Oil pump LAND ROVER FREELANDER 2001 Owner's Manual

ENGINE - K SERIES KV6
12-3-52 REPAIRS
Refit
1.Clean oil pump and mating face on cylinder
block ensure bolt holes are clean and dry.
2.Clean oil seal recess in oil pump and running
surface on crankshaft.
3.Fit new oil pump gasket, dry, to cylinder block.
4.Fit oil seal guide, from seal kit, over end of
crankshaft.
5.Position oil pump, aligning flats on oil pump
drive to flats on crankshaft. Fit new Patchlok
bolts and tighten progressively in sequence
shown to:
lStage 1 - 5 Nm (4 lbf.ft)
lStage 2 - 9 Nm (7 lbf.ft)
6.Position new seal on crankshaft up against oil
pump housing. Drift seal into place using tool
LRT-12-202.
CAUTION: Oil seal must be fitted dry.
7.Remove oil seal guide from crankshaft.
8.Connect multiplug to oil pressure switch.
9.Fill canister of replacement oil filter with clean
engine oil.10.Lubricate oil filter sealing ring with clean engine
oil.
11.Fit oil filter and tighten by hand until it seats
then tighten a further half turn.
12.Lubricate new 'O' rings with clean engine oil
and fit to oil cooler pipe unions.
13.Connect oil cooler pipes to oil filter housing and
tighten unions to 26 Nm (19 lbf.ft).
14.Clean crankshaft gear and wipe end of
crankshaft.
15.Fit crankshaft gear.
16.Fit camshaft timing belt.

+ ENGINE - K SERIES KV6, REPAIRS,
Camshaft timing belt.
17.Fill engine with oil.

+ MAINTENANCE, MAINTENANCE,
Engine Oil and Filter – KV6.
18.Connect battery earth lead.

ENGINE - K SERIES KV6
12-3-56 REPAIRS
7.Remove 4 nuts securing engine oil cooler to
mounting bracket and position oil cooler aside.
8.Remove oil pressure relief valve plug nut.
Note: If a hexagonal head plug and sealing
washer are fitted, discard sealing washer.
9.Remove spring and valve.Refit
1.Clean valve, spring and plug; remove all traces
of sealant from threads in oil pressure relief
valve bore and from threads of plug.
CAUTION: Do not use a tap.
2.Clean valve seating inside oil pump housing.
3.Check that valve slides freely in bore and that
valve and bore are free from scoring and
corrosion.
Note: Light corrosion may be removed using
grade 600 emery cloth soaked in oil.
4.Check free length of spring.

+ GENERAL DATA, Engine - KV6
Petrol.
5.Apply sealant, Part No. STC 50552 to plug
threads.
Note: If a hexagonal head plug and sealing
washer were fitted, fit new sealing washer to
plug.
6.Fit valve, spring and plug to oil pump housing.
Tighten plug to 25 Nm (18 lbf.ft).
7.Fill canister of replacement oil filter with clean
engine oil.
8.Lubricate new oil filter seal with clean engine oil
and fit filter.
9.Position engine oil cooler to mounting bracket,
fit and tighten nuts to 25 Nm (18 lbf.ft).
10.Remove oil container from underneath of
engine.
11.Fit splash shield and secure with bolts.
12.Fit RH road wheel and tighten nuts to 115 Nm
(85 lbf.ft).
13.Fit underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
14.Connect battery earth lead.
15.Check engine oil level, top-up if necessary.
M12 7916

ENGINE - K SERIES KV6
REPAIRS 12-3-63
38.Remove and discard 2 Patchlok bolts securing
tensioner to cylinder block and remove
tensioner.
CAUTION: Exercise great care when
removing bolts, do not apply excessive
torque. If bolts appear to be seized, apply
suitable anti-seize lubricant prior to
removing bolts. DO NOT loosen Allen screw
securing tensioner pulley.
39.If camshaft timing belt is to be refitted, mark
direction of rotation on timing belt before
removal.
40.With care, ease camshaft timing belt from
gears using fingers only and remove timing
belt.
CAUTION: Do not rotate crankshaft or
camshafts with timing belt removed and
cylinder heads fitted.
CAUTION: Camshaft timing belt must be
replaced if cylinder head is to be removed or
new drive gears, tensioner or coolant pump
are to be fitted. Camshaft timing belts must
be stored and handled with care. Always
store a camshaft timing belt on its edge with
a bend radius greater than 50 mm (2.0 in).
Do not use a camshaft timing belt that has
been twisted or bent double as this will
damage the reinforcing fibres. Do not use a
camshaft timing belt if debris other than belt
dust is found in timing belt covers. Do not
use a camshaft timing belt if partial engine
seizure has occurred. Do not use a
camshaft timing belt if mileage exceeds
72,000 km (45,000 miles). Do not use an oil
or coolant contaminated timing belt, cause
of contamination must be rectified.41.Remove and discard LH and RH exhaust
camshaft cap seals.
42.Position tools LRT-12-196 to LH and RH front
inlet camshaft gears and into the end of each
exhaust camshaft.
CAUTION: Special tools must be fitted when
tightening or loosening gear retaining bolts,
otherwise damage to camshafts may occur.
43.Remove and discard bolts retaining front inlet
camshaft gears to camshafts.
44.Remove tools LRT-12-196 from both inlet
camshaft gears and exhaust camshafts.
45.Remove camshaft drive gears and hub
assemblies.

ENGINE - K SERIES KV6
12-3-64 REPAIRS
Refit
NOTE: Following front or rear timing belt
refitment, it is possible that, after rotating the
engine and positioning the crankshaft pulley to
the 'SAFE' position, the timing marks on the
rear timing gears may be misaligned. This
misalignment is acceptable provided that the
timing belt refitting procedure was carried out
correctly.
1.Clean camshaft gears and hubs, crankshaft
gear, tensioner and water pump pulleys.
CAUTION: If the sintered gears have been
subjected to prolonged oil contamination,
they must be soaked in a solvent bath and
then thoroughly washed in clean solvent
before refitting. Because of the porous
construction of sintered material, oil
impregnated in the gears will emerge and
contaminate the belt.
2.Fit hubs to camshaft gears and fit gears to
camshafts. Fit new bolts and tighten sufficiently
to allow gears to rotate without tipping.
3.Position timing belt to crankshaft gear.
NOTE: To prevent the timing belt from
disengaging from the crankshaft gear when
fitting, fit a suitable wedge between the belt and
oil pump belt guard.
4.Fit tool LRT-12-197 into each exhaust
camshaft in turn.5.Using assistance, rotate each exhaust
camshaft slightly and align timing marks on LH
and RH rear camshaft gears.
6.Remove tool LRT-12-197 from exhaust
camshaft.
7.Fit tools LRT-12-175 to LH and RH rear
camshaft gears.
8.Rotate both front inlet camshaft gears fully
clockwise as viewed from front of engine.
9.Using fingers only, fit timing belt to gears,
starting at the crankshaft gear and working in
an anti-clockwise direction, keeping the belt run
as taut as possible and turning the camshaft
gears only a minimum amount anti-clockwise to
fit timing belt.
CAUTION: Gears must not be rotated anti-
clockwise more than one tooth.
10.Position an Allen key in tensioner backplate
and hold tensioner pulley against timing belt.

ENGINE - K SERIES KV6
REPAIRS 12-3-65
11.With assistance, position tensioner, fit new
Patchlok bolts and tighten to 25 Nm (18 lbf.ft).
CAUTION: Ensure tensioner plunger is
contacting underside of tensioner
backplate.
12.Remove tools LRT-12-175 from rear timing belt
gears.
13.Fit tools LRT-12-196 to both front inlet
camshaft gears and into the end of each
exhaust camshaft.
CAUTION: Special tools must be fitted when
tightening or loosening gear retaining bolts,
otherwise damage to camshafts may occur.
14. Tighten front inlet camshaft gear bolts to:
lStage 1 - 27 Nm (20 lbf.ft)
lStage 2 - Further 90°
15.Remove tools LRT-12-196 from both inlet
camshaft gears and exhaust camshafts.
16.Remove wedge from between drive belt and oil
pump belt guard.
17.Remove 1.5 mm diameter pin from tensioner.
18.Fit rubber blanking plug around tensioner.
19.Remove timing pin LRT-12-232.
20.Clean exhaust camshaft front cap seal
locations and fit new cap seals.
CAUTION: The sealing edge of the cap seal
and mating face must be clean and dry.
21.Position engine front mounting plate and
manoeuvre plate into position. Fit bolts but do
not tighten at this stage.22.Fit bolts securing IRD support bracket to front
mounting plate but do not tighten at this stage.
23.Tighten bolts in the sequence shown:
lBolt No. 1 - 25 Nm (18 lbf.ft)
lBolt No. 5 - 45 Nm (33 lbf.ft)
lBolts Nos. 2, 3, 4, 6 and 7 - 85 Nm (63 lbf.ft)
24.Position engine lifting bracket, fit bolts securing
lifting bracket and front mounting plate to
cylinder block and RH cylinder head. Tighten
M10 bolts to 45 Nm (33 lbf.ft) and M8 bolt to 25
Nm (18 lbf.ft).
25.Clean end of dipstick tube.
26.Position dipstick tube to sump and cylinder
block, fit bolt and tighten to 9 Nm (7 lbf.ft).
27.Position A/C compressor to front mounting
plate and cylinder block, align heat shield, fit
and tighten bolts to 25 Nm (18 lbf.ft).
28.Clean lower timing belt cover.
29.Position lower timing belt cover, fit and tighten
bolts to 9 Nm (7 lbf.ft).
30.Clean crankshaft pulley.
31.Fit crankshaft pulley to crankshaft gear and
ensure that the indent on pulley locates over
the lug on crankshaft gear.
32.Fit crankshaft pulley bolt and washer, position
LRT-12-161 with LRT-12-199 into crankshaft
pulley. Tighten pulley bolt to 160 Nm (118
lbf.ft).
33.Remove tools LRT-12-161 and LRT-12-
199from crankshaft pulley.
34.Clean ancillary drive belt tensioner.
35.Position ancillary belt tensioner, fit bolts and
tighten to 25 Nm (18 lbf.ft).
36.Clean LH and RH front timing belt covers.
37.Position LH and RH front timing belt covers, fit
and tighten bolts to 4 Nm (3 lbf.ft).
38.Clean idler pulley, position pulley to engine
front mounting plate and tighten Allen bolt to 45
Nm (33 lbf.ft).
39.Position alternator to front mounting plate.

ENGINE - K SERIES KV6
REPAIRS 12-3-69
Camshaft rear timing belt - LH cylinder
head
$% 12.65.56
Remove
1.Disconnect battery earth lead.
2.Remove underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
3.Remove LH rear timing belt cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Camshaft timing belt cover - LH rear.
4.Remove RH front road wheel.
5.Remove 3 bolts securing RH splash shield to
body and remove shield.6.Using a socket on crankshaft pulley bolt, rotate
crankshaft in a clockwise direction. Align the
engine "SAFE" position, notch on crankshaft
pulley aligned to the "ARROW" on front
mounting plate and the timing marks aligned on
the rear camshaft gears as illustrated.
CAUTION: Do not use camshaft gear bolts
or timing belt to rotate crankshaft. Never
use the arrow on the oil pump body as a
timing reference.
7.Insert timing pin LRT-12-232 through hole in
lower crankcase, ensuring pin is located in hole
in drive plate.
CAUTION: Hole immediately adjacent to
side of lower crankcase must be used.
M12 6614
LRT-12-232
M12 7927

ENGINE - K SERIES KV6
REPAIRS 12-3-73
Camshaft rear timing belt - RH cylinder
head
$% 12.65.57
Remove
1.Disconnect battery earth lead.
2.Remove underbelly panel.

+ EXTERIOR FITTINGS, REPAIRS,
Panel - underbelly.
3.Remove RH front road wheel.
4.Remove 3 bolts securing RH splash shield to
body and remove shield.
5.Remove RH rear timing belt cover.

+ ENGINE - K SERIES KV6, REPAIRS,
Camshaft timing belt cover - RH rear.6.Using a socket on crankshaft pulley bolt, rotate
crankshaft in a clockwise direction. Align the
engine "SAFE" position, notch on crankshaft
pulley aligned to the "ARROW" on front
mounting plate and the timing marks aligned on
the rear camshaft gears as illustrated.
CAUTION: Do not use camshaft gear bolts
or timing belt to rotate crankshaft. Never
use the arrow on the oil pump body as a
timing reference.
7.Insert timing pin LRT-12-232 through hole in
lower crankcase, ensuring pin is located in hole
in drive plate.
CAUTION: Hole immediately adjacent to
side of lower crankcase must be used.
M12 6614
LRT-12-232
M12 7927

ENGINE - K SERIES KV6
12-3-80 OVERHAUL
Crankshaft front oil seal
$% 12.21.14.01
Remove
1.Remove camshaft timing belt.

+ ENGINE - K SERIES KV6,
OVERHAUL, Camshaft timing belt.
2.Remove crankshaft drive gear.
3.Fit thrust button, LRT-12-200/3 to end of
crankshaft.
4.Screw LRT-12-200 into crankshaft front oil
seal.
5.Tighten centre bolt of LRT-12-200 to remove oil
seal.
6.Remove and discard oil seal from LRT-12-200.
7.Remove thrust button from crankshaft.Refit
1.Clean oil seal recess in oil pump and running
surface on crankshaft, ensure bolt holes are
clean and dry.
2.Fit oil seal guide from seal kit, over end of
crankshaft.
3.Position new seal on crankshaft up against oil
pump housing. Drift seal into place using tool
LRT-12-202.
CAUTION: Oil seal must be fitted dry.
4.Remove LRT-12-202 and oil seal guide from
crankshaft.
5.Clean crankshaft gear and wipe end of
crankshaft.
6.Fit drive gear to crankshaft.
7.Fit camshaft timing belt.

+ ENGINE - K SERIES KV6,
OVERHAUL, Camshaft timing belt.

ENGINE - K SERIES KV6
12-3-82 OVERHAUL
4.Fit new Patchlok bolts securing oil seal to
cylinder block and using sequence shown,
tighten to 8 Nm (6 lbf.ft).
5.Remove oil seal protector LRT-12-061.
6.Clean bolt holes in crankshaft using an old
drive plate bolt with two saw cuts at an angle of
45° to the bolt shank.
7.Clean drive plate and mating face of
crankshaft.
8.Position drive plate to crankshaft and fit but do
not tighten new Patchlok bolts.
9.Position LRT-12-161 and LRT-12-199 to
crankshaft pulley to restrain crankshaft.
10.Using sequence shown, tighten to bolts to:
lStage 1 - 25 Nm (18 lbf.ft)
lStage 2 - 100 Nm (74 lbf.ft)
11.Remove special tool from crankshaft pulley,
loosen bolt and remove LRT-12-161 from LRT-
12-199.
12.Fit automatic gearbox.

+ AUTOMATIC GEARBOX - JATCO,
REPAIRS, Gearbox - KV6 - with engine and
gearbox removed.
Crankshaft
$% 12.21.33.01
Remove
1.Remove cylinder head gaskets.

+ ENGINE - K SERIES KV6,
OVERHAUL, Cylinder head gasket - LH.

+ ENGINE - K SERIES KV6,
OVERHAUL, Cylinder head gasket - RH.
2.Remove oil pump gasket.

+ ENGINE - K SERIES KV6,
OVERHAUL, Oil pump - Overhaul.
3.Remove crankshaft rear oil seal.

+ ENGINE - K SERIES KV6,
OVERHAUL, Crankshaft rear oil seal.
4.Remove engine sump.

+ ENGINE - K SERIES KV6,
OVERHAUL, Sump - engine oil.
Disassembly
1.Remove bolt securing oil pick up strainer,
remove strainer and discard 'O' ring.

ENGINE - K SERIES KV6
12-3-86 OVERHAUL
10.Apply a continuous bead of sealant, Part No.
STC 50550, to paths on lower crankcase as
shown then spread to an even film using a
roller.
CAUTION: To avoid contamination,
assembly must be completed immediately
after application of sealant.
11.Fit 2 M8 slave guide studs into cylinder block at
positions shown.
12.Position lower crankcase to cylinder block.13.Fit and lightly tighten 6 M8 bolts, remove guide
studs, fit and lightly tighten 2 remaining M8
bolts.
14.Using sequence shown, tighten bolts to 25 Nm
(18 lbf.ft).
15.Fit and tighten remaining M8 bolt to 25 Nm (18
lbf.ft).
16.Fit 2 rear M6 bolts and tighten to 9 Nm (7 lbf.ft).
17.Clean oil pick-up strainer and mating face.
18.Lubricate new 'O' ring with clean engine oil and
fit to pick-up strainer.
CAUTION: Ensure 'O' ring, Part No. LYX
000210L is used.
19.Apply sealant, Part No. STC 50552 to threads
of oil pick-up strainer retaining bolt.
20.Position oil pick-up strainer, fit and tighten bolt
to 25 Nm (18 lbf.ft).
21.Clean oil pump, oil seal recess in oil pump body
and mating face on cylinder block, ensure bolt
holes are clean and dry.
22.Clean oil seal running surface on crankshaft.