suspension LAND ROVER DISCOVERY 1995 Owner's Guide

64REAR SUSPENSION
4
REPAIR ANTI-ROLL[SWAY] BAR ASSEMBLY REAR
Service repair no - 64.35.08.
KEY
1. Anti-roll[sway] bar
2. Rubber bush
3. Strap
4. Nut, bolt, washer5. Nut and washer
6. Ball joint link arm
7. Bolt and washer
8. Castellated nut and cotter pin
Remove
1.Note for reassembly, position of rubber bushes
on anti-roll bar.
2.Remove four nuts, bolts and washers securing
two bush straps.
3.Remove nuts, bolts, washers and rubber bushes
from the ball joint links and remove anti-roll bar.Refit
4.Position rubber bushes on anti-roll bar. Fit joint
towards axle.
5.Fit anti-roll bar with two straps. Ensure ball joint
link arms point down as shown. Loosely fit, bolts,
washers and new nyloc nuts.
6.Fit bolt, washers and rubber bushes. Fit anti-roll
bar to ball joint links. Tighten to
68Nm.
7.Tighten nuts securing straps to30Nm.

REAR SUSPENSION
5
REPAIR ANTI-ROLL[SWAY] BAR BALL JOINT LINKS
Service repair no - 64.35.24.
Remove
1.Remove two nuts, bolts, washers and rubber
bushes from ball joint links and lower anti-roll bar
to clear links.
2.Remove cotter pin and loosen castellated nut a
few turns.
3.Release ball joint using special tool 18G 1063A
as shown.
4.Remove castellated nut and ball joint link.
Refit
5.Fit ball joint link arm and castellated nut. Point
ball joint link arm down as shown. Tighten to
40Nmand fit new cotter pin.
6.Align anti-roll bar to ball joint links.
7.Fit bolts, washers and rubber bushes using new
self locking nuts secure anti-roll bar to ball joint
links. Tighten to
68Nm.

REAR SUSPENSION
1
SPECIFICATIONS, TORQUE TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
Anti-roll[sway] bar rear
- Strap nyloc nuts 30..............................................................................
- Ball link self lock nut 68........................................................................
- Castellated nut 40................................................................................
Top link to mounting bracket 176.....................................................................
Bottom link to axle 176.....................................................................................
Bottom link to chassis 176...............................................................................
Top link bracket to rear cross member 47......................................................
Shock absorber to axle 37..............................................................................
Torque values below are for all screws and bolts used except for those that are specified otherwise.
METRIC Nm
M5 6......................................................................................................
M6 9......................................................................................................
M8 25.....................................................................................................
M10 45...................................................................................................
M12 90...................................................................................................
M14 105..................................................................................................
M16 180..................................................................................................
UNC / UNF
1/4 9......................................................................................................
5/16 24...................................................................................................
3/8 39.....................................................................................................
7/16 78...................................................................................................
1/2 90.....................................................................................................
5/8 136....................................................................................................

WHEELS AND TYRES
1
FAULT DIAGNOSIS TYRE WEAR CHART
FAULT CAUSE REMEDY
Rapid wear at Tyres under-inflated Inflate to correct pressure
shoulders Worn suspension components Replace worn components
i.e. ball joints, panhard
rod bushes,steering damper
Excessive cornering speeds
Rapid wear at
centreTyres over-inflated Inflate to correct pressure
of tread
Wear at one
shoulderTrack out of adjustment Adjust track to correct figure
Bent panhard rod Check and replace worn or damaged
components
Bald spots or tyre Wheel out of balance Balance wheel and tyre
cupping assembly
Excessive radial runout Check runout and replace tyre
if necessary
Shock absorber worn Replace shock
Excessive braking
Tyre scalloped Track out of adjustment Adjust toe to correct figure
Worn suspension components Replace as necessary
Excessive cornering speeds
CAUTION: This diagnosis chart is for general guidance only and does not necessarily include
every cause of abnormal tyre wear.

86ELECTRICAL
34
REPAIR PRINTED CIRCUIT AND WARNING LIGHTS
1. Panel illumination bulbs
2. Transmission oil temperature warning lamp bulb
3. Hazard warning lamp bulb
4. Check engine warning lamp bulb
5. Handbrake/brake fluid warning lamp bulb
6. ABS warning lamp bulb
7. Headlamp main beam warning lamp bulb
8. Trailer direction warning lamp bulb9. Direction indicator warning lamp bulb
10. Air suspension warning lamp bulb
11. Ignition/no charge warning lamp bulb
12. Seat belt warning lamp bulb
13. Not used
14. Traction control warning lamp bulb
15. Diesel heater plug warning lamp bulb (if fitted)
16. Main printed circuit