alternator belt LAND ROVER FREELANDER 2001 User Guide

MANIFOLDS & EXHAUST SYSTEMS - K SERIES KV6
30-3-12 REPAIRS
Gasket(s) - exhaust manifold - LH - NAS
$% 30.15.17
Remove
1.Position vehicle on 4 post ramp.
2.Disconnect battery earth lead.
3.Remove engine acoustic cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Cover - engine acoustic.
4.Remove underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
5.Using a 3/8" socket bar raise ancillary drive belt
tensioner and release drive belt from alternator
and PAS pump pulleys.
6.Remove 3 bolts securing A/C compressor to
fixing brackets and position compressor aside.
7.Remove compressor heat shield.8.Release and disconnect HO2S multiplug.
9.Release HO2S harness from clip.
10.Release and disconnect post catalyst HO2S
multiplug.
11.Release HO2S harness from clips.
12.Remove 2 nuts securing exhaust front pipe to
exhaust manifold.
M30 1142
M19 3505
M19 3481

STEERING
57-12 REPAIRS
Pump - steering - KV6
$% 57.20.14
Remove
1.Disconnect battery earth lead.
2.Remove engine mounting top arm.

+ ENGINE - K SERIES KV6, REPAIRS,
Arm assembly - engine mounting RH.
3.Loosen PAS pump pulley bolts.
4.Using a 3/8" socket bar, raise ancillary drive
belt tensioner and release drive belt from
alternator and PAS pump pulleys.
5.Position container to collect PAS fluid spillage.6.Release clip and disconnect fluid inlet hose
from PAS pump.
7.Remove banjo bolt securing fluid outlet hose to
PAS pump, release hose, remove and discard
sealing washers.
CAUTION: To prevent damage to
components, use two spanners when
loosening or tightening unions.
8.Remove bolt securing PAS outlet pipe support
bracket to cylinder head and move pipe aside.
9.Remove 3 bolts securing PAS pump pulley to
PAS pump and remove pulley.
CAUTION: Always fit plugs to open
connections to prevent contamination.

STEERING
REPAIRS 57-15
Pump - steering - Td4
$% 57.20.14
Remove
1.Disconnect battery earth lead.
2.Remove hydramount.

+ ENGINE - Td4, REPAIRS,
Hydramount - engine - RH.
3.Loosen 3 PAS pump pulley bolts.
4.Remove ancillary drive belt.

+ CHARGING AND STARTING,
REPAIRS, Ancillary drive belt - Td4.
5.Raise engine on hoist.
6.Remove bolts and remove PAS pump pulley.
7.Cover alternator to prevent PAS oil
contamination.
8.Place container beneath PAS pump, release
clip and remove feed hose to pump. Allow fluid
to drain.
CAUTION: Care must be taken to ensure
that oil or fluid does not enter or
contaminate the alternator.9.Remove banjo bolt securing fluid outlet hose to
PAS pump, release hose, remove and discard
sealing washers.
CAUTION: Before disconnecting or
removing components, ensure the
immediate area around joint faces and
connections are clean. Plug open
connections to prevent contamination.
10.Remove 4 bolts and remove PAS pump.
11.Remove 5 Torx bolts securing PAS pump to
mounting brackets. Collect mounting brackets.
Refit
1.Position PAS pump to mounting brackets, fit
and tighten Torx bolts to 25 Nm (18 lbf.ft).
2.Position pump to mounting, fit bolts and tighten
M8 bolts to 25 Nm (18 lbf.ft) and M6 bolts to 10
Nm (7.5 lbf.ft).
3.Using new sealing washers, fit PAS outlet hose
to pump and tighten banjo bolt to 25 Nm (18
lbf.ft).
4.Clean PAS pump and mating faces.
5.Fit inlet hose to PAS pump and secure with new
clip.
6.Fit PAS pump pulley to PAS pump and tighten
bolts to finger tight.
7.Fit ancillary drive belt.

+ CHARGING AND STARTING,
REPAIRS, Ancillary drive belt - Td4.
8.Tighten PAS pump pulley bolts to 10 Nm (7.5
lbf.ft).
9.Fit hydramount.

+ ENGINE - Td4, REPAIRS,
Hydramount - engine - RH.
10.Connect battery earth lead.

PANEL REPAIRS
REPAIRS 77-2-45
'B/C' post reinforcement - 3 door
In this procedure, the rear outer body side panel and
the rear quarter front lower reinforcement are
replaced in conjunction with the 'B/C' post
reinforcement.
Remove
1.Disconnect battery earth lead.
2.Disconnect alternator.
3.Disconnect all ECUs.
4.Remove road wheel(s).
5.Remove rear wheel arch extension.

+ EXTERIOR FITTINGS, REPAIRS,
Wheelarch extension - rear wing part.
6.Remove rear wheel arch liner.
7.Remove front seat belt.

+ RESTRAINT SYSTEMS, REPAIRS,
Automatic belt assembly - front - 3 door.
8.Remove front door striker from 'B/C' post.
9.Remove rear seat.

+ SEATS, REPAIRS, Rear seat - LH.

+ SEATS, REPAIRS, Rear seat - RH.
10.Remove rear body side casing.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - body side - rear - 3
door.
11.Remove treadplate from side door aperture.
12.Remove side door aperture seal.
13.Release carpet from inner sill and position
aside.
14.Remove rear quarter vent and seal.

+ EXTERIOR FITTINGS, REPAIRS,
Body quarter vent assembly - 3 door.
15.Remove rear roof panel finisher.
16.Remove headlining.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Headlining - 3 door.
17.Release vehicle harness from inner sill and
position aside. Repair
1.Remove existing panel(s), prepare panel joint
faces and install new panel(s) in accordance
with Panel Replacement Procedure. Punch or
drill holes in new panel for plug welding as
shown.

PANEL REPAIRS
77-2-46 REPAIRS
Refit
1.Secure vehicle harness to inner sill.
2.Fit headlining.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Headlining - 3 door.
3.Fit rear roof panel finisher.
4.Fit seal and rear quarter vent.

+ EXTERIOR FITTINGS, REPAIRS,
Body quarter vent assembly - 3 door.
5.Secure carpet to inner sill.
6.Fit side door aperture seal.
7.Fit treadplate from side door aperture.
8.Fit rear body side casing.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - body side - rear - 3
door.
9.Fit rear seat.

+ SEATS, REPAIRS, Rear seat - LH.

+ SEATS, REPAIRS, Rear seat - RH.
10.Fit front door striker to 'B/C' post.
11.Fit front seat belt.

+ RESTRAINT SYSTEMS, REPAIRS,
Automatic belt assembly - front - 3 door.
12.Fit rear wheel arch liner.
13.Fit rear wheel arch extension.

+ EXTERIOR FITTINGS, REPAIRS,
Wheelarch extension - rear wing part.
14.Fit road wheel(s) and tighten nuts to 115 Nm
(85 lbf.ft).
15.Connect all ECUs.
16.Connect alternator.
17.Connect battery earth lead.
'B/C' post reinforcement - 5 door
In this procedure, the rear outer body side panel and
the inner panel are replaced in conjunction with the
'B/C' post reinforcement.
Remove
1.Disconnect battery earth lead.
2.Disconnect alternator.
3.Disconnect all ECUs.
4.Remove rear door.

+ DOORS, REPAIRS, Door assembly
- rear - remove for access & refit.
5.Remove headlining.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Headlining - 5 door.
6.Remove front seat belt.

+ RESTRAINT SYSTEMS, REPAIRS,
Automatic belt assembly - front - 5 door.
7.Remove 'B/C' post lower finisher.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim finisher - 'B' post - lower - 5
door.
8.Remove front door striker from 'B/C' post.
9.Remove front seat.

+ SEATS, REPAIRS, Front seat.
10.Remove rear seat.

+ SEATS, REPAIRS, Rear seat - LH.

+ SEATS, REPAIRS, Rear seat - RH.
11.Remove treadplate from side door aperture(s).
12.Remove side door aperture seal(s).
13.Release carpet from inner sill and position
aside.
14.Release vehicle harness from inner sill and
position aside.

PANEL REPAIRS
77-2-48 REPAIRS
Refit
1.Secure vehicle harness to inner sill.
2.Position carpet to inner sill.
3.Fit side door aperture seal(s).
4.Fit treadplate from side door aperture(s).
5.Fit rear seat.

+ SEATS, REPAIRS, Rear seat - LH.
6.Fit front seat.

+ SEATS, REPAIRS, Front seat.
7.Fit front door striker to 'B/C' post.
8.Fit 'B/C' post lower finisher.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim finisher - 'B' post - lower - 5
door.
9.Fit front seat belt.

+ RESTRAINT SYSTEMS, REPAIRS,
Automatic belt assembly - front - 5 door.
10.Fit headlining.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Headlining - 5 door.
11.Fit rear door.

+ DOORS, REPAIRS, Door assembly
- rear - remove for access & refit.

+ SEATS, REPAIRS, Rear seat - RH.
12.Connect all ECUs.
13.Connect alternator.
14.Connect battery earth lead.
Complete rear quarter - 3 door
In this procedure, the rear outer body side panel is
replaced in conjunction with the complete rear
quarter.
Remove
1.Disconnect battery earth lead.
2.Disconnect alternator.
3.Disconnect all ECUs.
4.Remove road wheel(s).
5.Remove sill lower finisher.

+ EXTERIOR FITTINGS, REPAIRS,
Finisher - sill - lower.
6.Remove rear bumper valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper valance - rear - up to 04MY.
7.Remove rear wheel arch liner.
8.Remove door striker from 'B' post.
9.Remove treadplate from front door aperture.
10.Remove front door aperture seal.
11.Release carpet from inner sill and rear
heelboard and position aside.
12.Remove soft/hard top.
13.Remove tail door aperture seal.
14.Remove rear roof panel finisher.

+ EXTERIOR FITTINGS, REPAIRS,
Moulding - roof - 5 door.
15.Remove tail lamp.

+ LIGHTING, REPAIRS, Lamp
assembly - tail.
16.Remove rear quarter lower casing.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - rear quarter - lower
- 3 door.
17.Remove rear quarter upper casing.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - rear quarter - upper
- 3 door.
18.Remove rear side seat belt.

+ RESTRAINT SYSTEMS, REPAIRS,
Seat belt - rear - LH.
19.Remove loadspace carpet.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Carpet - luggage compartment.
20.Remove rear seat.

+ SEATS, REPAIRS, Rear seat - LH.

+ SEATS, REPAIRS, Rear seat - RH.
21.Remove rear body side casing.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - body side - rear - 3
door.
22.Remove headlining.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Headlining - 3 door.

PANEL REPAIRS
77-2-50 REPAIRS
10.Fit rear seat.

+ SEATS, REPAIRS, Rear seat - LH.

+ SEATS, REPAIRS, Rear seat - RH.
11.Fit loadspace carpet.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Carpet - luggage compartment.
12.Fit rear side seat belt.

+ RESTRAINT SYSTEMS, REPAIRS,
Seat belt - rear - LH.
13.Fit rear quarter upper casing.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - rear quarter - upper
- 3 door.
14.Fit rear quarter lower casing.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - rear quarter - lower
- 3 door.
15.Fit tail lamp.

+ LIGHTING, REPAIRS, Lamp
assembly - tail.
16.Fit rear roof panel finisher.

+ EXTERIOR FITTINGS, REPAIRS,
Moulding - roof - 5 door.
17.Fit tail door aperture seal.
18.Fit soft/hard top.
19.Secure carpet to inner sill and rear heelboard.
20.Fit front door aperture seal.
21.Fit treadplate to front door aperture.
22.Fit door striker to 'B' post.
23.Fit rear wheel arch liner.
24.Fit rear bumper valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper valance - rear - up to 04MY.
25.Fit sill lower finisher.

+ EXTERIOR FITTINGS, REPAIRS,
Finisher - sill - lower.
26.Fit road wheel(s) and tighten nuts to 115 Nm
(85 lbf.ft).
27.Connect all ECUs.
28.Connect alternator.
29.Connect battery earth lead.
Complete rear quarter - 5 door
In this procedure, the rear outer body side panel is
replaced in conjunction with the complete rear
quarter.
Remove
1.Disconnect battery earth lead.
2.Disconnect alternator.
3.Disconnect all ECUs.
4.Remove road wheel(s).
5.Remove sill lower finisher.

+ EXTERIOR FITTINGS, REPAIRS,
Finisher - sill - lower.
6.Remove rear bumper valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper valance - rear - up to 04MY.
7.Remove rear wheel arch liner.
8.Remove rear door striker from 'D' post.
9.Remove treadplate from rear door aperture.
10.Remove rear door aperture seal.
11.Release carpet from inner sill and rear
heelboard and position aside.
12.Remove tail door glass upper finisher.
13.Remove tail door glass side finisher.

+ DOORS, REPAIRS, Finisher - rear
screen - side - 5 door.
14.Remove tail door aperture seal.
15.Remove roof panel finisher.

+ EXTERIOR FITTINGS, REPAIRS,
Moulding - roof - 5 door.
16.Remove tail lamp.

+ LIGHTING, REPAIRS, Lamp
assembly - tail.
17.Remove rear quarter lower casing.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - rear quarter - lower
- 5 door.
18.Remove rear quarter upper casing.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - rear quarter - upper
- 5 door.
19.Remove rear side seat belt.

+ RESTRAINT SYSTEMS, REPAIRS,
Seat belt - rear - LH.
20.Remove loadspace carpet.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Carpet - luggage compartment.
21.Remove rear seat.

+ SEATS, REPAIRS, Rear seat - LH.

+ SEATS, REPAIRS, Rear seat - RH.
22.Remove headlining.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Headlining - 5 door.

PANEL REPAIRS
77-2-52 REPAIRS
1.Remove existing panel(s), prepare panel joint
faces and install new panel(s) in accordance
with Panel Replacement Procedure. Punch or
drill holes in new panel for plug welding as
shown.
2.Arrow A is shown to highlight the fact that there
are plug welds on the other side of the inner
wheel arch as well. These are to weld the rear
longitudinal to the inner wheel arch.
Refit
1. LH side: Fit tail door striker to 'E' post.
2. RH side: Fit fuel tank.

+ FUEL DELIVERY SYSTEM -
PETROL, REPAIRS, Tank - Non NAS.
3. RH side: Fit fuel filler neck.

+ FUEL DELIVERY SYSTEM -
PETROL, REPAIRS, Filler neck.
4. RH side: Fit tail door.

+ DOORS, REPAIRS, Door - tail
assembly - remove for access & refit.
5.Secure vehicle harness to rear quarter.
6.Fit rear damper.

+ REAR SUSPENSION, REPAIRS,
Damper.
7.Fit rear body side glass.

+ SCREENS, REPAIRS, Glass - body
side - rear.
8.Fit headlining.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Headlining - 5 door.9.Fit rear seat.

+ SEATS, REPAIRS, Rear seat - LH.

+ SEATS, REPAIRS, Rear seat - RH.
10.Fit loadspace carpet.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Carpet - luggage compartment.
11.Fit rear side seat belt.

+ RESTRAINT SYSTEMS, REPAIRS,
Seat belt - rear - LH.
12.Fit rear quarter upper casing.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - rear quarter - upper
- 5 door.
13.Fit rear quarter lower casing.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim casing - rear quarter - lower
- 5 door.
14.Fit tail lamp.

+ LIGHTING, REPAIRS, Lamp
assembly - tail.
15.Fit roof panel finisher.

+ EXTERIOR FITTINGS, REPAIRS,
Moulding - roof - 5 door.
16.Fit tail door aperture seal.
17.Fit tail door glass side finisher.

+ DOORS, REPAIRS, Finisher - rear
screen - side - 5 door.
18.Fit tail door glass upper finisher.
19.Secure carpet to inner sill and rear heelboard.
20.Fit rear door aperture seal.
21.Fit treadplate to rear door aperture.
22.Fit rear door striker to 'D' post.
23.Fit rear wheel arch liner.
24.Fit rear bumper valance.

+ EXTERIOR FITTINGS, REPAIRS,
Bumper valance - rear - up to 04MY.
25.Fit sill lower finisher.

+ EXTERIOR FITTINGS, REPAIRS,
Finisher - sill - lower.
26.Fit road wheel(s) and tighten nuts to 115 Nm
(85 lbf.ft).
27.Connect all ECUs.
28.Connect alternator.
29.Connect battery earth lead.

AIR CONDITIONING
82-8REPAIRS
Refit
1.If a new compressor is being installed, drain the
required amount of refrigerant oil from the new
compressor.

+ GENERAL INFORMATION, Air
conditioning compressor replacement.
2.A new compressor is sealed and pressurised
with Nitrogen gas, slowly release the sealing
cap, gas pressure should be heard to release
as the seal is broken.
3.Clean compressor and mating face on front
mounting plate and cylinder block.
4.Position compressor, fit but do not fully tighten
lower bolt.
5.Position heat shield and fit compressor upper
securing bolts. Tighten compressor upper and
lower securing bolts to 25 Nm (18 lbf.ft).
6.Remove caps from compressor and high
pressure pipe.
7.Clean compressor high pressure pipe
connection.
8.Lubricate new 'O' ring with refrigerant oil and fit
to high pressure pipe.
9.Connect high pressure pipe to compressor, fit
and tighten bolt to 25 Nm (18 lbf.ft).
10.Connect multiplug to compressor.
11.Remove caps from compressor and low
pressure pipe.
12.Clean compressor low pressure pipe
connection.
13.Lubricate new 'O' ring with refrigerant oil and fit
to low pressure pipe.
14.Connect low pressure pipe to compressor, fit
and tighten bolt to 25 Nm (18 lbf.ft).
15.Clean pulley 'V's and tensioner pulley running
surface.
16.Using a 3/8” square drive socket bar, raise
ancillary drive belt tensioner and fit drive belt to
pulleys.
17.Fit splash shield and secure with bolts.
18.Fit RH road wheel and tighten nuts to 115 Nm
85 lbf.ft).
19.Replace receiver drier.

+ AIR CONDITIONING, REPAIRS,
Receiver drier.
20.Recharge A/C system.

+ AIR CONDITIONING, REFRIGERANT
RECOVERY, RECYCLING AND
RECHARGING, Refrigerant recovery -
recycling and recharge.
21.Connect battery earth lead.
22.Fit underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
Compressor - K1.8
$% 82.10.20
Remove
1.Disconnect battery earth lead.
2.Raise front of vehicle.
WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.
3.Remove underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
4.Recover refrigerant from A/C system.

+ AIR CONDITIONING, REFRIGERANT
RECOVERY, RECYCLING AND
RECHARGING, Refrigerant recovery -
recycling and recharge.
5.Remove alternator.

+ CHARGING AND STARTING,
REPAIRS, Alternator - K1.8.
6.Disconnect multiplug from compressor.
7.Remove 2 bolts securing A/C pipes to
compressor, release A/C pipes from
compressor.
CAUTION: Before disconnecting or
removing components, ensure the
immediate area around joint faces and
connections are clean. Plug open
connections to prevent contamination.
8.Remove and discard 'O' rings from A/C pipes.

M82 0730

CHARGING AND STARTING
ADJUSTMENTS 86-1-1
CHARGING AND STARTING ADJUST ME NTS
Ancillary drive belt - K1.8
$% 86.10.05
Check
1.Disconnect battery earth lead.
2.Turn steering on RH lock.
3.Remove 3 bolts and remove splash shield.
4.Rotate crankshaft a sufficient number of turns
to check condition of drive belt. Renew a drive
belt that shows signs of wear, splitting or oil
contamination.
5.Apply a force of 10 kg to drive belt at position 'X'
and measure deflection between crankshaft
pulley and alternator pulley. Deflection must be
6 - 8 mm.Adjust
1.Loosen alternator pivot nut and bolt.
2.Loosen bolt securing alternator adjustment
bracket to engine.
3.Loosen bolt securing alternator to adjustment
bracket.
4.Increase drive belt tension by rotating
alternator adjustment bolt clockwise.
5.Tighten alternator pivot and adjustment bracket
bolts to 25 Nm (18 lbf.ft).
6.Recheck drive belt tension.
7.Fit splash shield and secure with bolts.
8.Straighten steering.
9.Connect battery earth lead.