service LAND ROVER DISCOVERY 1995 Repair Manual

Mpi
1
REPAIR CAMSHAFT FRONT OIL SEAL
Service repair no - 12.13.07 - Exhaust
Service repair no - 12.13.09 - Inlet
Remove
1.Disconnect battery negative lead.
2.Remove drive belt.
See SECTION 10,
Maintenance, Under Bonnet [Hood]
Maintenance
3.Remove 5 bolts, timing belt upper cover.
4.Remove timing belt upper cover.
5.Remove 5 bolts, timing belt centre cover.
6.Remove timing belt centre cover.
7.Rotate crankshaft to align camshaft gear timing
marks - 90°B.T.D.C.
8.Fit tool LRT-12-058 to lock flywheel.
9.Fit tool LRT-12-060 to lock camshaft gears.
10.Loosen camshaft belt tensioner bolt.
11.Move tensioner away from belt and tighten
tensioner bolt.
12.Remove belt from camshaft gears.

12ENGINE
4
REPAIR CRANKSHAFT FRONT OIL SEAL
Service repair no - 12.21.14
Remove
1.Remove timing belt.
See Camshaft Drive Belt
2.Slide timing gear off crankshaft and remove
drive key.
3.Ensure bore of tool is burr free, fit and tighten
tool LRT-12-073 into crankshaft front oil seal.
4.Using thrustpad, tighten centre screw of tool to
remove oil seal.
5.Remove thrust button from crankshaft.
Refit
1.Use lint free cloth and thoroughly clean seal
recess and running surface on crankshaft. Clean
crankshaft gear and pulley.
2.Lubricate oil seal sealing surfaces with engine
oil.
3.Fit tool LRT-12-070 onto crankshaft.
4.Position new oil seal on crankshaft, drift into
place using LRT-12-069 and remove protector.
5.Fit drive key to crankshaft and slide timing gear
onto crankshaft.
6.Fit and tension timing belt.
See Camshaft
Drive Belt

Mpi
5
REPAIR CRANKSHAFT REAR OIL SEAL
Service repair no - 12.21.20
Remove
1.Remove gearbox.
2.Remove clutch assembly.
3.Remove flywheel.
4.Drain engine oil.
5.Fit sump plug, replacing sealing washer if
damaged and tighten to the correct torque.
6.Loosen 15 sump bolts by approximately 3 turns,
allowing sump to drop away from rear oil seal
housing. Do not loosen 3 boltsAaround oil
pump housing.
7.Remove bolts securing oil seal housing, remove
seal and housing assembly.
Refit
1.Clean seal seating area of block and accessible
area of sump gasket. Sump gasket must be
replaced if damaged.
2.Lubricate oil seal sealing surfaces with engine
oil.
3.Fit tool LRT-12-061 over crankshaft boss and fit
oil seal and housing assembly.
4.Remove tool.
5.Fit and tighten seal housing bolts to correct
torque in sequence shown.
10Nm
6.Tighten sump bolts to correct torque and in the
correct sequence.
See Engine Sump Gasket
7.Fit flywheel.
8.Fit clutch assembly.
9.Fit gearbox.

12ENGINE
6
REPAIR ENGINE
Service repair no - 12.41.01
Remove
1.Site vehicle onto ramp [hoist].
2.Remove the drive belt.
See SECTION 10,
Maintenance, Under Bonnet [Hood]
Maintenance
3.Remove radiator.See COOLING SYSTEM,
Repair, Radiator - Mpi
4.Remove bonnet [hood].See CHASSIS AND
BODY, Repair, Bonnet [Hood]
5.Drain engine oil.
6.Position absorbent cloth around fuel pipe to fuel
rail union.
Unscrew union to relieve pressure.
CAUTION: Plug the connections
7.Release clip and disconnect hose from coolant
pump.
8.Release clip and disconnect hose from heater
rail.

Mpi
13
REPAIR 19.Connect crankshaft sensor, knock sensor, air
conditioning compressor, fuel injector harness,
inlet manifold air temperature and fuel
temperature sensor multiplugs.
20.Connect fuel hose to pressure regulator and
secure with clip.
21.Fit and tighten fuel pipe to fuel rail union.
22.Connect multiplugs to throttle housing.
23.Connect vacuum hose to manifold.
24.Connect oil pressure switch multiplug.
25.Connect brake servo hose to manifold, secure
with clip.
26.Connect throttle cable to cam.
27.Position engine harness and connect breather
hose to inlet manifold, secure with clip.
28.Connect coolant temperature sensor multiplugs,
secure harness with cable tie.
29.Connect oxygen sensor multiplug, secure
harness with cable tie.
30.Connect alternator harness.
31.Connect heater hose to heater rail and secure
with clip.
32.Connect hose to coolant pump and secure with
clip.
33.Connect inlet hose to power steering pump and
secure with clip.
34.Fit and tighten outlet pipe union to power
steering pump.
35.Connect bypass and top hose, secure with clip.
36.Connect air cleaner to throttle housing hose and
secure with clip.
37.Remove engine lifting bracket.
38.Position spark plug cover and secure with
screws.
39.Fill engine with oil.
40.Fit bonnet [hood].
See CHASSIS AND BODY,
Repair, Bonnet [Hood]
41.Fit radiator.See COOLING SYSTEM, Repair,
Radiator - Mpi
42.Adjust throttle cable.See FUEL SYSTEM,
Adjustment, Throttle Cable Adjustment
ENGINE SUMP GASKET
Service repair no - 12.60.43
Remove
1.Drain engine oil.
2.Refit drain plug, use new sealing washer if
necessary, tighten to the correct torque.
3.Remove 18 bolts securing sump.
NOTE: 25mm long bolt is fitted at rear L.H.
corner of sump.
4.Release sump from cylinder block.
5.Discard gasket.

12ENGINE
14
REPAIR Refit
1.Clean sump, remove all traces of gasket from
mating faces of sump and cylinder block.
Visually check sump for damage.
2.Apply beads of RTV sealant to front main
bearing cap.
3.Position new gasket to sump, ensuring that
location pips on gasket are located in sump.
Check gasket lays flat on sump flange.
4.Fit sump. Fit bolts, ensuring that longest bolt is
inserted at position 7.
5.Working around the sump in the sequence
illustrated, tighten the bolts to the stage 1 torque
figure. Then, in the same sequence, tighten the
bolts to the stage 2 torque figure.
NOTE: For torque values.See
Specifications, torque, Torque Values
6.Fill engine with oil.CYLINDER HEAD GASKET
Service repair no - 12.29.01
Remove
1.Disconnect battery negative lead.
2.Position absorbent cloth around fuel pipe to fuel
rail union. Unscrew union to relieve pressure.
CAUTION: Plug the connections.
WARNING: Do not carry out the next
instruction until the coolant is cool to
avoid personal injury from scalding.
3.Release clip and disconnect radiator bottom
hose, allowing coolant to drain into a suitable
container.

Mpi
19
REPAIR CAMSHAFT COVER GASKET
Service repair no - 12.29.40 - Exhaust
Service repair no - 12.29.41 - Inlet
Remove
1.Release 4 screws from spark plug cover.
2.Remove spark plug cover.
Inlet only
3.Release clips and disconnect 2 breather hoses
from camshaft cover.
4.Remove 4 bolts securing support brackets to
manifold and cover.
5.Remove support brackets.
6.Remove 12 bolts from camshaft cover.
Exhaust only
7.Remove 13 bolts from camshaft cover.
Inlet and exhaust
8.Remove camshaft cover assemblies.
9.Remove and discard baffle/gasket plate(s).
Refit
1.Place protective cloth over tappets.
2.Using an M8 x 1,25 mm tap, remove all traces of
sealing compound from camshaft housing bolt
holes.
3.Blow out bolt holes using an airline.
4.Ensure all traces of oil are removed from bolt
holes, remove protective cloth.
5.Clean camshaft cover(s) and mating face of
camshaft housing(s).
6.Position new baffle/gasket plate to camshaft
housing(s).
NOTE: Fit baffle/gasket dry.
7.Fit camshaft cover(s).
Inlet only
8.Position spacers and manifold support brackets.
9.Fit bolts finger tight.
10.Working from the centre outwards, progressively
tighten bolts to torque.
10Nm
11.Tighten support bracket to inlet manifold bolts.
12.Connect breather hoses to camshaft cover.

12ENGINE
20
REPAIR
Exhaust only
13.Fit bolts finger tight.
14.Working from the centre outwards, progressively
tighten bolts to the correct torque.
10Nm
Inlet and exhaust
15.Fit spark plug cover to camshaft cover, tighten
screws.CAMSHAFT DRIVE BELT
Service repair no - 12.65.17
Remove
NOTE: If the timing belt is to be removed
from the camshaft gears only, it is not
necessary to remove the drive belt,
crankshaft pulley or timing belt lower cover.
1.Remove drive belt.
2.Remove 5 bolts securing timing belt top cover.
3.Remove top cover.
4.Remove 5 bolts securing timing belt centre
cover.
5.Remove timing belt centre cover.
6.Rotate crankshaft to align timing marks on
camshaft gears - 90°BTDC.

12ENGINE
22
REPAIR
CAUTION: Ease timing belt off gears using
fingers only. Metal levers may damage the
belt and gears. Do not rotate engine with
timing belt removed and cylinder head fitted.
Timing belts must be stored and handled with
care. Always store a timing belt on its edge with a
bend radius greater than 50 mm. Do not use a
timing belt which has been twisted or bent double
as this can fracture reinforcing fibres. Do not use
an oil contaminated timing belt. Although the belt
has a service life of 96,000 miles, 160,000 km, an
existing belt should only be refitted if it has
completed less than 48,000 miles, 80,000 km.
Refit
NOTE: For torque values.See
Specifications, torque, Torque values
1.Clean timing belt gears and pulleys.
2.Clean crankshaft pulley.
CAUTION: If original belt is to be refitted,
ensure direction of rotation mark is facing
correct way.
3.Fit timing belt to gears, starting at the crankshaft
gear and working in an anti-clockwise direction.
CAUTION: Ensure the belt run between the
crankshaft and exhaust camshaft gear is
kept taut during the fitting procedure.
4.Fit timing belt lower cover, tighten 3 bolts to the
correct torque.
5.Fit crankshaft pulley to crankshaft timing gear.
6.Fit tool LRT-12-059 to crankshaft pulley, fit 2
bolts to retain tool.
7.Fit crankshaft pulley centre bolt, and using tool
LRT-12-059 to restrain pulley, tighten bolt to the
correct torque.
8.Remove tool LRT-12-059
9.Fit bolts securing crankshaft pulley to timing
gear, tighten bolts to the correct torque.
10.Remove tool LRT-12-060.Tension belt
1.Loosen timing belt tensioner pulley bolt.
2.Apply
40Nmanti-clockwise torque to inlet cam
pulley bolt and release.
3.Tighten tensioner pulley bolt to the correct
torque.
4.Remove tool LRT-12-058 from flywheel.
5.Fit timing belt centre cover, tighten 5 bolts to the
correct torque.
6.Fit timing belt upper cover, tighten 5 bolts to the
correct torque.
7.Fit drive belt.

Mpi
23
REPAIR CHECK CAMSHAFT DRIVE BELT
Service repair no - 12.65.17
CAUTION: This check must be carried out
at the service intervals specified and
whenever carrying out any repair which
requires the timing belt to be disturbed. Pay
particular attention for signs of belt splitting at
base of teeth.
1.Remove 5 bolts securing timing belt upper cover
2.Remove upper cover.
3.Using a socket and extension bar on the
crankshaft pulley bolt, rotate engine to allow the
timing belt to be inspected.
CAUTION: Do not use camshaft gears or
retaining bolts to rotate engine.
4.Check timing belt condition, renew any belt that
shows signs of oil contamination, cracking,
fraying or splitting at base of teeth.
CAUTION: Cause of oil contamination, if
present, must be rectified.
5.Clean timing belt upper cover.
6.Position upper cover.
7.Fit upper cover securing bolts.