warning light LAND ROVER DISCOVERY 1995 Workshop Manual

INTRODUCTION
7
INFORMATION DYNAMOMETER TESTING - VEHICLES WITH
ANTI-LOCK BRAKES (ABS)
WARNING: Do not attempt to test ABS
function on a dynamometer
Four wheel dynamometers
NOTE: Before testing a vehicle on a four
wheel dynamometer disconnect the valve
relay.
See Electrical Trouble Shooting
Manual.
The ABS function will not work, the ABS warning
light will illuminate. Normal braking will be
available.
Provided that front and rear rollers are rotating at
identical speeds and that normal workshop safety
standards are applied, there is no speed restriction
during testing except any that may apply to the tyres.
Two wheel dynamometers
IMPORTANT: Use a four wheel dynamometer for
brake testing if possible.
NOTE: ABS will not function on a two
wheel dynamometer. The ABS light will
illuminate during testing. Normal braking
will be available.
If brake testing on a single rig is necessary it must be
carried out with propeller shaft to the rear axle
removed, AND neutral selected in BOTH main and
transfer boxes.
If checking engine performance, the transfer box must
be in high range and drive shaft to stationary axle
removed.
TOWING
CAUTION: The vehicle has permanent
four-wheel drive. The following towing
instructions must be adhered to:
Towing the vehicle on all four wheels with driver
operating steering and brakes.
1.Turn ignition key turn to position '1' to release
steering lock.
2.Select neutral in main gearbox and transfer
gearbox.
3.Secure tow rope, chain or cable to towing eye.
4.Release the parking brake.
CAUTION: The brake servo and power
assisted steering system will not be
functional without the engine running.
Greater pedal pressure will be required to apply
the brakes, the steering system will require
greater effort to turn the front road wheels.
The vehicle tow connection should be used only
in normal road conditions, 'snatch' recovery
should be avoided.
Suspended tow by breakdown vehicle
CAUTION: To prevent vehicle damage,
front or rear propeller shaft MUST BE
removed, dependent upon which axle is
being trailed.
1.Mark propeller shaft drive flanges at transfer
gearbox and axles with identification lines to
enable the propeller shaft to be refitted in its
original position.
2.Remove the propeller shaft fixings, remove the
shaft from the vehicle.
3.If the front axle is to be trailed turn ignition key to
position '1' to release steering lock.
CAUTION: The steering wheel and/or
linkage must be secured in a straight
ahead position. DO NOT use the steering
lock mechanism for this purpose.

01INTRODUCTION
8
INFORMATION TRANSPORTING THE VEHICLE BY TRAILER
Lashing eyes are provided on front and rear of the
chassis side members, to facilitate the securing of the
vehicle to a trailer or other means of transportation.
CAUTION: Underbody components must
not be used as lashing points.
Install vehicle on trailer and apply park brake. Select
neutral in main gearbox. Selecting 'N' will prevent
damage to parking pawl of the automatic gearbox.
FRONT OF CHASSIS
REAR OF CHASSIS
JUMP STARTING
WARNING: Hydrogen and oxygen gases
are produced during normal battery
operation. This gas mixture can explode if
flames, sparks or lighted tobacco are brought
near battery. When charging or using a battery in
an enclosed space, always provide ventilation and
shield your eyes.
Keep out of reach of children. Batteries contain
sulphuric acid. Avoid contact with skin, eyes, or
clothing. Also, shield eyes when working near
battery to protect against possible splashing of
acid solution. In case of acid contact with skin,
eyes, or clothing, flush immediately with water for
a minimum of fifteen minutes. If acid is swallowed,
drink large quantities of milk or water, followed by
milk of magnesia, a beaten egg, or vegetable oil.
SEEK MEDICAL AID IMMEDIATELY.
To Jump Start - Negative Ground Battery
WARNING: To avoid any possibility of
injury use particular care when connecting
a booster battery to a discharged battery.
1.Position vehicles so that jump leads will reach,
ensuring that vehiclesDO NOT TOUCH,
alternatively a fully charged slave battery may be
positioned on floor adjacent to vehicle.
2.Ensuring that ignition and all electrical
accessories are switched off, that parking brake
is applied and neutral is selected on a manual
gearbox, with an automatic gearbox select
neutral (N) or park (P) and then connect the
jump leads as follows;
A.Connect one end of first jumper cable to positive
(+) terminal of booster battery.
B.Connect other end of first jumper cable to
positive (+) terminal of discharged battery.
C.Connect one end of second jumper cable to
negative terminal of booster battery.

INTRODUCTION
11
INFORMATION CROSS REFERENCE OF EMISSION SYSTEM
TERMINOLOGY
NEW TERM (ACRONYM)
Accelerator pedal (AP).................................................
Air cleaner (ACL)..........................................................
Air conditioning (AC)....................................................
Battery positive voltage (B+)........................................
Closed loop (CL)..........................................................
Closed throttle position (CTP)......................................
Canister purge valve (CANPV)....................................
Data link connector (DLC)...........................................
Diagnostic trouble code (DTC).....................................
Distributor ignition (DI).................................................
Engine control module (ECM)......................................
Engine coolant level (ECL)...........................................
Engine coolant temperature (ECT)..............................
Engine coolant temperature sensor (ECTS)................
Engine speed (RPM)....................................................
Evaporative emission system (EVAP)..........................
Engine fuel temperature sensor (EFTS)......................
4th gear, 3rd gear etc. (4GR, 3GR)..............................
Fuel pump (FP)............................................................
Fan control module (FCM)...........................................
Generator (GEN)..........................................................
Ground (GND)..............................................................
Heated oxygen sensor (H02S)....................................
Idle air control (IAC)......................................................
Idle air control valve (IACV).........................................
Ignition control module (ICM).......................................
Inertia fuel shutoff (IFS)................................................
Inertia fuel shutoff switch (IFSS)..................................
Intake air temperature (IAT).........................................
Malfunction indicator lamp (MIL)..................................
Manifold vacuum zone (MVZ)......................................
Mass air flow sensor (MAFS).......................................
Multiport fuel injection (MFI)........................................
On board diagnostic (OBD)..........................................
Open loop (OL)............................................................
Park/neutral position (PNP).........................................
Park/neutral position switch (PNPS)............................
Programmable read only memory (PROM)..................
Relay module (RM)......................................................
Service reminder indicator (SRI)..................................
Solid state relay module (SSRM).................................
Three way catalytic converter (TWC)..........................
Throttle body (TB)........................................................
Throttle position sensor (TPS)......................................
Torque converter clutch (TCC)....................................
Transmission range (TR)..............................................
Transmission range selector (TRS).............................
Vehicle speed sensor (VSS)........................................
Wide open throttle (WOT)............................................OLD TERM (ACRONYM)
Throttle pedal (-)..........................................................
Air cleaner (-)...............................................................
Air conditioning (AC)....................................................
Battery plus, bat +, bat feed (B+).................................
Closed loop (-).............................................................
Closed throttle, idle position (-)....................................
Charcoal canister purge valve (-).................................
Serial link (-)................................................................
Fault code (-)...............................................................
Electronic ignition (-)....................................................
Electronic control unit (ECU)........................................
Coolant level (-)...........................................................
Coolant temperature (temp).........................................
Coolant temperature thermistor (-)..............................
Engine speed (rev/min)................................................
Evaporative loss system (ELC)...................................
Fuel temperature thermistor (-)....................................
Fourth gear, 3rd gear (-)..............................................
Fuel pump (-)...............................................................
Condenser fan timer (-)................................................
Alternator (-)................................................................
Ground, earth (B-)........................................................
Lambda (02) sensor (-)................................................
Idle speed control (ISC)................................................
Stepper motor (-).........................................................
Ignition module (-)........................................................
Inertia switch (-)...........................................................
Inertia switch (-)...........................................................
Intake temperature/ambient temperature (-)................
EFI warning lamp (-)....................................................
Manifold depression, vacuum (-).................................
Air flow meter (-)..........................................................
Electronic fuel injection (EFI).......................................
Fault code display unit (-)............................................
Open loop (-)...............................................................
Park or neutral (-).........................................................
Start inhibit switch (-)...................................................
Chip, PROM (PROM)...................................................
Relay (-).......................................................................
Check engine light (-)...................................................
Control unit (-)..............................................................
Catalyst, catalytic converter (CAT)..............................
Throttle housing (-)......................................................
Throttle potentiometer (-).............................................
Direct drive clutch (DDC)..............................................
Transmission gear (-)...................................................
Shift lever, shifter (-)....................................................
Road speed transducer (-)...........................................
Full throttle, wide open throttle (WOT).........................

GENERAL SPECIFICATION DATA
15
INFORMATION BULBS
REPLACEMENT BULBS TYPE
Exterior lights
Headlamps 12V 60/55W (Halogen)
Headlamps - France amber 12V 60/55W (Halogen)
Auxiliary driving lamps 12V 55W H3 (Halogen)
Sidelamps 12V 5W bayonet
Tail lamps 12V 5/21W bayonet
Reverse lamps 12V 21W bayonet
Stop lamps 12V 21W bayonet
Direction indicator lamps 12V 21W bayonet
Rear side marker lamps 12V 5W capless
Number plate lamps 12V 5W capless
Interior lights
Instrument panel lamps and warning lamps 12V 1.2W bulb/holder unit
Ignition warning lamp (Instrument panel) 12V 2W capless
Interior roof lamps 12V 10W 'Festoon'
Clock illumination 12V 1.2 capless
Cigar lighter illumination 12V 1.2W capless
Door shut face/puddle lamps 12V 5W capless
Auxiliary switch panel illumination (green) 12V 1.2W capless
Heated rear screen warning lamp (amber) 12V 1.2W capless
Hazard warning lamp 12V 1.2W capless
Automatic graphics illumination 12V 5W capless
Heater/air conditioning graphics illumination 12V 1.2W bulb/holder unit
Differential lock warning lamp 12V 1.2W bulb/holder unit
Column switch illumination 12V 1.2W capless
CAUTION: The fitting of new bulbs with wattages in excess of those specified will result in damage
to vehicle wiring and switches.

MAINTENANCE
19
MAINTENANCE
RESET EMISSION MAINTENANCE REMINDER -
USA
The emission maintenance reminder is designed to
activate at 52,500 and 105,000 miles respectively and
will illuminate a 'Service Engine' red warning light in
instrument binnacle.
The emission maintenance reminder must be reset
after required maintenance has been carried out and
a new tamperproof label fitted by a Land Rover of
North America dealer. This emission maintenance
reminder is part of the Emission Control System
Reset
1.The control unit is located in the passenger
footwell.
2.Identify control unit and remove from plug.
3.Remove tamperproof label to reveal access hole
for resetting.
4.Place a thin metallic probe into access hole and
momentarily electrically short between reset pins
inside unit.RECOMMENDED SERVICE ITEMS
Refer Service Schedule sheets for intervals.
Clean sunroof drain tubes, clean and lubricate guide
rails and slides.
Renew the hydraulic brake fluid.
See BRAKES,
Repair, Brake System Bleed
Renew all hydraulic brake fluid, seals, brake servo
filter and flexible hoses.
All working surfaces of the master cylinder and caliper
cylinders should be examined and renewed where
necessary.
ABS vehicles only - renew hydraulic brake fluid and
flexible hoses examine the working surfaces of the
caliper cylinders and renew the seals or cylinders
where necessary.
Air cleaner - When the vehicle is used in dusty or field
conditions or deep wading, frequent attention to the
air cleaner may be required.
ABS vehicles used extensively in arduous off-road
conditions - check the rear wheel road speed sensor
for abrasive wear.

12ENGINE
4
DESCRIPTION AND OPERATION Lubrication system
The V8i full flow lubrication system uses a gear type oil pump which is driven from the front of the crankshaft. The
oil pump gears are housed in the front cover and the pressure relief valve, warning light switch and filter are also
fitted to the front cover.
Oil drawn through the centrally located steel gauze strainer in the sump, is pumped under pressure through oil
cooler located in the lower half of the main coolant radiator. The cooled oil then passes through the filter, before
being distributed from the main gallery via drillings, to the various components in the engine.
Lubrication to the thrust side of the cylinders is by oil grooves machined in each connecting rod big end joint face,
which are timed to align with holes in the big end journals on the power and exhaust strokes.
Lubrication system
1. Oil to cooler
2. Oil from cooler

19FUEL SYSTEM
4
DESCRIPTION AND OPERATION OPERATION
Diesel engines operate by compression ignition. The
rapid compression of air in the cylinder during the
compression cycle heats the injected fuel, causing it
to self ignite. During cold starting, automatically
controlled glow plugs assist in raising the temperature
of the compressed air to ignition point.
A cold start advance unit advances the injection timing
to further assist starting. Idle quality is improved by
the high idle setting.
The engine is supplied with pre-compressed air by a
single stage turbocharger.
Exhaust gases passing over a turbine cause it to
rotate, driving a compressor mounted on the turbine
shaft. Air drawn from the cold air intake passes, via
the air cleaner, to the turbocharger where it is
compressed. The compressed air passes to the
cylinders via an intercooler, which reduces the
temperature of the compressed air, increasing its
density.
Fuel is drawn from the tank by a mechanical lift pump
and passes to the injection pump via a filter. In
addition to removing particle contamination from the
fuel, the filter incorporates a water separator, which
removes and stores both bound and unbound water.
The injection pump meters a precisely timed, exact
quantity of fuel to the injectors in response to throttle
variations, injection timing varying with engine speed.
Any excess fuel delivered to the injection pump is not
injected, passing back to the tank via the fuel return
line.
Fuel is injected in a finely atomised form into a
pre-combustion chamber in the cylinder head where it
ignites. The burning fuel expands rapidly into the main
combustion chamber, creating extreme turbulence
which mixes the burning fuel thoroughly with the
compressed air, providing complete combustion.
Cold Starting is assisted by glow plugs, a cold start
advance unit and a high idle setting.Glow plugs
Glow plug operation is controlled by a timer unit, start
relay and resistor. When the ignition is turned on the
timer unit is energised, the glow plugs start to operate
and a warning light on the dashboard illuminates,
remaining illuminated until the glow plugs are
automatically switched off.
The length of time the glow plugs will operate is
dependent on under bonnet temperature, which is
monitored by a sensor located in the timer unit.
Starting the engine results in the power supply to the
glow plugs passing through the resistor, which
reduces their operating temperature. The glow plugs
are cut out either by the temperature sensor in the
timer, or by a microswitch on the injection pump which
operates when the throttle is depressed.
Cold start advance
The cold start advance unit is connected to the engine
cooling system via hoses. It contains a temperature
sensitive element which is retracted when cold and
pulls the advance lever, via cable, towards the rear of
the pump against spring pressure. As coolant
temperature rises, the cold start element expands
releasing tension on the cable and allowing spring
pressure to move the advance lever forwards.

19FUEL SYSTEM
20
REPAIR ACCELERATOR PEDAL
Service repair no - 18.30.35
Remove
1.Remove lower dash panel.
2.Remove clevis pin securing throttle cable to
accelerator pedal.
3.Release tension from pedal return spring.
4.Remove circlip from pedal pivot pin.
5.Withdraw pivot pin.
NOTE: It may be necessary to lower
steering column to gain access to pivot
pin circlip.
6.Remove accelerator pedal.
Refit
7.Lightly grease pivot and clevis pins.
8.Fit clevis pin using aNEWcotter pin.
9.Reverse removal procedure.FUEL PUMP AND SENDER UNIT
Service repair no - 19.45.03
A plastic fuel tank with a combined fuel pump/sender
unit is fitted. The fuel pump/sender unit is accessed
through a panel in the load space floor.
Fuel pump/sender unit
WARNING: Ensure that fuel handling
precautions given in Section 01 -
Introduction are strictly adhered to when
carrying out following instructions.
CAUTION: Before disconnecting any part
of fuel system, it is imperative that all dust,
dirt and debris is removed from around
components to prevent ingress of foreign matter
into fuel system.
Service Tools:
LRT-19-001 wrench - pump retaining ring
LRT-19-002 'Speedfit' disconnector
Remove
1.Depressurise fuel system.
See Depressurising
Fuel System
2.Disconnect battery negative lead.
3.Syphon at least 9 litres (2 gallons) of fuel from
fuel tank into a suitable container that can be
sealed.
4.Remove carpet from loadspace floor and
tailgate.
5.Fold back loadspace sound insulation to reveal
access panel.

26COOLING SYSTEM
6
REPAIR WATER PUMP
Service repair no - 26.50.01
Remove
WARNING: Disconnect battery negative
terminal to prevent engine being started
before removing or adjusting drive belts.
1.Drain engine cooling system.
See Adjustment,
Coolant
2.Remove fan blades and pulley.See Viscous
Coupling, Fan Blades, Pulley and Fan Cowl
3.Disconnect inlet hose from water pump.
4.Remove water pump bolts.
5.Remove water pump and joint washer.
Refit
6.Lightly grease new joint washer, position on
timing cover.
7.Clean threads of all long bolts and coat with
Loctite 572 thread lubricant-sealant.
8.Locate water pump in position. Tighten
remaining water pump housing bolts evenly to
28 Nm.
9.Reverse removal procedure. 1 to 3.
10.Check for coolant leaks around all hose
connections and joint faces.

41TRANSFER GEARBOX
2
REPAIR Remove
1.Site vehicle on a ramp [hoist].
2.Disconnect battery negative lead.
3.Remove fan cowl from radiator.
4.Remove transfer gear lever knob and gaiter.
5.Raise vehicle on ramp [hoist].
6.Drain oil and refit plug.
7.Detach heat shield at front exhaust pipe to
manifold.
8.Disconnect electrics to Lambda sensors.
9.Remove catalytic converter assembly.
10.Remove chassis crossmember from under
gearbox.
11.Remove heat shield from speedometer cable at
transfer gearbox.
12.Remove clamp and disconnect speedometer
cable from transfer gearbox. Tie cable to one
side.
13.Mark for reassembly then disconnect propeller
shaft to output flange, tie to one side.
14.Repeat on front propeller shaft to output flange.
15.Remove bolts retaining silencer front and rear
securing brackets and tie silencer to one side.
16.Place four 30mm long spacers between top of
hoist and adaptor plate, at securing points, and
secure adaptor plate to hoist.17.Remove four central bolts from transfer gearbox
bottom cover, move hoist into position and
secure adaptor plate to transfer gearbox.
18.Adjust hoist to take weight of transfer gearbox.
19.Remove tie bar, transfer gearbox to main
gearbox.
20.Remove nuts and bolts securing right transfer
gearbox mounting bracket to chassis.
21.Repeat for left mounting bracket. Removal of
these fixings will also free speedometer
transducer bracket.
22.Remove right side mounting bracket to flexible
mounting rubber.
23.Lower hoist until rear brake drum clears
passenger footwell. Check engine does not
crush any components while lowering.
24.Loosen park brake adjustment nut.
25.Remove park brake drum.
26.Remove park brake assembly complete from
rear output flange.
27.Disconnect leads from transfer gearbox
temperature sensor and differential lock warning
light switch.
28.Remove banjo bolt from breather pipe, retrieve
sealing washers and lay pipe aside.
29.Remove split [cotter] pin and washers securing
differential lock to connecting rod and disconnect
rod from lever.
30.Select low range transfer gearbox position.
31.Remove high/low rod lower lock nut and remove
rod from yoke.
32.Position hoist jack channel under bell housing.
33.Using wooden block support the main gearbox
and bell housing.
34.Remove upper and lower bolts securing transfer
gearbox to main gearbox.
35.Fit guide studs 18G 1425 to main gearbox and
move transfer gearbox rearwards to detach.