Camshaft LAND ROVER FREELANDER 2001 Repair Manual

ENGINE - K SERIES KV6
12-3-76 REPAIRS
7.Fit LRT-12-198 alignment pins into the end of
each camshaft.
8.Position timing belt and gears over LRT-12-198
and locate gears onto camshafts.
9.Position LRT-12-197 into the front end of the
RH exhaust camshaft.
10.With assistance, using a 30 mm socket on LRT-
12-197, turn the RH exhaust camshaft
sufficiently to align camshaft gears to the drive
slots in each camshaft.11.Remove LRT-12-198 alignment pins and fit
new camshaft gear retaining bolts.
12.Tighten camshaft gear bolts to:
lStage 1 - 27 Nm (20 lbf.ft)
lStage 2 - Further 90°
13.Remove LRT-12-175 from camshaft gears.
14.Remove LRT-12-197 from front end of exhaust
camshaft.
15.Clean RH exhaust camshaft cap seal recess
and fit new cap seal.
16.Remove timing pin LRT-12-232 from lower
crankcase.
17.Fit splash shield and secure with bolts.
18.Fit RH road wheel and tighten nuts to 115 Nm
(85 lbf.ft).
19.Fit RH rear timing belt cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Camshaft timing belt cover - RH rear.
20.Fit underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
21.Connect battery earth lead.

ENGINE - K SERIES KV6
12-3-80 OVERHAUL
Crankshaft front oil seal
$% 12.21.14.01
Remove
1.Remove camshaft timing belt.

+ ENGINE - K SERIES KV6,
OVERHAUL, Camshaft timing belt.
2.Remove crankshaft drive gear.
3.Fit thrust button, LRT-12-200/3 to end of
crankshaft.
4.Screw LRT-12-200 into crankshaft front oil
seal.
5.Tighten centre bolt of LRT-12-200 to remove oil
seal.
6.Remove and discard oil seal from LRT-12-200.
7.Remove thrust button from crankshaft.Refit
1.Clean oil seal recess in oil pump and running
surface on crankshaft, ensure bolt holes are
clean and dry.
2.Fit oil seal guide from seal kit, over end of
crankshaft.
3.Position new seal on crankshaft up against oil
pump housing. Drift seal into place using tool
LRT-12-202.
CAUTION: Oil seal must be fitted dry.
4.Remove LRT-12-202 and oil seal guide from
crankshaft.
5.Clean crankshaft gear and wipe end of
crankshaft.
6.Fit drive gear to crankshaft.
7.Fit camshaft timing belt.

+ ENGINE - K SERIES KV6,
OVERHAUL, Camshaft timing belt.

ENGINE - K SERIES KV6
OVERHAUL 12-3-87
Refit
1.Fit oil pump gasket.

+ ENGINE - K SERIES KV6,
OVERHAUL, Oil pump - Overhaul.
2.Fit engine sump.

+ ENGINE - K SERIES KV6,
OVERHAUL, Sump - engine oil.
3.Fit crankshaft rear oil seal.

+ ENGINE - K SERIES KV6,
OVERHAUL, Crankshaft rear oil seal.
4.Rotate crankshaft until timing pin LRT-12-232
can be inserted through hole immediately
adjacent to side of lower crankcase and into
elongated hole in drive plate.
CAUTION: Ensure that pin is in elongated
hole. Do not use cast arrow on oil pump
body as a timing mark. Do not remove
timing pin until timing belts are fitted.
5.Fit cylinder head gaskets.

+ ENGINE - K SERIES KV6,
OVERHAUL, Cylinder head gasket - LH.

+ ENGINE - K SERIES KV6,
OVERHAUL, Cylinder head gasket - RH.
Cylinder head gasket - LH
$% 12.29.02.01
Remove
1.Remove and discard camshaft timing belt.

+ ENGINE - K SERIES KV6,
OVERHAUL, Camshaft timing belt.
2.Remove inlet manifold chamber.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, OVERHAUL, Seals -
manifold chamber - up to 03MY.
3.Remove 4 bolts securing LH front camshaft
timing belt cover backplate to cylinder head and
remove backplate.
4.Release HO2S lead from clip on cylinder block.
5.Using sequence shown, loosen then remove 4
nuts securing exhaust manifold to cylinder
head. Remove manifold, remove and discard
gasket.
6.Remove LH camshaft cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Camshaft cover gasket - LH - Up to 03MY.
LRT-12-232
M12 7927

ENGINE - K SERIES KV6
12-3-90 OVERHAUL
10.Tighten cylinder head bolts progressively in the
sequence shown to:
lStage 1 - 25 Nm (18 lbf.ft)
lStage 2 - 25 Nm (18 lbf.ft)
lStage 3 - 25 Nm (18 lbf.ft)
lStage 4 - Using an angle torque gauge,
tighten a bolts in same sequence a further
180°
11.Fit LH camshaft cover gasket.

+ ENGINE - K SERIES KV6, REPAIRS,
Camshaft cover gasket - LH - Up to 03MY.
12.Remove and discard 'O' rings from injectors.
13.Clean injectors and injector locations in fuel rail.
14.Lubricate new 'O' rings with castor oil and fit to
injectors.
15.Position fuel rail assembly and secure injectors
to inlet manifolds.
16.Position injector protection cover - if fitted to RH
fuel rail and secure injector harness to
protection cover or fuel rail with clips.
17.Fit bolts securing fuel rail to inlet manifolds and
tighten to 9 Nm (7 lbf.ft).
18.Connect coolant bleed hose to inlet manifold
and secure with clip.
19.Connect breather hose to LH inlet manifold.
20.Position ignition coils to LH inlet manifold.
21.Position earth lead, fit nuts and bolts securing
ignition coils to LH inlet manifold and tighten to
9 Nm (7 lbf.ft).
22.Clean camshaft drive belt cover backplate bolts
and apply sealant, Part No. STC 50552 to first
3 threads.
23.Position backplate, fit and tighten bolts to 9 Nm
(7 lbf.ft).
24.Clean exhaust manifold and cylinder head
mating face.25.Fit new exhaust manifold gasket. Position
exhaust manifold, fit nuts and using sequence
shown, tighten to 45 Nm (33 lbf.ft).
26.Secure HO2S lead in clip on cylinder block.
27.Connect HO2S multiplug and secure to support
bracket.
28.Fit new camshaft timing belt.

+ ENGINE - K SERIES KV6,
OVERHAUL, Camshaft timing belt.

ENGINE - K SERIES KV6
OVERHAUL 12-3-91
Cylinder head gasket - RH
$% 12.29.03.01
Remove
1.Remove inlet manifold chamber.

+ MANIFOLDS & EXHAUST SYSTEMS
- K SERIES KV6, OVERHAUL, Seals -
manifold chamber - up to 03MY.
2.Remove and discard camshaft timing belt.

+ ENGINE - K SERIES KV6,
OVERHAUL, Camshaft timing belt.
3.Release RH HO2S multiplug from coolant rail
bracket and disconnect multiplug.
4.Using sequence shown, loosen then remove 4
nuts securing RH exhaust manifold to cylinder
head.
5.Remove exhaust manifold, remove and discard
gasket.6.Remove 4 bolts securing RH front timing belt
cover backplate to cylinder head and remove
backplate.
7.Remove RH camshaft cover gasket.

+ ENGINE - K SERIES KV6, REPAIRS,
Camshaft cover gasket - RH.
8. Up to 03MY: Remove 3 nuts and 3 bolts
securing ignition coils to LH inlet manifold and
release coil earth lead.
9. Up to 03MY:Remove ignition coils and position
aside.
M30 0996

ENGINE - K SERIES KV6
OVERHAUL 12-3-93
18.Fit cylinder liner clamps LRT-12-144 and
secure with cylinder head bolts.
CAUTION: Ensure that feet of clamps do not
protrude over bores.
Refit
1.Clean cylinder head face.
CAUTION: Use suitable gasket removal
spray and a plastic scraper.
2.Remove bolts securing cylinder liner clamps
LRT-12-144 to cylinder block and remove
clamps.
CAUTION: Do not rotate crankshaft.
3.Clean cylinder block face, dowels and dowel
holes.
4.Clean cylinder head bolts and wipe dry.
5.Lightly lubricate threads and beneath heads of
cylinder head bolts with clean engine oil.6.Check that fitted height of dowels is between 10
to 11 mm (0.40 to 0.43 in) above cylinder block
top face. Replace dowels if fitted height is
incorrect.
7.Fit new cylinder head gasket onto cylinder
block with the word 'TOP' uppermost.
8.With assistance, fit cylinder head and carefully
position RH inlet to LH inlet manifold.
9.Carefully enter cylinder head bolts, DO NOT
DROP. Screw bolts into place by hand.
10.Using sequence shown, tighten cylinder head
bolts progressively to:
lStage 1 - 25 Nm (18 lbf.ft)
lStage 2 - 25 Nm (18 lbf.ft)
lStage 3 - 25 Nm (18 lbf.ft)
lStage 4 - Further 180°
11.Fit RH camshaft cover gasket.

+ ENGINE - K SERIES KV6, REPAIRS,
Camshaft cover gasket - RH.
12.Remove and discard lower 'O' rings from
injectors.
13.Clean injectors and injector locations in fuel rail.
14.Lubricate new 'O' rings with castor oil and fit to
injectors.
15.Position fuel rail assembly and secure injectors
to inlet manifolds.

ENGINE - K SERIES KV6
12-3-94 OVERHAUL
16.Position injector protection cover - if fitted to RH
fuel rail and secure injector harness to
protection cover or fuel rail with clips.
17.Fit bolts securing fuel rail to inlet manifolds and
tighten to 9 Nm (7 lbf.ft).
18.Connect coolant bleed hose to inlet manifold
and secure with clip.
19. Up to 03MY:Position ignition coils to LH inlet
manifold.
20. Up to 03MY:Position earth lead, fit nuts and
bolts securing ignition coils to LH inlet manifold
and tighten to 9 Nm (7 lbf.ft).
21.Clean camshaft timing belt cover backplate
bolts and apply sealant, Part No. STC 50552 to
the first 3 threads.
22.Position backplate, fit and tighten bolts to 9 Nm
(7 lbf.ft).
23.Fit new camshaft timing belt.

+ ENGINE - K SERIES KV6,
OVERHAUL, Camshaft timing belt.
24.Clean exhaust manifold and mating face on
cylinder head.
25.Fit new exhaust manifold gasket. Position
exhaust manifold, fit nuts and using sequence
shown, tighten to 45 Nm (33 lbf.ft).
26.Connect RH HO2S multiplug, secure multiplug
in coolant rail bracket.
Cylinder head - decarbonise
$% 12.29.19
Remove
1.Remove cylinder head gaskets.

+ ENGINE - K SERIES KV6,
OVERHAUL, Cylinder head gasket - LH.

+ ENGINE - K SERIES KV6,
OVERHAUL, Cylinder head gasket - RH.
Disassembly
1. LH Cylinder head: Remove 3 bolts securing
LH rear timing belt cover and remove cover.
2. RH Cylinder head: Remove 2 bolts securing
RH rear timing belt cover heat shield to cylinder
head.
3. RH Cylinder head:Remove 3 bolts securing
RH rear timing belt cover; remove cover.
M12 6880
M12 6694

ENGINE - K SERIES KV6
OVERHAUL 12-3-95
4.Position LRT-12-175 to rear camshaft gears as
illustrated, remove and discard bolts securing
gears to camshafts.
5.Remove rear camshaft gears, timing belt and
LRT-12-175 as an assembly.
6.Remove LRT-12-175 from camshaft gears and
remove timing belt from gears. Discard timing
belt.
7.Remove spark plugs.
8.Remove and discard exhaust camshaft cap
seal from cylinder head.
Note: RH cylinder head illustrated.9.Progressively loosen then remove 7 bolts
securing inlet manifold to cylinder head,
remove inlet manifold and discard gasket.
10.Remove 4 bolts securing camshaft front timing
belt cover backplate to cylinder head and
remove backplate.
Note: LH backplate illustrated.
11.Remove 2 bolts securing camshaft rear timing
belt cover backplate to cylinder head and
remove backplate.
Note: LH backplate illustrated.
M12 6882
M12 6883

ENGINE - K SERIES KV6
12-3-96 OVERHAUL
12.Check end-float of camshafts using a DTI.

+ GENERAL DATA, Engine - KV6
Petrol.
CAUTION: If camshaft end-float exceeds
limits given, repeat check with new
camshaft(s). If end-float is still excessive,
replace cylinder head and camshaft carrier
as an assembly.
13.Using sequence shown, progressively loosen
22 bolts securing camshaft carrier to cylinder
head until valve spring pressure is released
and remove bolts.
14.Remove camshaft carrier.15.Remove camshafts and discard oil seals.
Note: Inlet camshafts are colour coded orange,
exhaust camshafts
16.Using a stick magnet, remove 12 hydraulic
tappets from cylinder head.
CAUTION: Store hydraulic tappets in their
fitted order and store upright. Maintain
absolute cleanliness when handling
hydraulic tappets. Failure to observe these
precautions can result in engine failure.
17.Measure the outside diameter of hydraulic
tappets.

+ GENERAL DATA, Engine - KV6
Petrol.
Note: Measurement must be taken half-way
along tappet body.
18.Using LRT-12-034, and adapter LRT-12-034/1,
compress valve spring, remove 2 collets,
release valve spring and remove LRT-12-034.
19.Remove valve spring cap and valve spring.
20.Remove valve from cylinder head.

ENGINE - K SERIES KV6
OVERHAUL 12-3-97
21.Remove valve stem oil seal using LRT-12-071.
Discard stem seal.
22.Repeat procedure for remaining valves,
keeping components in their fitted order.
Inspect
1.Clean camshafts, bearing running surfaces in
carrier and cylinder head, carrier and cylinder
head mating faces.
2.Inspect camshafts and replace camshafts if
scored, pitted or excessively worn.
3.Position camshafts in cylinder head and place
Plastigauge across each journal.
CAUTION: Ensure camshafts are in their
correct fitted locations. Camshafts are
colour coded - Inlet - Orange; Exhaust -
Blue.
4.Refit camshaft carrier, fit bolts and using
sequence shown, tighten to 10 Nm (7.5 lbf.ft).
Do not rotate camshafts.5.Using the sequence shown, progressively
loosen and remove camshaft carrier bolts.
Release and remove camshaft carrier from
cylinder head.
6.Measure widest part of Plastigauge on each
journal.

+ GENERAL DATA, Engine - KV6
Petrol.
7.If clearance is excessive, fit new camshafts and
repeat check. If clearance is still excessive
renew cylinder head.
8.Remove all traces of Plastigauge using an oily
rag.
9.Clean sealing surfaces of cylinder heads.
Clean inlet and exhaust manifold mating faces.
CAUTION: Do not use a metal scraper.
10.Decarbonise combustion areas of cylinder
heads
11.Blow out all oilways and coolant passages.
12.Check cylinder head for damage, pay particular
attention to sealing faces.
M12 6889
LRT-12-071
mm.025.038.051.076
M12 6887