Camshaft LAND ROVER FREELANDER 2001 Workshop Manual

MANIFOLDS & EXHAUST SYSTEMS - K SERIES KV6
30-3-30 OVERHAUL
Refit
1.Clean seal faces on inlet manifold chamber and
inlet manifolds.
2.Fit new 'O' rings to RH inlet manifold and new
seals to inlet manifold chamber.
3.Fit inlet manifold chamber to inlet manifolds
and tighten bolts to 18 Nm (13 lbf.ft).
4.Align inlet manifold chamber support brackets
to RH camshaft cover, fit and tighten bolts to 10
Nm (7 lbf.ft).
5.Position engine harness brackets to inlet
manifold chamber, fit and tighten screws.
6.Secure RH plug top coil harness to manifold
chamber support brackets.
7.Connect multiplugs to plug top coils and secure
with locking clips.
8.Connect multiplugs to VIS motors.
9. NAS models: Align harness and fuel feed pipe.
Secure harness and pipe in clip on manifold
chamber.
10. NAS models: Using a new clip, fit intake hose
to throttle body and secure hose with clip.
11. NAS models: Connect multiplug to throttle
body.
12. NAS models: Connect multiplugs to IAT and
MAF sensors.13. NAS models: Fit vacuum/breather pipe and
connect to LH camshaft cover, RH camshaft
cover link pipe and inlet manifold chamber.
14. NAS models: Using a new clip, fit vacuum/
breather pipe to engine air intake hose and
secure pipe with clip.
15. NAS models: Connect vacuum/breather pipe
to LH and RH camshaft covers. Fit pipe into
clip.
16. Non NAS models: Fit vacuum/breather pipe to
throttle body and connect pipe to LH and RH
camshaft covers.
17. Non NAS models: Fit vacuum/breather pipe to
purge control valve and LH camshaft cover.
Using a new clip, connect pipe to 'T' piece and
secure pipe with clip.
18. Non NAS models: Connect multiplug to TP
sensor.
19. Non NAS models: Connect multiplug to IACV.
20. Non NAS models: Connect vacuum pipe to
IACV.
21. Non NAS models: Connect small vacuum pipe
to purge control valve..
22.Connect multiplug to purge control valve .
23.Fit vacuum enhancer and connect to inlet
manifold chamber.
24.Using a new clip, connect vacuum enhancer to
intake hose and secure hose with clip.

AUTOMATIC GEARBOX - JATCO
44-12 REPAIRS
Gearbox - KV6 - with engine and gearbox
removed
$% 44.20.01.99
Remove
1.Release HO2S multiplug from support bracket
on LH camshaft cover, disconnect multiplug.
2.Remove 4 nuts securing LH exhaust manifold
to cylinder head.
3.Remove exhaust manifold, remove and discard
gasket.4.Remove nut securing manifold heat shield to
IRD unit.
5.Remove nut securing heat shield to IRD pinion
housing.
6.Remove 2 bolts securing heat shield and
remove heat shield.
7.Disconnect breather hose from IRD housing.
8.Release clips and disconnect coolant hoses
from IRD.

AUTOMATIC GEARBOX - JATCO
REPAIRS 44-19
16.Remove 2 bolts securing gearbox to engine.
17.Release HO2S multiplug from support bracket
on LH camshaft cover, disconnect multiplug.
18.Remove 4 nuts securing LH exhaust manifold
to cylinder head.
19.Remove exhaust manifold, remove and discard
gasket.
20.Position container to collect fluid spillage.21.Disconnect 2 fluid cooler hose unions and
discard 'O' rings.
CAUTION: Always fit plugs to open
connections to prevent contamination.
22.Remove 3 bolts securing fluid cooler bracket.
23.Move fluid cooler aside.
24.Remove bolt securing CKP sensor to gearbox,
release sensor and position aside.
M44 1651M44 1639
M44 1665

BRAKES
70-20 REPAIRS
Vacuum pump - Td4 - manual
$% 70.50.19
Remove
1.Disconnect battery earth lead.
2.Remove air cleaner element.

+ FUEL DELIVERY SYSTEM - DIESEL,
REPAIRS, Element - air cleaner.
3.Move injector harness clear of vacuum pump.
4.Release clip and disconnect hose from vacuum
pump.
5.Remove and discard 2 bolts securing vacuum
pump.
6.Remove vacuum pump and discard 'O' ring.Refit
1.Clean vacuum pump and mating face.
2.Fit new 'O' ring to vacuum pump.
3.Rotate vacuum pump drive to align with
camshaft, fit vacuum pump and tighten new
bolts to 22 Nm (16 lbf.ft).
4.Connect hose to vacuum pump and secure with
clip.
5.Reposition injector harness.
6.Fit air cleaner element.

+ FUEL DELIVERY SYSTEM - DIESEL,
REPAIRS, Element - air cleaner.
7.Connect battery earth lead.
M70 1031

BRAKES
REPAIRS 70-21
Vacuum pump - Td4 - automatic
$% 70.50.19
Remove
1.Disconnect battery earth lead.
2.Remove camshaft cover.

+ ENGINE - Td4, REPAIRS, Gasket -
camshaft cover.
3.Mark EGR pipe and cooler to aid refit.
4.Loosen clamps EGR pipes to cooler and move
clamps aside.
5.Remove pipe, EGR cooler to EGR valve.
6.Remove bolt securing fuel rails to support
bracket.
7.Remove bolt securing intercooler pipe to
support bracket.
8.Remove underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.9.Remove bolt securing turbo outlet pipe to upper
coolant rail.
10.Remove 2 bolts securing pipe support bracket
to engine lifting bracket, remove support
bracket.
11.Release clip and remove vacuum hose.
12.Remove and discard 2 bolts securing vacuum
pump.

M17 0283

BRAKES
70-22 REPAIRS
13.Remove 3 bolts securing EGR cooler to
cylinder head and lifting bracket.
14.Move EGR cooler aside for access to vacuum
pump.
15.Remove vacuum pump and discard 'O' ring.
Refit
1.Clean vacuum pump and mating face.
2.Fit new seal to vacuum pump, fit vacuum pump
and tighten new bolts to 22 Nm (16 lbf.ft).
3.Position EGR cooler to mounting, fit bolts and
tighten to 25 Nm (18 lbf.ft).
4.Position pipe support bracket to engine lifting
bracket, fit and tighten bolts to 25 Nm (18 lbf.ft).
5.Fit vacuum hose and tighten clip.
6.Fit bolt securing turbocharger pipe to coolant
rail and tighten to 25 Nm (18 lbf.ft).
7.Fit underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
8.Fit bolt securing turbocharger intercooler pipe
to support bracket and tighten to 10 Nm (7.5
lbf.ft).
9.Fit bolt securing fuel rails to support bracket
and tighten to 10 Nm (7.5 lbf.ft).
10.Align EGR pipe to cooler, fit clamp but do not
fully tighten until camshaft cover is refitted.
11.Fit EGR pipe clamp and tighten screw.
12.Fit camshaft cover.

+ ENGINE - Td4, REPAIRS, Gasket -
camshaft cover.
13.Connect battery earth lead.
Vacuum - enhancer - KV6
$% 70.50.20
Remove
1.Disconnect battery earth lead.
2.Remove engine accoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
3.Release enhancer from support clips.
4.Disconnect multiplug from solenoid valve if
fitted.
5.Release and disconnect servo pipe.
6.Release clip and disconnect from intake hose.
7.Release and remove enhancer assembly from
inlet manifold.
Refit
1.Fit enhancer to inlet manifold.
2.Connect to intake hose and secure with clip.
3.Connect servo hose.
4.Connect multiplug to solenoid valve if fitted.
5.Fit enhancer into clips.
6.Fit engine acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
7.Connect battery earth lead.