fuel LAND ROVER DISCOVERY 2002 Service Manual

ENGINE - TD5
REPAIRS 12-1-47
Engine and ancillaries
$% 12.41.01
Remove
1.Remove bonnet.

+ EXTERIOR FITTINGS, REPAIRS,
Bonnet.
2.Remove underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
3.Drain engine oil.

+ MAINTENANCE, PROCEDURES,
Engine oil - diesel engine.
4.Remove radiator.

+ COOLING SYSTEM - Td5, REPAIRS,
Radiator.
5.Remove turbocharger.

+ ENGINE MANAGEMENT SYSTEM -
Td5, REPAIRS, Turbocharger.
6.Release clips and disconnect heater hoses
from fuel cooler and coolant rail.
7.Release clip and disconnect expansion tank
coolant hose from fuel cooler.
8.Disconnect fuel hoses, tank to fuel cooler and
connector block on cylinder head.
CAUTION: Always fit plugs to open
connections to prevent contamination.9.Disconnect fuel hose from fuel cooler and
secure to connector block on cylinder head.
This is to prevent contamination of the fuel
injection system.
10.Release servo vacuum pipe from clip on fuel
cooler and release hose from vacuum pump.
11.Release expansion tank from body mounting,
release clip, disconnect hose and remove tank.

ENGINE - TD5
12-1-52 REPAIRS
5.Fit 2 upper bolts securing engine oil cooler pipe
and gearbox housing to engine and tighten to
50 Nm (37 lbf.ft) .
6.Lower engine onto mountings, and tighten nuts
to 85 Nm (63 lbf.ft) .
7.Remove tool LRT-12-138 from engine.
8.Fit and tighten bolt securing engine closing
panel to gearbox.
9.Raise vehicle on ramp.
10.Fit nuts and bolts securing engine LH and RH
mountings to chassis and tighten to 85 Nm (63
lbf.ft).
11.Fit remaining bolts securing gearbox housing to
engine and tighten to 50 Nm (37 lbf.ft).
12.Rotate crankshaft and align drive plate to
torque converter.
13.Using a magnetic socket, fit and tighten new
torque converter drive plate bolts to 50 Nm (37
lbf.ft) .
14.Fit front cross member and tighten bolts to 26
Nm (19 lbf.ft).
15.Align gearbox oil cooler pipes.
16.Fit oil cooler pipe clip and tighten bolts to 9 Nm
(7 lbf.ft).
17.Position gearbox oil cooler pipe clamps and
tighten nuts.
18.Position coolant rail and secure support bracket
in engine LH and RH mounting brackets.
19.Fit starter motor.

+ CHARGING AND STARTING,
REPAIRS, Starter motor - diesel.
20.Lower ramp.
21.Position coolant rail to front chassis member, fit
and tighten bolt to 10 Nm (7 lbf.ft).
22.Connect heater hose to coolant rail and secure
with clip.
23.Connect hose to coolant pump and secure with
clip.
24.Position PAS pump and tighten bolts to 25 Nm
(18 lbf.ft).
25.Position PAS pump pulley and lightly tighten
bolts.
26.Position ACE pump, fit bolts and tighten to 25
Nm (18 lbf.ft).
27.Position A/C compressor, fit bolts and tighten
to 25 Nm (18 lbf.ft).
28.Position ancillary drive belt, rotate tensioner
anti-clockwise and locate belt to pulleys.
29.Tighten PAS pump pulley bolts to 10 Nm (7
lbf.ft).
30.Position air intake hose to air cleaner and
secure clips.
31.Position engine harness and connect
multiplugs to compressor, MAF sensor,
turbocharger boost solenoid, AAP & IAT
sensor.
32.Position air inlet hose to turbocharger and
tighten clip. 33.Connect hoses to turbocharger boost solenoid
and secure clips.
34.Clean CKP sensor and mating face.
CAUTION: If originally fitted: Fit spacer to
CKP sensor.
35.Using new 'O' ring, fit CKP sensor, tighten CKP
sensor bolt to 9 Nm (7 lbf.ft) and connect
multiplug.
36.Connect multiplug to EGR modulator.
37.Connect engine earth lead to battery earth lead
and tighten bolt.
38.Connect engine harness multiplug to ECM and
main harness.
39.Connect engine harness multiplugs to fuse
box.
40.Position glow plug lead to fusebox and secure
with bolt.
41.Position battery and alternator leads to fusebox
and secure with bolts.
42.Fit engine compartment fuse box cover.
43.Connect vacuum hose to EGR valve.
44.Connect hose to vacuum pump and secure
vacuum pipe to fuel cooler.
45.Disconnect fuel hose from connector block and
connect to fuel cooler.
46.Connect fuel hoses to fuel cooler and
connector block on cylinder head.
47.Position expansion tank, connect hose and
secure with clip. Secure tank to body mounting.
48.Connect coolant hoses to fuel cooler and
coolant rail and secure clips.
49.Fit turbocharger.

+ ENGINE MANAGEMENT SYSTEM -
Td5, REPAIRS, Turbocharger.
50. Fit radiator.

+ COOLING SYSTEM - Td5, REPAIRS,
Radiator.
51.Fill engine with oil.

+ MAINTENANCE, PROCEDURES,
Engine oil - diesel engine.
52.Fit underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
53.Fit bonnet.

+ EXTERIOR FITTINGS, REPAIRS,
Bonnet.

ENGINE - TD5
12-1-54 REPAIRS
Mounting - front - RH
$% 12.45.03
Remove
1.Remove fixings and remove engine acoustic
cover.
2.Release fixings and remove battery cover.
3.Disconnect battery earth lead.
4.Raise front of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
5.Remove 4 bolts and move fuel cooler to one
side.
6.Fit suitable lifting chains to support engine.
7.With assistance remove 2 bolts securing
engine mounting to chassis.
8.Remove 4 bolts securing engine mounting
bracket to cylinder block.
9.Remove nut securing mounting to mounting
bracket.
10.Remove mounting and mounting bracket. Refit
1.Fit mounting and mounting bracket.
2.Fit front RH engine mounting bracket to
cylinder block and tighten bolts to 48 Nm (35
lbf.ft).
3.With assistance, fit front RH mounting to
chassis and tighten bolts to 85 Nm (63 lbf.ft).
4.Fit front RH mounting to mounting bracket and
tighten nut to 85 Nm (63 lbf.ft).
5.Remove engine support chains.
6.Position Fuel cooler to inlet manifold and
tighten bolts to 25 Nm (18 lbf.ft).
7.Remove stand(s) and lower vehicle.
8.Connect battery earth lead.
9.Fit battery cover and secure with fixings.
10.Fit engine acoustic cover and secure with
fixings.

ENGINE - TD5
OVERHAUL 12-1-69
OVERHAUL
Gasket - inlet manifold
$% 30.15.08.01
Disassembly
Note: The following procedures cover engines
fitted with or without an EGR cooler. The EGR
cooler is bolted to the front of the cylinder head.
EU3 Engine in main illustration, Pre EU3 condition
shown in inset
1.Remove and discard 2 Allen screws securing
EGR pipe to exhaust manifold or EGR cooler.
2. Remove bolt securing EGR pipe to cylinder
head, (if fitted)
3.Disconnect multiplug from IAT and MAP
sensor.
4.Remove 4 bolts securing fuel cooler to inlet
manifold. and remove cooler.
5.Remove bolt securing engine dipstick tube to
camshaft carrier.
6.Release and remove engine dipstick tube.
7.Remove 'O' ring from dip stick tube.
8.Disconnect 4 leads from glow plugs.
9. Remove 2 bolts securing alternator strap
bracket, remove bracket, (if fitted)
10.Remove 2 nuts and 8 bolts and remove inlet
manifold.
11.Remove manifold gasket. Reassembly
1.Clean inlet manifold and mating face, clean
mating faces of EGR pipe, exhaust manifold or
EGR cooler – if fitted.
2.Fit new gasket.
3.Position inlet manifold and working from the
centre outwards, fit inlet manifold nuts and
bolts and tighten to 25 Nm (18 lbf.ft) .
4. Fit alternator strap bracket and tighten bolts to
25 Nm (18 lbf.ft), (if fitted)
5.Connect glow plug leads.
6.Clean engine dipstick tube.
7.Fit new 'O' ring to dipstick tube.
8.Fit engine dipstick tube to camshaft carrier and
tighten bolt to 10 Nm (7 lbf.ft).
9.Position fuel cooler and tighten bolts to 25 Nm
(18 lbf.ft).
10.Connect multiplug to IAT and MAP sensor.
11.Position EGR pipe to exhaust manifold or EGR
cooler and using new Allen screws tighten to 10
Nm (7 lbf.ft).
12. Fit EGR pipe clamp to cylinder head, (if fitted)
and tighten bolt to 10 Nm (7 lbf.ft).

ENGINE - TD5
OVERHAUL 12-1-73
11.Ensure engine is set to TDC firing - No.1
cylinder.
12.Check that mark on camshaft sprocket is
positioned between the 2 coloured links on
timing chain.
13.Position sprocket to camshaft, fit and lightly
tighten 3 new bolts then loosen bolts half a
turn.
14.Clean fixed guide Allen screw and apply
Loctite 242 to screw threads.
15.Fit fixed timing chain guide Allen screw and
tighten to 25 Nm (18 lbf.ft).
16.Clean timing chain tensioner and fit new
sealing washer.
17.Fit timing chain tensioner and tighten to 45 Nm
(33 lbf.ft).
18.Tighten camshaft sprocket bolts to 37 Nm (27
lbf.ft).
19.Remove tool LRT-12-058 from camshaft.
20.Lubricate a new 'O' ring with engine oil and fit to
camshaft sprocket access plug.21.Fit camshaft sprocket access plug.
22.Clean alternator/vacuum pump oil hose union.
23.Lubricate a new 'O' ring with engine oil and fit to
alternator/vacuum pump oil hose union.
24.Fit and tighten alternator/vacuum pump oil
hose union to 10 Nm (7 lbf.ft).
25.Fit bolt securing alternator strap bracket to
cylinder head and tighten to 25 Nm (18 lbf.ft).
26.Connect multiplugs to ECT sensor and EUI's.
CAUTION: Following cylinder head
overhaul, it will be necessary, before fitting
the camshaft cover to adjust the fuel
injector rockers using the following
procedures:
27.Rotate engine clockwise until No.1 EUI lobe is
at full lift.
28.Tighten No.1 rocker adjusting screw until the
EUI plunger is felt to 'bottom out'.
29.Loosen rocker adjusting screw 1 complete turn
to give EUI plunger the required bump
clearance and tighten rocker adjusting screw
to 16 Nm (12 lbf.ft).
CAUTION: Ensure screw does not turn as
locknut is tightened.
30.Carry out the above procedures for the
remaining 4 rocker arms.
31.After completion of rocker adjustment, slowly
rotate engine clockwise 2 complete turns by
hand to ensure that no EUI's are bottoming out
on their plungers.
32.Clean camshaft cover and mating face.
33.Fit new sealing washers and isolators as
necessary to camshaft cover.
34.Fit new camshaft cover gasket to cover.
CAUTION: Gasket must be fitted dry.

ENGINE - TD5
12-1-74 OVERHAUL
35.Fit camshaft cover to camshaft carrier, fit bolts
and working from the centre outwards tighten
bolts to 10 Nm (7 lbf.ft).
36.Fit inlet manifold gasket.

+ ENGINE - Td5, OVERHAUL, Gasket
- inlet manifold.
37.Fit exhaust manifold gasket.

+ ENGINE - Td5, OVERHAUL, Gasket
- exhaust manifold.
38. EGR cooler fitted: Position EGR pipe to
cooler, fit new Allen screws and tighten to 10
Nm (7 lbf.ft)
Cylinder head - overhaul
$% 12.29.19.01
Disassembly
1.Remove cylinder head gasket. Due to the
design of the cylinder head, which
incorporates drillings for the fuel injection
system, it is important that absolute
cleanliness is adhered to when carrying out
any work to the cylinder head.

+ ENGINE - Td5, OVERHAUL, Gasket
- cylinder head.
2.Note the gasket thickness indicator and ensure
the same thickness gasket is used on refitment
of cylinder head.
CAUTION: If new pistons, connecting rods
or crankshaft are to be fitted, it will be
necessary to measure piston stand proud in
order to determine thickness of gasket
required – See Pistons, Connecting rods
and Cylinder Bores – Cylinder head gasket
selection.
3.Remove 4 glow plugs.
4.Disconnect multiplugs from EUI's and remove
harness from camshaft carrier. Remove and
discard 'O' ring from harness multiplug.

ENGINE - TD5
12-1-76 OVERHAUL
16.Using tool LRT-12-034 compress valve
spring.
17.Remove 2 collets from valve stem using a stick
magnet.
18.Remove tool LRT-12-034 .
19.Remove valve spring cap, valve spring and
valve. Keep components in their fitted
order.
20.Using tool LRT-12-071, remove and discard
valve stem oil seal. 21.Repeat above operations to remove remaining
valves. Keep components in their fitted
order.
22. Engine Serial No. Prefixes 15P to
19P:Disconnect spill return pipe from cylinder
head and fuel connector block, remove and
discard 'O' rings.

ENGINE - TD5
OVERHAUL 12-1-77
23.Remove 3 bolts and remove fuel connector
block from cylinder head.
24.Remove gasket, discard 'O' ring and fuel filter.
25. If fitted: Remove spacer block and gasket.
Inspect
1.Thoroughly clean cylinder head mating faces,
ensure that EUI drillings, oil and coolant
passages are clear and bolt holes are clean
and dry.
2.Using suitable solvent, remove all traces of
sealant and gasket material.
CAUTION: Do not use metal scrapers.
3.Remove all traces of oil from camshaft bearings
and journals.
4.Clean glow plug threads.
5.Check core plugs for signs of leakage and
corrosion, seal replacement plugs with Loctite
243.6.Check cylinder head for warping across centre
and from corner to corner:
l Maximum cylinder head warp = 0.1 mm
(0.004 in)
Cylinder heads must not be refaced.
Replace the head assembly if warping
exceeds the limit.
7.Check lash adjuster bores for scoring and signs
of wear or damage.
8.Check lash adjusters for signs of wear, scoring
and overheating, replace as necessary.
Ensure oil hole in each lash adjuster is clear.
Store lash adjusters upright and in their
fitted order.
9.Check finger followers for wear and that rollers
are free to rotate. Store finger followers in
their fitted order.
10.Check camshaft lobes and bearing journals for
signs of scoring and wear.
11.Check bearing surfaces in cylinder head and
camshaft carrier for signs of scoring and wear.
Cylinder head and camshaft carrier are
machined together as an assembly. If
bearing surfaces in either component are
damaged, both components must be
replaced as an assembly.
12.Check camshaft end-float using following
procedures.
13.Position camshaft in camshaft carrier.

ENGINE - TD5
OVERHAUL 12-1-83
9.Using tool LRT-12-154/3, fit new sealing
washer to each injector.
10.Support each end of cylinder head on blocks of
wood ensuring blocks are clear of valves.
11.Position reaction posts in their original fitted
order.
12.Carefully fit EUI's, ensuring they are in their
original fitted order and that each retainer is
located on its dowel.
CAUTION: If new EUI's are fitted, ensure
replacements are correct. Engine Serial No.
Prefixes 10P to 14P – Push rod bushes are
coloured BLACK or BLUE. Serial No.
Prefixes 15P to 19P – Push rod bushes are
coloured GREEN.
13.Fit new retainer bolts and tighten to 32 Nm (24
lbf.ft).
If new injectors are fitted they must be
programmed for use with the ECM using
TestBook.
14.Lubricate lash adjusters and bores with engine
oil.
15.Fit lash adjusters ensuring they are in their
original fitted order.
16.Lubricate finger followers with engine oil.
17.Fit finger followers ensuring they are in their
original fitted order.
18.Lubricate cams and bearing journals on
camshaft, cylinder head and camshaft carrier
with engine oil.
19.Position camshaft in cylinder head with the
timing pin hole in the vertical position.20.Apply an even film of sealant, Part No. STC
4600 to camshaft carrier face and spread to an
even film using a roller.
CAUTION: Ensure sealant does not block
oilways (arrowed) or contaminate camshaft
bearings. Assembly and bolt tightening
must be completed within 20 minutes of
applying sealant.
21.Fit camshaft carrier ensuring it is correctly
located on dowels.
22.Fit and lightly tighten new camshaft carrier
bolts.
23.Using sequence shown, progressively tighten
bolts to 25 Nm (18 lbf.ft).
24.Lubricate a new camshaft rear oil seal with
engine oil, fit seal using a suitable mandrel.
25.Position rocker shaft on camshaft carrier
ensuring rocker shaft is located on dowel.
26.Fit new rocker shaft retaining bolts and working
from the centre outwards, tighten rocker shaft
bolts to 32 Nm (24 lbf.ft).
27.Fit injector harness and connect multiplugs.
28.Clean fuel connector block and mating face.
29.Lubricate a new fuel filter 'O' ring with engine
oil.

ENGINE - TD5
12-1-84 OVERHAUL
30.Fit new fuel filter, 'O' ring, and gasket.
CAUTION: Gasket must be fitted dry.
31. If fitted: Fit fuel connector spacer block and
gasket.
32.Fit fuel connector block, fit bolts and tighten to
25 Nm (18 lbf.ft).
33.Clean glow plugs.
34.Fit glow plugs to cylinder head and tighten to
16 Nm (12 lbf.ft).
35.Fit new cylinder head gasket.

+ ENGINE - Td5, OVERHAUL, Gasket
- cylinder head.
36. Engine Serial No. Prefixes 15P to
19P:Lubricate new 'O' rings with engine oil and
fit to spill return pipe, fit pipe and tighten
connectors to 20 Nm (15 lbf.ft).
37.Before fitting the camshaft cover, the fuel
injector rockers must be adjusted following the
procedures given in Cylinder head gasket -
Refit.

+ ENGINE - Td5, OVERHAUL, Gasket
- cylinder head.
Gasket - engine sump
$% 12.60.38.01
Disassembly
1.Remove 2 bolts securing centrifuge oil drain
pipe to sump, remove and discard gasket.
2.Using sequence shown and noting their fitted
positions, remove 20 bolts securing sump to
cylinder block.
3.Release sump from locating dowels, remove
sump; remove and discard gasket.
Reassembly
1.Clean sump and mating faces, ensure bolt
holes in cylinder block are clean and dry.
2.Using suitable solvent, remove all traces of
sealant from joint faces of timing chain cover
and crankshaft rear oil seal housing.
3.Clean centrifuge oil drain pipe and mating
faces.