOVERY 1995 Owner's Manual
[x] Cancel search | Manufacturer: LAND ROVER, Model Year: 1995, Model line: DISCOVERY, Model: LAND ROVER DISCOVERY 1995Pages: 873, PDF Size: 12.89 MB
Page 736 of 873

CHASSIS AND BODY
69
REPAIR FRONT SEAT BELTS - 5 DOOR (96 MODELS)
Service repair no - 76.73.10
Remove
1.Move the seat to gain access to the seat belt
mountings.
2.Remove the cover and securing bolt to release
the upper mounting and spacer from the 'B' post
adjustable mounting.
3. Electric seats only:Release fixings securing
the seat side valance.
4.Remove the side valance.
5.Remove the Torx bolt securing the lower
mounting to the seat.
6.Detach the door seals from the 'B' post
sufficiently to allow removal of the lower trim
panel from the post.
7.Release the seat belt from the split section at the
top of the trim panel and withdraw the panel.
Page 748 of 873

80HEATING AND VENTILATION
6
REPAIR BLOWER MOTOR UNIT - HEATER AND AIR
CONDITIONING
Service repair no - 80.20.17
Service repair no - 82.25.54.
Remove
1.Move seats to rear most position.
2.Disconnect battery negative lead.
3.Remove fascia panel assembly.
See CHASSIS
AND BODY, Repair, Dash Panel Assembly
4.Remove 2 nuts securing lower brackets to
toeboard.
5.Manoeuvre blower unit from heater unit and
remove.
Refit
6.Reverse removal procedure. Ensure seal
between blower and heater unit is tight.BLOWER MOTOR
Service repair no - 80.20.17
Service repair no - 82.25.33.
Remove
1.Remove blower motor unit.
See Blower Motor
Unit - Heater and Air Conditioning
2.Release wiring harness retaining clip.
3.Remove 3 screws securing casing.
4.Remove blower motor assembly.
Page 831 of 873

ELECTRICAL
11
REPAIR HANDSET INITIALISATION
NOTE: New handsets are supplied in pairs.
If a new handset is required, it will require
initialisation to the ECU using the
following procedure:
1.Starting conditions: ignition off, doors unlocked,
bonnet switch depressed.
2.Carry out instructions 3. to 9. within 8 seconds.
3.Switch ignition ON.
4.Switch ignition OFF.
5.Lock doors.
6.Unlock doors.
7.Release bonnet switch.
8.Switch ignition ON.
9.Switch ignition OFF.
If alarm is correctly accessed, horn will sound and
LED will light. It is now possible to programme two
handsets of correct frequency to vehicle alarm ECU.
This must be carried out within two minutes.
10.Press and hold down button on first handset until
dash LED flashes.
11.Repeat instruction 10. for second handset.
12.The LED will extinguish if both handsets have
been initialised correctly.CENTRAL DOOR LOCKING
Where electrically operated central door locking is
fitted, locking or unlocking the drivers door from
outside by key operation, or from the inside with the
sill knob automatically locks or unlocks the passenger
and rear doors.
Front and rear passenger doors can be independently
locked or unlocked from inside the vehicle by sill knob
operation but can be overidden by further operation of
the driver's door locking control.
On rear doors, where side facing fold down seats are
fitted, a child safety lock is provided which can be
mechanically pre-set to render the interior door
handles inoperative.
Failure of a door actuator will not affect the operation
of the remaining doors and the door with the
inoperative actuator can still be locked or unlocked
manually.
The actuator unit fitted to the driver's door is the
master actuator and is identified from the actuators
fitted to the passenger and rear doors by having a
white connecting link, whereas the passenger and
rear door actuators have grey coloured connecting
links.
NOTE: Actuator units are non-servicable, if
a fault should occur replace the unit with a
new one.
Page 846 of 873

86ELECTRICAL
26
REPAIR TRAILER SOCKET
Remove
1.If fitted remove the RH side facing seat
See
CHASSIS AND BODY, Repair, Rear Fold
Down Seats
2.Remove the rear lower side trim panelSee
CHASSIS AND BODY, Repair, Rear
Compartment Lower Trim Panels
3.Raise the carpet adjacent to the RH rear quarter
panel.
4.Disconnect the trailer socket lead multi-plug from
the RH body harness.
5.Displace the rubber grommet in the floor and
pass the socket lead through to the underside of
the vehicle.
6.Remove the securing screws and withdraw the
trailer socket from the towing hook mounting
bracket.
Refit
7.Reverse removal procedure.