wiring LAND ROVER DISCOVERY 1995 Owner's Guide

ELECTRICAL
17
REPAIR REAR LIGHT UNIT
Service repair no - 86.40.74
Remove
1.Pull out side facing seat or pocket cover.
2.Unscrew fastener and remove access panel.
3.Disconnect wiring harness multi-plug from light
unit.
4.Remove retaining nuts and withdraw light unit
from rear of vehicle.
Key
1. Access panel
2. Multiplug
3. Retaining nut
4. Bulb holder
5. Bulb
Refit
5.Reverse removal procedure. Ensure that the
rubber seal is seated correctly.STOP, REVERSING, FOG GUARD BULBS
Service repair no - 86.40.74
Remove
1.Pull out side facing seat or pocket cover.
2.Unscrew fastener and remove access panel.
3.Turn bulb holder anti-clockwise to release.
4.Remove bulb.
NOTE: On vehicles fitted with rear air
conditioning remove access panel
housing rear loadspace light to gain
access.
Key
1. Access panel
2. Multiplug
3. Retaining nut
4. Bulb holder
5. Bulb
Refit
5.Reverse removal procedure.

ELECTRICAL
19
REPAIR NUMBER PLATE LIGHTS
Service repair no - 86.40.86
Remove
1.Remove two screws and withdraw light unit.
2.Disconnect wiring leads and remove light unit.
3.Remove bulb.
Refit
4.Reverse removal procedure.DOOR EDGE LIGHT
Service repair no - 86.40.35
Remove
1.Pry lens from housing.
2.Disconnect wiring leads and remove light unit.
3.Remove bulb.
Refit
4.Reverse removal procedure.

ELECTRICAL
21
REPAIR INTERIOR LIGHT
Service repair no - 86.35.14
Remove
1.Pry out light unit from roof location.
2.Disconnect light switch plug.
Refit
3.Reverse removal procedure.
Bulb Removal.
1.Pry out interior light lens.
2.Remove bulb.
Refit
3.Reverse removal procedure.REAR LOADSPACE LIGHT
Service repair no - 86.41.40
Remove1.Pry light unit from trim panel.
2.Disconnect wiring leads.
3.Remove bulb.
Refit
4.Reverse removal procedure.

ELECTRICAL
27
REPAIR WINDOW LIFT MOTOR - FRONT
Service repair no - 86.25.04
Remove
1.Ensure that the window glass is in its fully closed
position and secure it with adhesive tape.
2.Disconnect battery negative lead.
3.Remove the door pull, trim panel, and plastic
vapour barrier.
See CHASSIS AND BODY,
Repair, Front Door Trim Panel
4.Release the window lift motor wiring harness
from the three retaining clips to allow the
harness to be pulled out of the opening at the
front of the inner door panel.
5.Disconnect the window lift motor harness
multi-plug from the main door harness.
6.Support the motor, remove the three securing
bolts and withdraw the motor through the top
front opening of the door panel.
Refit
7.Reverse removal procedure.
NOTE: Ensure drive gear is engaged and
correctly aligned with window lift linkage
before fitting securing bolts.WINDOW LIFT MOTOR - REAR
Service repair no - 86.25.09
Remove
1.Ensure that the side door glass is in the fully
closed position and secure with adhesive tape.
2.Disconnect battery negative lead.
3.Remove the door pull, trim panel and plastic
vapour barrier.
See CHASSIS AND BODY,
Repair, Rear Side Door Trim - Panel
4.Disconnect the lift motor harness multi-plug from
the door harness.
5.Support the motor and remove the three
securing screws.
6.Withdraw the motor through the lower opening in
the inner door panel.
Refit
7.Reverse removal procedure.
NOTE: Ensure drive gear is engaged and
correctly aligned with window lift linkage,
before fitting securing bolts.