lock LAND ROVER DISCOVERY 1999 Workshop Manual
[x] Cancel search | Manufacturer: LAND ROVER, Model Year: 1999, Model line: DISCOVERY, Model: LAND ROVER DISCOVERY 1999Pages: 1529, PDF Size: 34.8 MB
Page 544 of 1529
TRANSFER BOX - LT230SE
DESCRIPTION AND OPERATION 41-19
Power flow - transfer box in HIGH ratio
Up to 03 Model Year section shown, from 03MY similar
The gearbox output shaft transmits power to the mainshaft input gear which is in constant mesh with one of the
intermediate gears. The intermediate gears are in constant mesh with the high and low range output gears running
on the differential rear shaft.
Power is transmitted to the output shafts via the differential assembly by locking either the high or low range gears to
the differential rear shaft. This is achieved by means of the high/low selector fork, sleeve and splined hub.
Page 546 of 1529
TRANSFER BOX - LT230SE
ADJUSTMENTS 41-21
ADJUST ME NTS
Cable - selector - differential lock - adjust
$% 41.20.11
Check
1.Check operation of differential lock selection
and adjust cable if required.
Adjust
1.Remove front propeller shaft.
+ PROPELLER SHAFTS, REPAIRS,
Propeller shaft - front.
2.Loosen locknuts securing outer cable to
abutment bracket.
3.Move differential lock selector lever to non
differential lock position.
4.Move differential lever on transfer gearbox fully
forward to rotate selector shaft anti-clockwise
into the non differential lock detent position.
CAUTION: Should the lever move past the
detent, allow it to move back into the non
differential lock detent position before
adjusting the cable.
5.Without moving levers, simultaneously tighten
differential lock outer cable locknuts either side
of the abutment bracket to 30 Nm (22 lbf.ft).
6.Fit front propeller shaft.
+ PROPELLER SHAFTS, REPAIRS,
Propeller shaft - front.
Cable - high/low selector
$% 41.20.46
Adjust
1.Raise vehicle on ramp.
2.Using a suitable crows foot spanner, loosen
lock nuts securing outer cable to abutment
bracket.
3.Select high range by moving lever on transfer
gearbox fully forward.
4.Insert tool LRT-41-016 through hole in selector
lever and housing. This ensures selector
lever is in the high range position.
5.Check that tool LRT-41-016 is a sliding fit in
selector lever and housing.
6.Simultaneously tighten high/low selector cable
lock nuts either side of abutment bracket to 30
Nm (22 lbf.ft) .
7.Remove tool LRT-41-016 from gear selector
lever and housing.
8.Lower vehicle on ramp.
Page 549 of 1529
TRANSFER BOX - LT230SE
41-24 REPAIRS
Cable - selector - differential lock
$% 41.20.12
Remove
1.Remove centre console.
+ INTERIOR TRIM COMPONENTS,
REPAIRS, Console - centre - automatic
models.
2.Remove 4 bolts securing transfer gearbox high/
low selector lever to transmission tunnel.
3.Remove front propeller shaft.
+ PROPELLER SHAFTS, REPAIRS,
Propeller shaft - front.
4. Models fitted with high/low shift interlock
solenoid: Release interlock solenoid multiplug
and disconnect multiplug from main harness.
5. Models fitted with high/low shift interlock
solenoid: Remove sleeve retaining rings and
remove sleeve from high/low select cable.
6.Release and remove clevis pin and 'C' clip
securing transfer gearbox high/low selector
cable to transfer gearbox high/low selector
lever. Position the cable aside.7.Release and remove clevis pin securing
differential lock selector cable to transfer
gearbox.
8.Loosen locknuts securing differential lock
selector cable to differential lock selector cable
abutment bracket.
9.Release and remove differential lock selector
cable from differential lock selector cable
abutment bracket.
10.Remove transfer gearbox high/low selector
lever assembly from transmission tunnel.
11.Release and remove clevis pin and 'C' clip
securing differential lock selector cable to
differential lock selector lever. Remove the
differential lock selector cable.
Page 550 of 1529
TRANSFER BOX - LT230SE
REPAIRS 41-25
Refit
1.Fit differential lock selector cable to differential
lock selector lever and secure with clevis pin
and 'C' clip.
2.Position transfer gearbox high/low selector
lever assembly to transmission tunnel.
3.Position differential lock selector cable to
differential lock selector cable abutment
bracket and tighten locknuts sufficiently to
retain cable.
4.Fit differential lock selector cable to transfer
gearbox and secure with clevis pin.
5.Fit transfer gearbox high/low selector cable to
transfer gearbox high/low selector lever and
secure with clevis pin and 'C' clip.
6.Fit transfer gearbox high/low selector lever to
transmission tunnel, fit bolts and tighten to 10
Nm (7 lbf.ft).
7. Models fitted with high/low shift interlock
solenoid: Position interlock solenoid harness
to high/low shift cable, fit sleeve around cable
and harness and secure sleeve.
8. Models fitted with high/low shift interlock
solenoid: Connect solenoid multiplug to main
harness and secure multiplug to bracket.
9.Check and adjust differential lock selector
cable.
+ TRANSFER BOX - LT230SE,
ADJUSTMENTS, Cable - selector -
differential lock - adjust.
10.Fit centre console.
+ INTERIOR TRIM COMPONENTS,
REPAIRS, Console - centre - automatic
models.
Transfer box - Diesel
$% 41.20.25.99
Remove
1.Remove front exhaust pipe.
+ MANIFOLDS AND EXHAUST
SYSTEMS - Td5, REPAIRS, Pipe - front.
2.Raise vehicle on ramp.
3.Drain transfer box oil.
+ MAINTENANCE, PROCEDURES,
Transfer box.
4.Remove 3 nuts securing intermediate silencer
to tail pipe.
5.Release silencer from mounting rubbers.
6.Remove silencer and discard gasket.
7.Remove front propeller shaft.
+ PROPELLER SHAFTS, REPAIRS,
Propeller shaft - front.
8.Remove rear propeller shaft.
+ PROPELLER SHAFTS, REPAIRS,
Propeller shaft - rear.
Page 551 of 1529
TRANSFER BOX - LT230SE
41-26 REPAIRS
9.Remove handbrake drum retaining screw and
remove drum.
10.Remove 4 bolts from handbrake back plate,
release back plate and tie aside.
11. Models fitted with high/low shift interlock
solenoid: Release interlock solenoid multiplug
and disconnect multiplug from main harness.
12. Models fitted with high/low shift interlock
solenoid: Remove sleeve retaining rings and
remove sleeve from high/low selector cable.
13. If fitted: Release and remove clevis pin
securing differential lock selector cable to
transfer gearbox.14. If fitted: Loosen locknuts securing differential
lock selector cable to differential lock selector
cable abutment bracket.
15. If fitted: Release and remove differential lock
selector cable from differential lock selector
cable abutment bracket.
16.Remove clevis pin securing high/low ratio
selector cable to selector lever, remove 'C' clip
and release outer cable from abutment bracket.
17. Up to 03 Model Year - if fitted: Disconnect 2
Lucars from differential lock switch and
multiplugs from high/low ratio switch and
neutral sensor.
18.Disconnect multiplug from reverse light switch.
Page 552 of 1529
TRANSFER BOX - LT230SE
REPAIRS 41-27
19. 03 Model Year onwards - if fitted: Release
and disconnect both differential lock warning
lamp switch multiplugs from main harness.
20.Remove cable tie and multi plug from bracket
on transfer box.
21.Release transfer box breather pipe from
bulkhead clip.
22.Remove 4 bolts from transfer box bottom plate,
position support plate LRT-99-010 to transfer
box and tighten bolts. 23.Position gearbox support jack and secure
support plate to jack using 4 bolts.
24.Remove 3 bolts securing transfer box to
gearbox.
25.Fit 3 guide studs LRT-41-009 through
transfer box bolt holes to support it during
removal.
26.Remove 2 bolts and nut securing transfer box
to gearbox.
CAUTION: If securing stud is removed
during this operation, it must be discarded
and a new stud fitted.
27.Position a jack to support gearbox and engine.
Page 553 of 1529
TRANSFER BOX - LT230SE
41-28 REPAIRS
28.Remove 4 bolts and nut, remove gearbox RH
mounting.
29.With assistance, remove transfer box from
gearbox.
30.Remove input shaft oil seal.
+ TRANSFER BOX - LT230SE,
REPAIRS, Oil seal - input shaft.
Refit
1.Fit new input shaft oil seal.
+ TRANSFER BOX - LT230SE,
REPAIRS, Oil seal - input shaft.
2.Clean transfer box to gearbox mating faces.
3.Raise transfer box on jack and align to guide
studs LRT-41-009.
4.Clean transfer box to gearbox bolt threads.
5.Apply sealant, Part No. STC 50552 to bolt and
stud threads.
6.Fit and lightly tighten 2 bolts and nut securing
transfer box to gearbox. If new stud is to be
fitted, apply sealant, Part No. STC 50552 to
stud threads and tighten to 45 Nm (33 lbf.ft).
7.Remove guide studs, fit and lightly tighten
remaining 3 bolts.
8.Tighten bolts and nut by diagonal selection to
45 Nm (33 lbf.ft).
9.Position gearbox RH mounting and tighten
bolts to 85 Nm (63 lbf.ft).
10.Tighten gearbox RH mounting nut to 48 Nm
(35 lbf.ft).
11.Remove 4 bolts securing support plate to
gearbox jack.
12.Remove 4 bolts securing support plate LRT-99-
010 to transfer box and remove plate.
13.Clean bottom plate bolt threads.
14.Apply sealant, Part No. STC 50552 to threads
of 4 bottom plate bolts.
15.Fit 4 bolts securing bottom plate to transfer box
and tighten to 25 Nm (18 lbf.ft).
16.Position breather pipe and secure to bulkhead
clip.
17.Connect multiplug to reverse light switch. 18. Up to 03 Model Year - if fitted : Connect
Lucars to differential lock switch and multiplugs
to high/low ratio switch and neutral sensor.
19. 03 Model Year onwards - if fitted: Connect
differential lock warning lamp multiplugs,
secure harness.
20.Position high/low ratio selector cable and
secure with clevis pin and 'C' clip.
21.Position differential lock selector cable to
differential lock selector cable abutment
bracket and tighten locknuts sufficiently to
retain cable.
22. If fitted: Fit differential lock selector cable to
transfer gearbox and secure with clevis pin.
23. If fitted: Adjust differential lock selector cable.
+ TRANSFER BOX - LT230SE,
ADJUSTMENTS, Cable - selector -
differential lock - adjust.
24. Models fitted with high/low shift interlock
solenoid: Position interlock solenoid harness
to high/low shift cable, fit sleeve around cable
and harness; secure sleeve.
25. Models fitted with high/low shift interlock
solenoid: Connect solenoid multiplug to main
harness and secure multiplug to bracket.
26.Clean handbrake and mating face.
27.Position handbrake back plate and tighten
bolts to 75 Nm (55 lbf.ft).
28.Clean handbrake drum.
29.Fit handbrake drum and tighten retaining
screw.
30.Fit front propeller shaft.
+ PROPELLER SHAFTS, REPAIRS,
Propeller shaft - front.
31.Fit rear propeller shaft.
+ PROPELLER SHAFTS, REPAIRS,
Propeller shaft - rear.
32.Clean exhaust silencer and mating face.
33.Position silencer, fit new gasket , connect
mounting rubbers and tighten nuts to 40 Nm
(30 lbf.ft).
34.Refill transfer box with oil.
+ MAINTENANCE, PROCEDURES,
Transfer box.
35.Fit front exhaust pipe.
+ MANIFOLDS AND EXHAUST
SYSTEMS - Td5, REPAIRS, Pipe - front.
Page 554 of 1529
TRANSFER BOX - LT230SE
REPAIRS 41-29
Transfer box - V8
$% 41.20.25.99
Remove
1.Remove front exhaust pipe.
+ MANIFOLDS AND EXHAUST
SYSTEMS - V8, REPAIRS, Front pipe.
2.Drain transfer box oil.
+ MAINTENANCE, PROCEDURES,
Transfer box.
3.Remove 8 bolts securing rear cross member
and remove cross member.
4.Remove 3 nuts securing intermediate silencer
to tail pipe.
5.Release silencer from mounting rubbers,
remove silencer and discard gasket.
6.Remove front propeller shaft.
+ PROPELLER SHAFTS, REPAIRS,
Propeller shaft - front.
7.Remove rear propeller shaft.
+ PROPELLER SHAFTS, REPAIRS,
Propeller shaft - rear.8.Remove handbrake drum retaining screw and
remove handbrake drum.
9.Remove 4 bolts from handbrake back plate,
release back plate and tie aside.
10. Models fitted with high/low shift interlock
solenoid: Release interlock solenoid multiplug
and disconnect multiplug from main harness.
11. Models fitted with high/low shift interlock
solenoid: Remove sleeve retaining rings and
remove sleeve from high/low selector cable.
Page 555 of 1529
TRANSFER BOX - LT230SE
41-30 REPAIRS
12. If fitted: Release and remove clevis pin
securing differential lock selector cable to
transfer gearbox.
13. If fitted: Loosen locknuts securing differential
lock selector cable to differential lock selector
cable abutment bracket.
14. If fitted: Release and remove differential lock
selector cable from differential lock selector
cable abutment bracket.
15.Remove clevis pin and 'C' clip securing high/
low ratio selector cable to selector lever and
release cable from abutment bracket.
16.Remove 2 cable ties securing cable to fuel
pipes. 17. If fitted: Disconnect 2 Lucars from oil
temperature sensor and disconnect reverse
lamp switch multiplug.
18.Remove banjo bolt securing breather pipe and
discard washers.
19. Up to 03 Model Year - if fitted: Disconnect 2
Lucars from differential lock switch and
multiplugs from high/low ratio switch and
neutral sensor.
20.Disconnect multiplug from reverse light switch.
Page 556 of 1529
TRANSFER BOX - LT230SE
REPAIRS 41-31
21. 03 Model Year onwards - if fitted: Release
and disconnect both differential lock warning
lamp switch multiplugs from main harness.
22.Remove 4 bolts from transfer box bottom plate,
position support plate LRT-99-010 to transfer
box and tighten bolts.
23.Position gearbox support jack and secure
support plate to jack using 4 bolts. 24.Remove 3 bolts securing transfer box to
gearbox.
25.Fit 3 guide studs LRT-41-009 through transfer
box bolt holes to support it during removal.
26.Remove 2 bolts and nut securing transfer box
to gearbox case.
CAUTION: If securing stud is removed
during this operation, it must be discarded
and a new stud fitted.
27.Position a jack to support gearbox and engine.
28.Remove 4 bolts and nut securing RH mounting
to body and transfer box.
29.Remove nut securing LH mounting to body.
30.Raise gearbox and remove RH mounting.
31.With assistance, remove transfer box from
gearbox.
32.Remove input shaft oil seal.
+ TRANSFER BOX - LT230SE,
REPAIRS, Oil seal - input shaft.